Bedienungsanleitung Antec Skeleton

14 Seiten Betrifft nicht
Download

Zur Seite of 14

Summary
  • Antec Skeleton - page 1

    SKELETON User’s Manual ...

  • Antec Skeleton - page 2

    Table of Contents Introduction 1.1 Case Specifications………………...……………......…………… 2 1.2 Diagram……………………………………………....…......……… 2 1.3 How to Carry the Skeleton…………………………….…......…. 3 Hardware Installation Guide 2.1 Removing/Replacing the Component Tray? ...

  • Antec Skeleton - page 3

    1 At Antec, we continually refine and improve our products to ensure the highest quality. As such, it’s possible that your new case may differ slightly from the description in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. ...

  • Antec Skeleton - page 4

    2 1.1 Case Specifications Case Type Open Case Design Color Metallic Silver Dimensions 13”(H) x 14.8”(W) x 16.5”(D) 33.02 (H) x 37.6 cm (W) x 41.9 cm (D) Weight 15.5 lbs / 7 kg Cooling 1 x Super Big Boy 250mm Multi-LED Fan 1 x 92mm Hard Drives Fan Drive Bays 2 x Quick Release 5.25” Bays 2 x Quick Release 3.5” Bays 4 x Externally Mounted 3. ...

  • Antec Skeleton - page 5

    3 1.3 How to Carry the Skeleton The Skeleton case is designed to be held by either set of grips on the top of the side railing. Use these handles when moving or transporting your case. Do not carry the case by the plastic PCI holder, as it was not designed to be a load-bearing device. Hardware Installation Guide This manual is not designed to cover ...

  • Antec Skeleton - page 6

    4 2. To completely remove the Component Tray from the Frame, find the release tab on the lower left side of the Component Tray when the Tray is fully extended. Press it upwards, then pull the Tray out and completely free of the Frame. 3. To replace the Component Tray in the Frame, align the Tray with the back of the case, and slide it forward. Once ...

  • Antec Skeleton - page 7

    5 3. Place the motherboard on the brass standoffs. Screw in the motherboard to the standoffs with the provided Phillips-head screws. Replace the Motherboard Tray onto the Component Tray, and the Component Tray in the Frame as detailed in sections 2.1 and 2.2. Note : You do NOT need to install an I/O panel for Skeleton. Your motherboard should come ...

  • Antec Skeleton - page 8

    6 3. Slide the plate-mounted power supply into the bottom level of the Component Tray until it locks into position. There are two possible locations to mount the power supply, depending on the size of your equipment. Note : Power supplies equipped with an 80mm fan will draw air through the Skeleton and power supply more effectively. We recommend po ...

  • Antec Skeleton - page 9

    7 4. Connect the data and power connectors from the motherboard and power supply to the device. Note : It may be necessary to remove the motherboard tray and/or side screens as detailed in sections 2.2 and 2.3 to effectively route cables to your devices. 2.8 3.5” Device Frame-Mounted Installation Your Antec Skeleton case has the ability to mount ...

  • Antec Skeleton - page 10

    8 Connecting the Front I/O Port s 3.1 USB 2.0 Ports Connect the front I/O panel USB cable to the USB header pin on your mother- board. Check the motherboard manual to ensure that it matches the table below: Motherboard USB Pin Layout Locate the internal USB connector on your motherboard and connect the corresponding cable. 3.2 eSATA Port Connect th ...

  • Antec Skeleton - page 11

    9 3.4 AC’97/HD Audio Ports Connected to your front I/O panel there is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector. The pin assignments for these connectors are as follows: Pin Assignment for Audio Ports (HDA and AC’97) You can connect either the AC’97 or the HDA connector, but not b ...

  • Antec Skeleton - page 12

    10 Cooling System 4.1 The Super Big Boy 250mm Multi-LED Fan The Skeleton’s unique and innovative open case design provides that only one Super Big Boy 250mm Multi-LED fan is required to cool most of your system components. This overhead fan is adjustable, allowing you to choose the best speed suited to your needs. The fan speed switch is located ...

  • Antec Skeleton - page 13

    11 4.3 Removing the 92 mm Hard Drive Fan Ensure that the fan power cable is disconnected before removing the fan. 1. While facing the front of the case, depress the two tabs on the top of the 92mm fan and detach it from the front of the hard drive housing. 2. Remove the four screws on the front of the fan casing. 3. Pull the fan out of the fan hous ...

  • Antec Skeleton - page 14

    Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec ...

Produzent Antec Kategorie Computer case

Dokumente, die wir vom Produzenten des Geräts Antec Skeleton erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Antec
- Bedienungsanleitungen Skeleton
- Produktkarten Antec
- Informationsbroschüren
- oder Energieetiketten Antec Skeleton
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Antec Skeleton.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Antec Skeleton, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Antec Skeleton. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Antec Skeleton ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Antec Skeleton, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Antec Skeleton hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Antec Skeleton verständlich ist.

Eine gänzliche Bedienungsanleitung von Antec sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Antec Skeleton bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Antec Skeleton befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Antec Skeleton, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Antec Skeleton - die uns die ersten Schritte während der Nutzung von Antec Skeleton erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Antec Skeleton hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Antec Skeleton im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Antec Skeleton?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Antec Skeleton nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Antec Skeleton hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)