Deutsch dropdown-ico

Bedienungsanleitung Chamberlain 1022

30 Seiten 4.04 mb
Download

Zur Seite of 30

Summary
  • Chamberlain 1022 - page 1

    Models 1022/1024/1042 GARAGE DOOR OPENERS Includes INTELLICODE ® Remote Control Safe-T -Beam ® System must be installed to close door . For use only with sectional doors. Y our Residential Opener comes with a Rail Assembly which is standard for up to a 7 foot high door . Homelink ® and Car2U ® compatible For Answers and Assistance: 1.800.354.36 ...

  • Chamberlain 1022 - page 2

    PN# 3642036534, 02/26/2010 REV . 1 2 OVER VIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMA TION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on the own ...

  • Chamberlain 1022 - page 3

    PN# 3642036534, 02/26/2010 REV . 1 3 T ABLE OF CONTENTS OPENER FEA TURES INTELLICODE ® Rolling Code Security System. An electronic rolling code system that enhances the security of the door opener by continuously changing the access code each time the remote control is used. The door opener responds to each new code only once. An access code copie ...

  • Chamberlain 1022 - page 4

    PN# 3642036534, 02/26/2010 REV . 1 6 T o avoid damage to your door and/or opener , make sure you disable and/or remove any door locks, ropes, and/or cables (NOT door lif t cables) prior to inst alling your opener . ( Refer to Section 1.) 4 PRE-INST ALLA TION CHECK LIST FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM Things to consider if you are ...

  • Chamberlain 1022 - page 5

    PN# 3642036534, 02/26/2010 REV . 1 5 TYPICAL SECTIONAL DOOR INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM TYPICAL SUPPORT BRACKET (NOT PROVIDED) EXTENSION SPRING OR TORSION SPRING SAFE-T -BEAM ® BRACES ADDED HEADER BRACKET MOUNTING BOARD POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLET 4 1 3 6 2 3 5 SECTIONAL DOOR Pg. 19 Pg. ...

  • Chamberlain 1022 - page 6

    PN# 3642036534, 02/26/2010 REV . 1 6 RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3/16" Drill Bit 1/4", 7/16", 3/8" and 1/2" Sockets S tep ladder Drill Ratchet Carpenter ’s level Pencil T ape measure Wire strippers Phillips screwdriver Adjustable wrench P ARTS IDENTIFICA TION - Not Shown Full Size ...

  • Chamberlain 1022 - page 7

    PN# 3642036534, 02/26/2010 REV . 1 F ASTENERS - Shown Full size ( See Parts List below for full description.) Lag screw - 5/16" x 2" Self-drilling Screw 1/4"-20 x 3/4" Hex Flange Nut 1/4"-20 Cotter pin Clevis pin 5/16" x 3/4" Hex Bolt - 5/16"-18 x 3/4" Hex Flange Nut 5/16"-18 Rail Clamp Bolt - 5/16& ...

  • Chamberlain 1022 - page 8

    PN# 3642036534, 02/26/2010 REV . 1 8 1-PIECE RAIL HARDW ARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3-PIECE RAIL HARDW ARE ASSEMBLED VIEW T ensioner Rail with chain Chain Chain Connector Release Knob Header Bracket Po wer Head Pow er Cord Carriage Assembly Clevis Pin, Long & Cotter Pin N T S me doo s e d b ra n g Con a ...

  • Chamberlain 1022 - page 9

    PN# 3642036534, 02/26/2010 REV . 1 9 PENER ASSEMBL Y FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 NOTE: Three (3) piece rail assemblies are for a 7 foot high door . Clear a workspace area to unp ack and organize box and contents for assembly . 1. There are 4 boxes inside the carton. Each box is numbered 1 - 4. Note that some openers will co ...

  • Chamberlain 1022 - page 10

    10 FIG . 1-2 Split Rail sections . FIG . 1-3 Split Rail assembly . A B Chain Rail Center Rail End Rail Wire Tie(s) Rail Assembly for CHAIN DRIVE OPENER NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1. 3. Remove the two rail sections that are not connected to the chain and place them on floor (Fig. 1-2, A). 4. Carefully remove t ...

