Bedienungsanleitung Accel 3302

43 Seiten 2.39 mb
Download

Zur Seite of 43

Summary
  • Accel 3302 - page 1

    T empest ® Hot Air Dr ying System Installation Instructions Ry obi 3302 Itek 3985 A.B. Dic k 9985 X88-43 01/2001 Rev-B 2740 ...

  • Accel 3302 - page 2

    GENERAL INFORMA TION Accel Graphic Systems provides parts and service through its authorized distributors and dealers. Therefore, all requests for parts and service should be directed to your local dealer. The philosophy of Accel Graphic Systems is to continually improve all of its products. Written notices of changes and improvements are sent to A ...

  • Accel 3302 - page 3

    GENERAL INFORMA TION 3 ELECTRICAL REQUIREMENTS IMPORT ANT INFORMA TION SAFETY INFORMA TION TERMINOLOGY 220 VAC 50/60 HZ 20 AMP DEDICATED LINE NEMA L620R RECEPTACLE The use of heat to accelerate drying may require more frequent lubrication and/or use of a high temperature lubricant in the delivery of the press. Please consult your press manufacturer ...

  • Accel 3302 - page 4

    GENERAL INFORMA TION 4 HO T AIR VS INFRARED WHA T MAKES TEMPEST ® WORK Although the technology behind the Tempest ® dryer was significant enough to be awarded the GATF Intertech Award, it is by no means new. In fact, thermistors have been in use for many years. They were originally used in motors and other devices as a heat controller and later u ...

  • Accel 3302 - page 5

    GENERAL INFORMA TION 5 HO W DR YING IS A CCOMPLISHED WITH TEMPEST ® KEY F A CT ORS T O REMEMBER ABOUT DR YERS FOR SMALL OFFSET PRESSES. IR dryers use very high temperatures and a fixed amount of electricity. One of the drawbacks of using a very hot heat source is that heat wants to travel from a very high temperature to a very low temperature. In ...

  • Accel 3302 - page 6

    6 ...

  • Accel 3302 - page 7

    7 1 2 3 INST ALLA TION Cut the sprayer hose about halfway between the hopper and the spra y bar . A new hose will be attached to the spra y mechanism. Remove the spray bar by removing the two bolts holding the bracket (subject arrow). Also remove the clip holding the spray hose (subject arrow , picture on following page). DISCONNECT THE PO WER T O ...

  • Accel 3302 - page 8

    8 ...

  • Accel 3302 - page 9

    9 INST ALLA TION Install the mounting bracket and new chain guide using M5 X 16MM cap head bolts and lock w ashers (subject arrow) as shown at the OPS & NOPS. Lea v e the bolts loose so the position of the dr yer can be mov ed up and down. The bolts thread into the same holes that held the original chain guides. 4 Remove the chain guide (subjec ...

  • Accel 3302 - page 10

    10 ...

  • Accel 3302 - page 11

    11 INST ALLA TION 6 Secure the dryer to the brac k ets (f our places) using the shor t button head bolts, w asher , and flanged nut (subject arrows). Leav e the bolt loose so the dryer can be moved front to back. 7 Note: If the press is equipped with an Airtech sprayer , you m ust remove the spray bar from the dryer before installing it in the pres ...

  • Accel 3302 - page 12

    12 ...

  • Accel 3302 - page 13

    13 INST ALLA TION 9 8 P osition the dr y er so it clears the gr ipper opening mechanism on all three delivery gripper bars. The ar m must clear both the top and bottom of the dr yer . The photo shows the ar m clear ing the top of the dr yer (subject arro w). After positioning the dr y er , tighten the bolts holding the mounting brackets to the pres ...

  • Accel 3302 - page 14

    14 ...

  • Accel 3302 - page 15

    15 INST ALLA TION 10 Connect the two hoses together using the "Y" connector (left hand subject arrow). Connect the T empest ® Spra y line to the press spra y hopper line using the reducer (right hand subject arrow). Attach the exhaust fan/manifold assembly to the center of the deliv er y guard as shown. Make sure that the arro w on the f ...

  • Accel 3302 - page 16

    16 ...

  • Accel 3302 - page 17

    17 INST ALLA TION 13 14 15 Attach the micros witch cable assemb ly to the micros witch's in- stalled in step 12. See diag ram f or proper connection. Find a suitable location for the main Tempest electrical box on the NOPS of the press. Route the exhaust fan cable (this cable has female pins in the connector on the end) into the delivery and c ...

