Deutsch dropdown-ico

Bedienungsanleitung Mustang Survival MD3082

28 Seiten 1.06 mb
Download

Zur Seite of 28

Summary
  • Mustang Survival MD3082 - page 1

    Owner’ s Manual MD3081 Inflatable PFD Manual Inflation Model USCG Approved T ype III MD3082 Inflatable PFD Manual Inflation Model with Harness USCG Approved T ype V MD3083 Inflatable PFD Manual with Automatic Backup Inflation Model USCG Approved T ype II MD3084 Inflatable PFD Manual with Automatic Backup Inflation Model with Harness USCG Approved ...

  • Mustang Survival MD3082 - page 2

    ...

  • Mustang Survival MD3082 - page 3

    CONTENTS P age 1 Approval Conditions and Carriage Regulations 2 What is an Inflatable PFD? 2 Instructions for Use 2 Component Inspection Instructions 3 Readiness Checklist 4 Sizing and Fit 4 Donning Instructions 5 Inflating Your Inflatable PFD 6 Special Considerations for Automatic Devices (MD3083 and MD3084) 7 Deflating the Inflatable PFD 8 Usage ...

  • Mustang Survival MD3082 - page 4

    DO NOT REMO VE PRIOR TO SALE. APPROV AL CONDITIONS AND CARRIAGE REGULA TIONS T his Inflatable PFD is approved by the U .S . Coast Guard (USCG) for use as a Type III (Model MD3081), T ype V (Model MD3082) Personal Flotation Device (PFD), Type II (Model MD3083), and T ype V (Model MD3084) P ersonal Flotation Device (PFD). Models MD3082 and MD3084 hav ...

  • Mustang Survival MD3082 - page 5

    WHA T IS AN INFLA T ABLE PFD? While traditional PFDs are inherently buoyant, inflatable PFDs , rely entirely on inflation for buoyancy . Uninflated, the Inflatable PFD is a comfortable slim collar that can be inflated at any time with a 33-gram CO 2 gas cylinder . T he Inflatable PFD is designed to offer maximum mobility with minimum bulk. The Infl ...

  • Mustang Survival MD3082 - page 6

    MD3083 and MD3084 Service Indicator Automatic Inflator FIGURE 2 3) Ensure the oral-inflation dust cap is in the stowed position (F ig. 7). 4) Ensure the service indicator is green and the pull-tab lanyard is hanging on the outside; secure the Velcro™ strips on both sides of the Inflatable PFD . 5) F or the MD3083 and MD3084 only - Ensure the bobb ...

  • Mustang Survival MD3082 - page 7

    Y our Inflatable PFD is ready for use if all applicable boxes are check ed. NO TE: Contact your Mustang Dealer if you have any concerns about the readiness of your Inflatable PFD . Sizing and Fit T his PFD provides a minimum of 33.7 lbs of buoyancy when inflated and is designed for wearers over 16 years of age , with a chest range of 30-52 inches ( ...

  • Mustang Survival MD3082 - page 8

    Inflating Y our Inflatable PFD It is recommended that the following procedures be followed to inflate your Inflatable PFD: 1) Manual Inflation Activate the inflation system by jerking firmly downw ard on the pull- tab (F ig. 4). T he Inflatable PFD should fully inflate within 5 seconds . MD3081 and MD3082 MD3083 and MD3084 Manual Inflator Automatic ...

  • Mustang Survival MD3082 - page 9

    PFD , first locate the oral inflation tube by opening the wearer ’ s left front panel of the Inflatable PFD . Remove the dust cap from the end of the oral tube and blow into the tube until the Inflatable PFD is fully inflated. WARNING: A void double inflation (CO 2 cylinder inflation after full oral inflation) as it could damage the PFD . FIGURE ...

  • Mustang Survival MD3082 - page 10

    If this PFD should inflate prematurely , a re-arm kit (MA7202) is required to re-arm the device . IMPORT ANT : The Inflatable PFD should be re-armed according to the instructions (Re-arming Y our PFD (MD3083 and MD3084) p . 10). Deflating the Inflatable PFD 1) T o deflate the Inflatable PFD , reverse the oral-inflation tube dust cap and insert it i ...