  • Chamberlain 1022 - page 11

    POWER HEAD & RAIL ASSEMBL Y Assembly for CHAIN DRIVE OPENER NOTE: Handle carefully! Drive chain can slide out of rail. NOTE: For power head and rail assembly locate Bag 1 from Box 1. NOTE: Copy serial number from power head frame and record it on warranty page. NOTE: Standing at the powerhead, facing the door, the bullet MUST be on the RIGHT si ...

  • Chamberlain 1022 - page 12

    12 PN# 3642036534, 02/26/2010 REV . 1 FIG . 2-2 Finding highest point of travel . NST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 2 HEADER AND DOOR MOUNTING BRACKETS: 1. Finding header bracket mounting location . • Close garage door . – Use a pencil and level. a) Mark center of garage door (one-half overall width) on the wall w ...

  • Chamberlain 1022 - page 13

    MOUNTING THE OPENER: 1. Getting st arted . • Position assembled rail on wall next to header bracket (Fig. 2-4) . – Place material on floor under power head to protect from scratching. (A box, stool, or similar device may be needed to clear a torsion spring.) NOTE: For header bracket pins locate Bag 2 from Box 1. 2. Mounting the assembly . • A ...

  • Chamberlain 1022 - page 14

    14 PN# 3642036534, 02/26/2010 REV . 1 DOOR BRACKET : NOTE: For door bracket and bolts locate Bag 4 from Box 2. 1. Finding door bracket mounting location . • Door bracket is mounted as high on door as possible along vertical centerline and NO LOWER THAN top set of rollers (Fig. 2-7) . 2. Mounting the door bracket . • Proper bracing should be ver ...

  • Chamberlain 1022 - page 15

    PN# 3642036534, 02/26/2010 REV . 1 NOTE: For Wall Console, wire and insulated staples locate Bags 6 and 7 from Box 2. 1. W all Console location.  W all Console location should be in direct sight of door .  It should be at least five feet (5') above floor to prevent small children from operating door .  It must be away from any moving ...

  • Chamberlain 1022 - page 16

    PN# 3642036534, 02/26/2010 REV . 1 16 3.Securely fasten wires.  Securely fasten wires to ceiling and wall using insulated staples provided. – Use insulated staples. – S taples should be snug only .  If rear cover is attached to power head, remove it.  On power head: – Route wall console wires through wire guide on power head. – S p ...

  • Chamberlain 1022 - page 17

    PN# 3642036534, 02/26/2010 REV . 1 17 AFE-T -BEAM ® SYSTEM INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 4 NOTE: The opener will not close the door automatically unless the Safe-T -Beam ® System is installed. NOTE: For Safe-T-Beam®, screws, wire, and insulated staples locate items and Bag 8 from Box 3. 1. Mounting bracket s . ...

  • Chamberlain 1022 - page 18

    PN# 3642036534, 02/26/2010 REV . 1 18 3b. Wiring (pre-wired) .  Route wire from wall to Safe-T -Beam ® sensors (Fig. 4-5b) .  S plice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash and plain-to-plain . - T rim sensor wire to approximately one foot (1 ft) from sensor . - S plit and strip ends of sensor wires and pre-wired ...

  • Chamberlain 1022 - page 19

    PN# 3642036534, 02/26/2010 REV . 1 19 ONNECTING TO POWER FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 5 Plug the opener into a properly grounded electrical outlet (Fig. 5-1).  T o reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third ( grounding ) pin. This plug will only fit a grounded type out ...

  • Chamberlain 1022 - page 20

    PN# 3642036534, 02/26/2010 REV . 1 20 OOR LIMITS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 6 The OPEN (UP) and CLOSE (DOWN) door positions are controlled by making the adjustments on the panel located on the bottom of the power head. The adjustments that can be made are: • Close T ravel Limit, • Open T ravel Limit, Maximum Closing Forc ...

  • Chamberlain 1022 - page 21

    21 Obtain st andard emergency release kit and remove S-hook from the cable end that attaches to the opener carriage. 1. Attach the emergency release cable loop end to the opener carriage as shown (FIG 6-4). Properly connecting the release cable to the carriage fitting will enable the correct carriage release action for the opener . FIG . 6-4 Emerge ...

