Deutsch dropdown-ico

Bedienungsanleitung Jet Tools JJ-6CSDX

40 Seiten 4.1 mb
Download

Zur Seite of 40

Summary
  • Jet Tools JJ-6CSDX - page 1

    Operating Instructions and Parts Manual Woodworking Jointer Models: JJ-6CSX, JJ-6CSDX WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708457DX Ph.: 800-274-6848 Revision A 04/05 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Bookmarked ...

  • Jet Tools JJ-6CSDX - page 2

    2 This manual has bee n prepared for the owner and operators of JJ-6CSX and JJ-6CSDX Woodworkin g Jointers. Its purpose, aside from machine ope ration, is to promote safety through the use of accepted correct operating and main tenance procedures. Com plete ly read the safety and maintenance instructions before operating or servicing the machine. T ...

  • Jet Tools JJ-6CSDX - page 3

    3 Table of Contents Warranty ....................................................................................................................... ................................. 2 Table of Contents .............................................................................................................. ............................ 3 Warni ...

  • Jet Tools JJ-6CSDX - page 4

    4 Warnings 1. Read and understand the entire o wner's manual before attemptin g assembly or operation. 2. Read and understand the warnings posted on the m a chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. This Woodworking Joi ...

  • Jet Tools JJ-6CSDX - page 5

    5 20. Keep visitors a safe distance from the work are a. Keep children aw ay. 21. Make your workshop child proof with padlocks , master switches or by removing starter keys. 22. Give your work undivided attention. Looking a roun d, carrying on a conversation and “horse -play” are careless acts that can result in serious inj ury. 23. Maintain a ...

  • Jet Tools JJ-6CSDX - page 6

    6 39. Move the hands in an alternate motion from ba ck to front as the work continue s through the cut. Never pass the hands directly over the cutter knif e. As one hand approaches the knives remove it from the stock in an a rc motion and place it back on the stock in a position be yond the cutter knife (Fig. 2). 40. At all times hold the stock fir ...

  • Jet Tools JJ-6CSDX - page 7

    7 Introduction This manual is provided by WMH Tool Grou p covering the safe operation and maintena nce procedures for Models JJ-6CSX and JJ-6 CSDX Jointers. This manual contains in structions on installation, safety precautions, general o perating procedures, mainten ance instructions a nd parts breakd own. This machine has been designed and const ...

  • Jet Tools JJ-6CSDX - page 8

    8 Unpacking Open shipping container and che ck for shipping damage. Report any damage imm ediately to your distributor and shipping agent. Do not discard any shipping material until the Jointer is assembled and running properly. Shipping Contents Note: This unit is shipped in two ca rtons. Stand Carton 1 Stand with Motor 1 Stand Cover with Mounting ...

  • Jet Tools JJ-6CSDX - page 9

    9 Assembly Unpacking and Cleanup 1. Carefully finish removing all conte nts from both shipping cartons. Compare contents of the shipping cartons with the list of contents above. Place parts on a protected surfa ce. 2. Report any shipping damage to your local distributor. 3. Clean all rust protect ed surfaces (bed, fence, etc.) with kerosene or di e ...

  • Jet Tools JJ-6CSDX - page 10

    10 Installing Fence to Bed Referring to Figure 3: 1. Take the lock handl e (E), flat washer (F), an d lock nut (G) from the carton . 2. Place the fence assembly (A) onto the table (B). Be sure the key stock (D) on the bed line s up with the channel (C) in the fence casting. 3. Place the flat washer (F) on hole (H)*; insert the lock hand le (E) thro ...

  • Jet Tools JJ-6CSDX - page 11

    11 Installing Belt Guard Referring to Figure 6: 1. Place the belt guard (A) over the openin g in the stand. 2. Line u p the holes in the stand with the holes in the guard. 3. Attach the guard to the stand using four 1/4-20 x 1/2’ pan he ad machine screws (B) and four 1/4” flat washers (C). Installing Cutterhead Guard 1. Remove the screw from th ...

  • Jet Tools JJ-6CSDX - page 12

    Electrical Grounding Instructions This jointer must be grounded while in use to protect the operator from electric sho ck. In the event of a malfunction or br eakdown, grounding provides a path of least resistance fo r electric current to re duce the risk of ele ctric shock. This tool is equipped with an electric cord having an equipmen t-grounding ...

  • Jet Tools JJ-6CSDX - page 13

    13 Extension Cords Make sure your extension co rd is in good condition. When using a n extension cord, be sure to use one heavy enough to carry the current your machine will draw. An undersized cord will cau se a drop in the line voltage resulting in power lo ss and overheating. Table 1 show s the correct size to use depending on the cord length an ...

  • Jet Tools JJ-6CSDX - page 14

    14 Fence Stop Adjustments Periodic ally check the 90 ° and 45° b ackward (135°) tilt accuracy of the fence with an angle measuring device, su ch as an adjustable square or machinist’s pr otractor. 90º Fence Adjustment Referring to Figure 13: The 90º stop is controlled by the stop bolt (E) and the stop block (C). 1. Set the infeed table to ap ...