  • Mustang Survival MD3082 - page 11

    Usage Below F reezing When the temperature is below freezing, a fully discharged cylinder may not adequately inflate your Inflatable PFD . Under these conditions use the oral inflator to adequately top-up the PFD . WARNING: CO 2 inflation could over -pressurize and damage your Inflatable PFD if already orally inflated. Re-arming Y our PFD (MD3081 a ...

  • Mustang Survival MD3082 - page 12

    MD3081 and MD3082 Manual Inflator Service Indicator Step 5 Cylinder Step 2 O-Ring Step 3 T ab Step 4 Sensor Ring Step 3 Bayonet Lever FIGURE 8 4) Raise , and hold, the lever into the inflator housing. Install a new cylinder/bayonet assembly by engaging bayonet tabs in housing, pushing in then turning clockwise 1/8 turn to a full stop (F ig. 9). WAR ...

  • Mustang Survival MD3082 - page 13

    Ta b Piercing Pin Cylinder Lever Service Indicator MD3081 and MD3082 Manual Inflator 1/8 T urn Cylinder 1/8 T urn Ta b Piercing Pin Lever Service Indicator MD3081 and MD3082 Manual Inflator FIGURE 9 5) Examine the service indicator (F ig. 9) and ensure it is GREEN . If the service indicator is red, the mechanism has been fired or is incorrectly fit ...

  • Mustang Survival MD3082 - page 14

    removed prior to re-arming . 5) Check the housing to be sure it is clear and dry . If necessary , rinse the inflator with fresh water to remove dirt and salt. Let dry before going to step 6. CO 2 Cylinder Step 2 Cylinder / Bayonet Assembly Step 2 Sensor Ring Step 9 Bayonet Ta b Step 9 O-ring Step 9 HOUSING** Step 4 Service Indicator Step 11 Pull-T ...

  • Mustang Survival MD3082 - page 15

    unknown, check the date printed on the bobbin and replace if older than three (3) years (see Re-arming Y our PFD (MD3083 and MD3084), p . 10). 7) IMPORT ANT! Bobbin (yellow) must be installed into the HOUSING (**see figure 10), white side up , aligning the slots on the bobbin with the ridges inside the threaded housing. The bobbin will slide in eas ...

  • Mustang Survival MD3082 - page 16

    12) Refold the Inflatable PFD in accordance with the Repacking section (p . 13). Y OUR INFLA TABLE PFD (MD3083 and MD3084) IS NOW READ Y FOR MANU AL USE WITH A UT OMA TIC BACKUP Service Indicator Groove Pull-cord Ta b Piercing Pin Cylinder MD3083 and MD3084 Automatic Inflator 1/8 T urn FIGURE 12 Repacking Gently squeeze the Inflatable PFD until all ...

  • Mustang Survival MD3082 - page 17

    D C A E W1 R W1 R B B C A D F F D C A E B B C A D F F F D C A B B C A D E F Pull-tab FIGURE 13 FIGURE 14 FIGURE 16 FIGURE 15 Sailing Harness Models with a sailing harness (MD3082 and MD3084) are designed to prevent the user from falling overboard when used with a tether with an under -load quick-release hook and have been designed and tested in acc ...

  • Mustang Survival MD3082 - page 18

    quick-release under -load hardwar e . This harness has not been designed for fall arrest, lifting or climbing and should not be relied upon in any of these instances . US Coast Guard approval does not apply to this harness and the potential for injury has not been assessed. Chest Buckle Chest Belt Webbing Quick Release Lanyard D-Ring Tether Webbing ...

  • Mustang Survival MD3082 - page 19

    Repacking section (p .13). 3) Annually - P erform the following at the beginning of each boating season, after cell inflation, or whenever the integrity of the inflatable cell is in doubt: i) Check all components for dirt or corrosion. Clean or replace. ii) V isually examine your Inflatable PFD for damage or excessive abrasion, wear , tear or conta ...

  • Mustang Survival MD3082 - page 20

    Always store your Inflatable PFD in a w arm, dry place out of direct sunlight. Cleaning and Storing of Y our Inflatable PFD (MD3083 and MD3084) T o clean your Inflatable PFD , remove the CO 2 cylinder/bayonet assembly , cap and bobbin. K eep the bobbin dry . Hand wash or sponge down the Inflatable PFD in warm, soapy water . Rinse the PFD and inflat ...