  • Accel 3302 - page 18

    18 ...

  • Accel 3302 - page 19

    19 16 17 18 INST ALLA TION Remov e one of the two screws that attach the guard prop to the deliv ery guard on the NOPS. Install the supplied longer M4 screw in its place and using the original nut secure the provided cab le clamp (subject arrow) to the underside of the guard. Make sure y ou hav e the exhaust f an cab le going through the clamp bef ...

  • Accel 3302 - page 20

    20 ...

  • Accel 3302 - page 21

    21 19 20 INST ALLA TION Use the provided zip ties to secure all loose cab les. See the back of the manual f or a complete electr ical system diagram. Replace all cov ers and guards. Attach the supplied multiple po wer cord caution label to the press side NOPS cov er . ...

  • Accel 3302 - page 22

    OPERA TION & MAINTENANCE 22 HO W DR YING IS A CCELERA TED WITH TEMPEST ® HO W TEMPEST ® W ORKS Tempest ® creates a two-step drying process when used with oil-base inks. These steps are: 1. Skinning the surface of the ink with the initial blast of hot air to prevent set off. 2. Accelerating the final drying process approximately 20 o F over t ...

  • Accel 3302 - page 23

    OPERA TION & MAINTENANCE 23 NORMAL OPERATION Pressing the HEAT switch will illuminate both the green and yellow LEDs on the remote control unit. The green LED indicates that the fans (both dryer and exhaust fans if so equipped) are running while the yellow LED indicates that the dryer is armed and the heat will come on automatically when the pr ...

  • Accel 3302 - page 24

    OPERA TION & MAINTENANCE 24 MAINTENANCE KEYS T O REMEMBER F A CT ORS THA T EFFECT DR YING 1. Speed of the press. 2. Amount of ink coverage and color. 3. Type of stock being printed. 4. Initial temperature of paper. In time and with practice you will learn which settings are best for your particular shop. 1. The Tempest ® takes about 12 sheets ...

  • Accel 3302 - page 25

    25 OPERA TION & MAINTENANCE 1. Accel equipment should only be installed by an authorized dealer or distributor. 2. Only use ink or varnish that are explosion safe when used with the Tempest ® . (Refer to the MSDS of ink in use) 3. Make sure to visually check the delivery that the cables in use are not causing a dangerous situation while in ope ...

  • Accel 3302 - page 26

    26 ...

  • Accel 3302 - page 27

    27 ...

  • Accel 3302 - page 28

    28 ...

  • Accel 3302 - page 29

    29 ...

  • Accel 3302 - page 30

    30 ...

  • Accel 3302 - page 31

    31 ...

  • Accel 3302 - page 32

    32 ...

  • Accel 3302 - page 33

    33 ...

  • Accel 3302 - page 34

    34 ...

  • Accel 3302 - page 35

    35 ...

  • Accel 3302 - page 36

    36 ...

  • Accel 3302 - page 37

    37 ...

  • Accel 3302 - page 38

    38 ...

  • Accel 3302 - page 39

    39 ...

  • Accel 3302 - page 40

    40 ...

  • Accel 3302 - page 41

    41 ...

  • Accel 3302 - page 42

    ...

  • Accel 3302 - page 43

    11103 Indian Trail, Dallas, TX 75229 Phone 972-484-6808, Fax 800-365-6510 E-mail info@accel-us.com, Web Site www.accel-us.com ...

Produzent Accel Kategorie Hair Dryer

Dokumente, die wir vom Produzenten des Geräts Accel 3302 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Accel
- Bedienungsanleitungen 3302
- Produktkarten Accel
- Informationsbroschüren
- oder Energieetiketten Accel 3302
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Accel 3302.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Accel 3302, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Accel 3302. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Accel 3302 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Accel 3302, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Accel 3302 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Accel 3302 verständlich ist.

Eine gänzliche Bedienungsanleitung von Accel sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Accel 3302 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Accel 3302 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Accel 3302, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Accel 3302 - die uns die ersten Schritte während der Nutzung von Accel 3302 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Accel 3302 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Accel 3302 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Accel 3302?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Accel 3302 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Accel 3302 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)