  • Chamberlain 1022 - page 22

    PN# 3642036534, 02/26/2010 REV . 1 22 FIG . 6-6 2 x 4 under center of door opening. CONT ACT REVERSE TEST The force adjustment s and limit switch settings MUST BE COMPLETED before testing. 1. T esting .  Open garage door using wall button. – Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-6) .  Close ...

  • Chamberlain 1022 - page 23

    PN# 3642036534, 02/26/2010 REV . 1 23 FCC and IC CER TIFIED FIG . 7-1 Learn code button and LED SET SET OPEN FORCE CL OSE C ODE LEARN LIMIT MANU AL Open T ravel Limit Open Set Limit Button Close T ravel Limit Close Set Limit Button Down Forc e Control Adjustment Up Force Control Adjustment Learn Code Button LED Indicator Light To Garage Door This d ...

  • Chamberlain 1022 - page 24

    EMOTE CONTROL BA TTERY REPLACEMENT AND VISOR CLIP INST ALLA TION 8 FIG . 8-1 Open battery cover . 1. Battery replacement . • T o open gently push straight out on battery cover lock tab as shown (Fig. 8-1) . • Flip open battery cover . – Remove old battery . • Make sure new battery is facing proper direction (Match battery polarity with symb ...

  • Chamberlain 1022 - page 25

    PN# 3642036534, 02/26/2010 REV . 1 25 Use wall button supplied with opener . Any other wall control can cause the opener to operate unexpectedly . W ARNING If you have any questions, please do not hesitate to cont act Genie ® customer service at: 1.800.354.3643 IMPORT ANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let childr ...

  • Chamberlain 1022 - page 26

    PN# 3642036534, 02/26/2010 REV . 1 26 CIRCUIT WIRING DIAGRAM FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 2 3 4 5 6 12 34 12 3 12 POWER CORD CORDON DE SECTEUR CABLE ELÉCTRICO TERMINAL BLOCK BORNE BLOQUE DE TERMINALES WHITE BLANC BLANCO BLACK NOIR NEGRO GREEN VERT VERDE SURGE PROTECTOR (MOV) LIMITEUR DE SURTENSION PROTECTOR DE SOBRETENSIONE ...

  • Chamberlain 1022 - page 27

    PN# 3642036534, 02/26/2010 REV . 1 27 TROUBLESHOOTING GUIDE - OPERA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM PROBLEM WHA T T O DO Opener does NOT run from W all Console.  Check power source. – Plug a lamp into outlet used for power head. If lamp works, power source is O K. – If not, check fuse or circuit breaker .  If power ...

  • Chamberlain 1022 - page 28

    PN# 3642036534, 02/26/2010 REV . 1 TROUBLESHOOTING GUIDE - POWER HEAD LED FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM Power head LED Possible Problem Solution Red LED showing Green LED showing OFF OFF Normal operation None required Continuous ON  Programming incomplete  Complete programming 1 BLINK, Pause (Repeat)  T ransmitter has ...

  • Chamberlain 1022 - page 29

    PN# 3642036534, 02/26/2010 REV . 1 29 T ransmitters comply with all United S tates and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country , the importer must determine compliance with any local laws a ...

  • Chamberlain 1022 - page 30

    GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified opener Model 10 22 or opener Model 1024 or opener Model 1042 (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship ...

Produzent Chamberlain Kategorie Garage Door Opener

Dokumente, die wir vom Produzenten des Geräts Chamberlain 1022 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Chamberlain
- Bedienungsanleitungen 1022
- Produktkarten Chamberlain
- Informationsbroschüren
- oder Energieetiketten Chamberlain 1022
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Chamberlain 1022.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Chamberlain 1022, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Chamberlain 1022. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Chamberlain 1022 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Chamberlain 1022, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Chamberlain 1022 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Chamberlain 1022 verständlich ist.

Eine gänzliche Bedienungsanleitung von Chamberlain sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Chamberlain 1022 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Chamberlain 1022 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Chamberlain 1022, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Chamberlain 1022 - die uns die ersten Schritte während der Nutzung von Chamberlain 1022 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Chamberlain 1022 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Chamberlain 1022 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Chamberlain 1022?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Chamberlain 1022 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Chamberlain 1022 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)