  • Jet Tools JJ-6CSDX - page 15

    15 Infeed Table Depth Stop Referring to Figure 17: The infeed table depth stop (A) limits the depth of a cut (set by adjusting t he infeed table handwheel) to a maximum depth of 1/8”. For normal operations, the depth of cut should never exceed 1/8", except for rabbetting operations. If a rabbeting operation is desired: 1. Lower the infeed ta ...

  • Jet Tools JJ-6CSDX - page 16

    16 Setting Cutterhead Knives (JJ-6CSX) Cutterhead knives are dangerously sharp! Us e extreme caution w hen inspecting, removing, sharpening or replacing knives into the cutterhe ad. Failure to comply may cause serious injury! 1. Carefully number each blade with a magic marker to make them ea sier to differentiate. 2. Rotate the cutterhead by turnin ...

  • Jet Tools JJ-6CSDX - page 17

    17 Replacing Knives (JJ-6CSX) Planer knives are dang erously sharp. Use extreme caution when inspecting, removing, sharpening, or replacing knives into the cutterhead. Failure to comply may cause serious injury. 1. Disconnect machine from t he power source. 2. Remove blade guard b y turning the knob (A, Fig. 23) clockwise while lifting up on blade ...

  • Jet Tools JJ-6CSDX - page 18

    18 Outfeed Table Adjustment When you receive the jointer, the knives have been pre-set at the factory. However, the height and parallelism of the knives with the outfeed table should be checked, and any needed adjustments made, before putting the jointer into operation. Adjust the height of the outfeed table as follows: 1. Disconnect jointer from p ...

  • Jet Tools JJ-6CSDX - page 19

    19 Setting Cutterhead Knives (JJ-6CSDX) Note : Before setting knives for model JJ-6CSDX Jointer, the Outfeed Table Adjustment shoul d be done to ensure the proper knife hei ght in relation to the outfeed table. Knives for the JJ-6CSDX cutterhead are adjusted by means of a cam. It is important to note that the entire adjustment is accomplished withi ...

  • Jet Tools JJ-6CSDX - page 20

    20 Replacing Knives (JJ-6CSDX) Planer knives are dang erously sharp. Use extreme caution when inspecting, removing, sharpening, or replacing kniv es. Failure to comply may cause serious injury. To remove and replace a knife (Refer to Figure 29): 1. Remove four gib screws (A) with a 4m m hex wrench. 2. Remove the gib (B) and knife (C). If the knife ...

  • Jet Tools JJ-6CSDX - page 21

    21 Determining Correct Table Height When you receive the jointer, the knives have been pre-set at the factory. However, the height and parallelism of the knives with the outfeed table should be checked, and any needed adjustments made, before putting the jointer into operation. The outfeed table and cutterh ead kniv es are correctly adjusted when a ...

  • Jet Tools JJ-6CSDX - page 22

    22 Operating Controls 1. Hand Wheel for Outfeed Table 2. Outfeed Table 3. Fence 4. Fence Adjustment Handle 5. Cutter Guard 6. Infeed Table 7. Hand Wheel for Infeed Table 8. On/Off Switch Operation Important : If you are inexperienced at jo inting, use scrap piec es of lumber to c heck setting s and get the feel of operations before attempting re gu ...

  • Jet Tools JJ-6CSDX - page 23

    23 Hand Placement Never pass hands directly over the cutterhead. At the start of the cut, the left hand holds the workpiece firmly against the infeed ta ble and fence while the right hand pushes the workpiece in a smooth, even motion toward the cutterhea d (Figure 34). After the cut is unde r way, the new surface rests firmly on the outfeed table. ...

  • Jet Tools JJ-6CSDX - page 24

    24 Rabbeting A rabbet is a groove cut along the edge of a board. See Figure 37. The widt h and thickness of the wood to be rabbeted depends upo n the width and length of the rabbet. However, never ra bbet a piece of wood less than 12” long. Note: The knives must be extended beyond the cutterhead by 1/32”. See the Replacing Knives in Cutterhead ...

  • Jet Tools JJ-6CSDX - page 25

    25 Beveling To cut a bevel, lock the fence at the required angle and run the work piece across the knives while keeping it firmly against the fence and tables. Several passes may be nece ssary to achieve the desired result. Although the fence may be tilted in or out for a bevel cut, it is recommended for safety reasons th at the fence be tilted in ...

  • Jet Tools JJ-6CSDX - page 26

    26 Cutterhead Removal The entire cutterhead assembly may be removed for cleaning or for bearing and blade replacement. Some woodworkers keep a sp are cutterhead with replacement blades should the original cutterhea d have to be repaired. Blades in the cutterhead ar e sharp! Use extreme caution when handling the removal of the cutterhead. Failure to ...

  • Jet Tools JJ-6CSDX - page 27

    27 13. To re-install the cutterhead, reverse the above steps. Note: Make sure that the f ence base casting is level with the Outfeed table when securing. Lubrication  Use a good grade of light grease on t he steel adjusting screws located in the raising and lowering mechanisms of the work table s.  Occasionally, apply a few drops of light mac ...