  • Mustang Survival MD3082 - page 21

    MAINTENANCE INSTRUCTIONS for leak tests p . 14). It should inflate quick and easily . · Learn how it works by:   •ActivatingtheCO 2 inflation system   • Re-arming the CO 2 inflation system   • Using the oral inflator tube T o check the manual inflation system (with CO 2 cylinder/bayonet asse ...

  • Mustang Survival MD3082 - page 22

    is well above the water’ s surface. Note the effect of where you hold your legs on how you float. 5) Get out of the water and remove the Inflatable PFD . Remove the used CO 2 cylinder/bayonet assembly and the used bobbin from the Inflatable PFD inflator . Deflate the Inflatable PFD by depressing the oral inflator valve (see Deflating the Inflatab ...

  • Mustang Survival MD3082 - page 23

    1) No spare parts or re-arming kits are needed to test an Inflatable PFD . 2) Remove the CO 2 cylinder/bayonet assembly to prevent inadvertent inflation, which could potentially damage the Inflatable PFD . Inspect the cylinder to confirm it is unused (F ig. 11). Unscrew and remove the cap and the bobbin (MD3083 and MD3084 only). Otherwise the bobbi ...

  • Mustang Survival MD3082 - page 24

    hypothermia - a substantial loss of body heat, which leads to exhaustion and unconsciousness . Most drowning victims first suffer from hypothermia. The following chart shows the effects of hypothermia: how hypothermia affects most adults . How hypothermia affects most adults W ater Exhaustion or Expected T emperature ˚C (˚F) Unconsciousness T ime ...

  • Mustang Survival MD3082 - page 25

    Y our will-to-live does mak e a difference! 5) If there is more than one person in the water , huddling is recommended while waiting to be rescued. T his action tends to reduce the rate of heat loss and thus increase the survival time . FIGURE 18 HELP P osition EA CH OF THESE DEVICES IS INTENDED T O HELP Y OU SA VE Y OUR OWN LIFE F or your Inflatab ...

  • Mustang Survival MD3082 - page 26

    F or the MD3081 and MD3082 - MA7203 Re-arm Kit – Contains 33-gram replacement CO 2 cylinder/bayonet assembly for the manual inflator . F or the MD3083 and MD3084 - MA7202 Re-arm Kit – Contains 33-gram replacement CO 2 cylinder/bayonet assembly and bobbin for the auto inflator . ADDITIONAL INFORMA TION If you need more information about PFDs and ...

  • Mustang Survival MD3082 - page 27

    ...

  • Mustang Survival MD3082 - page 28

    Mustang Survival and seahorse design is a registered trademark of Mustang Surviv al Corp. Our commitment to quality has earned our Burnaby facilities ISO 9001 registration, the highest of all international standards . This is our guarantee you’re receiving the ultimate in design and manufacturing. HT1090 (Rev 09Aug2011) WE SA VE LIVES FOR A LIVIN ...

Produzent Mustang Survival Kategorie Life Jacket

Dokumente, die wir vom Produzenten des Geräts Mustang Survival MD3082 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Mustang Survival
- Bedienungsanleitungen MD3082
- Produktkarten Mustang Survival
- Informationsbroschüren
- oder Energieetiketten Mustang Survival MD3082
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Mustang Survival MD3082.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Mustang Survival MD3082, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Mustang Survival MD3082. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Mustang Survival MD3082 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Mustang Survival MD3082, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Mustang Survival MD3082 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Mustang Survival MD3082 verständlich ist.

Eine gänzliche Bedienungsanleitung von Mustang Survival sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Mustang Survival MD3082 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Mustang Survival MD3082 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Mustang Survival MD3082, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Mustang Survival MD3082 - die uns die ersten Schritte während der Nutzung von Mustang Survival MD3082 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Mustang Survival MD3082 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Mustang Survival MD3082 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Mustang Survival MD3082?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Mustang Survival MD3082 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Mustang Survival MD3082 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)