  • Jet Tools JJ-6CSDX - page 28

    28 Troubleshooting Mechanical and Electrical Problems Trouble Probable Cause Remedy No incoming power. Verify unit is connected to power, on- button is pushed in completely, and stop-button is disengaged. See page 24. Building circuit breaker trips or fuse blows. Verify that jointer is on a circuit of correct size. If circuit s ize is correct, ther ...

  • Jet Tools JJ-6CSDX - page 29

    29 Trouble Probable Cause Remedy Machine will not start/restart or repeatedly trips circuit breaker or blows fuses. On/off switch failure. If the on/off switch is suspect, you have two options: Have a qualified electrician test the switch for function, or purchase a new on/off switch and establish if that was the problem on change out. Optional Acc ...

  • Jet Tools JJ-6CSDX - page 30

    30 Fence – Parts All Models Index No. Part No. Description Size Qty. ................. JEJ-FW .................... Fence Asse mbly Complete (JJ-6CSX) ................ ................................... .1 ................. JJ6CSDX-FAC ......... Fence Ass embly Complete (J J-6CSDX).............. .................................... 1 1 .......... ...

  • Jet Tools JJ-6CSDX - page 31

    31 Fence – Assembly All Models ...

  • Jet Tools JJ-6CSDX - page 32

    32 Stand – Parts All Models Index No. Part No. Description Size Qty. 1 ............... JI-Y01W ................... Stand Body........................................................... ................ .................... 1 2 ............... JI-Y01AW ................. Acc ess Cover ....................................................... ........ ...

  • Jet Tools JJ-6CSDX - page 33

    33 Stand – Parts and Assembly All Models 45 ............. TS-0561031 ............. He x Nut ................................................................ 3/8”-16........... .............. 1 46 ............. JC-M05 .................... Door Latch............................................................ ................ .................... ...

  • Jet Tools JJ-6CSDX - page 34

    34 Bed – Parts All Models Index No. Part No. Description Size Qty. 1 ............... JI-T01W ................... Base ..................................................................... ............ ........................ 1 2 ............... JI-T02W ................... Front Table (JJ-6CSX) ......................................... .......... ...

  • Jet Tools JJ-6CSDX - page 35

    35 54 ............. 5F-H051 ................... Rivet ..................................................................... .................................... 6 55 ............. TS-0207021 ............. Socket Head Cap Screw (JJ-6CSDX) ................. 1/4”-20x1/2” ................ 1 ...

  • Jet Tools JJ-6CSDX - page 36

    36 Cutterhead – Parts and Assembly JJ-6CSX Index No. Part No. Description Size Qty. ................. JEE-C01A ................ Cutterhead Assemb ly (Index #s 1-14) ................. .................................. .. 1 1 ............... JC-C06 ..................... Hex Sc rew ............................................................ ...... ...

  • Jet Tools JJ-6CSDX - page 37

    37 Cutterhead – Parts and Assembly JJ-6CSDX Index No. Part No. Description Size Qty. ................. JJ6CSDX-CA ........... Cutterhead Assemb ly (Index #s 1-15) ................. .................................... 1 1 ............... JJ6CSDX-101 .......... Special Butto n Head Socket Screw ..................... ............................... ...

  • Jet Tools JJ-6CSDX - page 38

    38 Wiring Diagram – All Models WHI TE BLACK BLACK WHI TE GREEN GREEN GROUND 300MFD 125 VAC ELECTRICAL SCHEMATIC - 115V RED YELLOW BLACK WHITE BLACK WH ITE GREEN GREEN ELECTRICAL SCHEMATIC - 230V GROUND BLACK WHI TE GREEN BLACK WH ITE GREEN WH I TE BLACK WHI TE RED YELLOW BLACK 300MFD 125 VAC START STOP STOP START ...

  • Jet Tools JJ-6CSDX - page 39

    39 Notes ...

  • Jet Tools JJ-6CSDX - page 40

    40 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m ...

Produzent Jet Tools Kategorie Biscuit Joiner

Dokumente, die wir vom Produzenten des Geräts Jet Tools JJ-6CSDX erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Jet Tools
- Bedienungsanleitungen JJ-6CSDX
- Produktkarten Jet Tools
- Informationsbroschüren
- oder Energieetiketten Jet Tools JJ-6CSDX
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Jet Tools JJ-6CSDX.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Jet Tools JJ-6CSDX, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Jet Tools JJ-6CSDX. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Jet Tools JJ-6CSDX ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Jet Tools JJ-6CSDX, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Jet Tools JJ-6CSDX hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Jet Tools JJ-6CSDX verständlich ist.

Eine gänzliche Bedienungsanleitung von Jet Tools sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Jet Tools JJ-6CSDX bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Jet Tools JJ-6CSDX befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Jet Tools JJ-6CSDX, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Jet Tools JJ-6CSDX - die uns die ersten Schritte während der Nutzung von Jet Tools JJ-6CSDX erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Jet Tools JJ-6CSDX hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Jet Tools JJ-6CSDX im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Jet Tools JJ-6CSDX?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Jet Tools JJ-6CSDX nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Jet Tools JJ-6CSDX hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)