Bedienungsanleitung Cisco Systems MEM-16F-RSP4+=

20 Seiten 0.31 mb
Download

Zur Seite of 20

Summary
  • Cisco Systems MEM-16F-RSP4+= - page 1

    Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 20 0 1 . Cisco Systems, Inc. All rights reserved. 78-12288-02 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide Product Numbers: MEM-16F-RSP4+= Customer Order Number: DOC-7812288= Introduction An 8 MB bootf lash ima ...

  • Cisco Systems MEM-16F-RSP4+= - page 2

    2 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Related Documentation • Conf irming the Bootf lash Memory Size, page 9 • Removing the RSP4+, page 9 • Removing the SIMM, page 11 • Installing the SIMM, page 13 • Installing the RSP4+, page 15 • Loading and Conf iguring the Bootf lash Image, page 15 ...

  • Cisco Systems MEM-16F-RSP4+= - page 3

    3 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installation Requirements Installation Requirements Before upgrading the bootf lash SIMM, pay attention to the follo wing sections: • Software and Bootf lash Prerequisites, page 3 • T ools and Parts Required, page 4 • Safety Guidelines, page 4 Software a ...

  • Cisco Systems MEM-16F-RSP4+= - page 4

    4 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installation Requirements Tools and Parts Required Y ou need the follo wing tools and parts to install or upgrade the bootf lash SIMM: • Number 1 Phillips and a 3/16-inch f lat-blade scre wdriv er • ESD-prev ention equipment or disposable grounding wrist s ...

  • Cisco Systems MEM-16F-RSP4+= - page 5

    5 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installation Requirements Attention Ce symbole d'avertissement indique un danger . V ous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par ...

  • Cisco Systems MEM-16F-RSP4+= - page 6

    6 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installation Requirements Installation Warning ¡Advertencia! Este símbolo de aviso signif ica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse ...

  • Cisco Systems MEM-16F-RSP4+= - page 7

    7 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installation Requirements Electrical Equipment Guidelines Follo w these basic guidelines when working with any electrical equipment: • Before beginning an y procedures requiring access to the router interior , locate the emergency power -of f switch for the ...

  • Cisco Systems MEM-16F-RSP4+= - page 8

    8 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installation Requirements Wrist Strap Warning Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Waarschuwing Draag tijd ...

  • Cisco Systems MEM-16F-RSP4+= - page 9

    9 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Overview Overview Bootf lash is a single inline memory module (SIMM) with a bootloader image that allo ws the router to access the Cisco IOS image when powering up or initializing the system. Bootloader images can be do wnloaded over the network, or from a loc ...

  • Cisco Systems MEM-16F-RSP4+= - page 10

    10 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Removing the RSP4+ Step 6 Use the RSP4+ handle to carefully pull it straight out of the slot, keeping your other hand under the carrier to guide it. (See Figure 2.) Keep the RSP4+ parallel to the backplane. A void touching the board or any connector pins. Ste ...

  • Cisco Systems MEM-16F-RSP4+= - page 11

    11 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Removing the SIMM Figur e 2 Handling the RSP4+ Dur ing Remov al and Installation This completes the RSP4+ remov al procedure. Removing the SIMM After removing the RSP4+ from the Cisco 7500 series router , remo ve the 8-MB SIMM, using the follo wing procedure. ...

  • Cisco Systems MEM-16F-RSP4+= - page 12

    12 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Removing the SIMM Figur e 3 Location of SIMM on the RSP4+ Step 2 Locate the SIMM. The SIMM occupies socket U1. (See Figure 3.) Step 3 Remov e the SIMM from its socket by pulling the locking spring clips on both sides outward and tilting the SIMM free of the c ...

  • Cisco Systems MEM-16F-RSP4+= - page 13

    13 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installing the SIMM Figur e 5 Handling a SIMM Caution T o prev ent ESD damage, handle the edges of the SIMM only; av oid touching the memory module, pins, or traces (the metal f inger s) along the socket edge. Step 5 Place the SIMM in an antistatic bag to pro ...

  • Cisco Systems MEM-16F-RSP4+= - page 14

    14 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installing the SIMM Note When inserting SIMMs, use f irm b ut not excessi ve pressure. If you damage a socket, you will hav e to return the RSP4+ to the factory for repair . Step 5 Gently push the SIMM into the socket until the spring clips snap ov er the end ...

  • Cisco Systems MEM-16F-RSP4+= - page 15

    15 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Installing the RSP4+ Installing the RSP4+ Follo w the steps below to reinstall the RSP4+ that w as removed. Step 1 Hold the RSP4+ handle with one hand and place your other hand under the carrier to support the RSP4+ and guide it into the slot. (See Figure 2.) ...

  • Cisco Systems MEM-16F-RSP4+= - page 16

    16 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Loading and Configuring the Bootflash Image Step 1 Boot the router , and allow it to initialize. Step 2 Use the enable command to enter privileged mode so you can conf igure the new 16MB bootf lash: Router> en Password: Router# Step 3 Use the show version ...

  • Cisco Systems MEM-16F-RSP4+= - page 17

    17 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Loading and Configuring the Bootflash Image Step 5 T o copy the rsp-boot image onto the bootf lash, use the following series of commands: Router# copy tftp:rsp-boot-mz.121-5.T1 bootflash:rsp-boot-mz.121-5.T1 20575008 bytes available on device slot0, proceed? ...

  • Cisco Systems MEM-16F-RSP4+= - page 18

    18 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Obtaining Documentation Step 11 Use the sh bootv command to conf irm that the new bootloader image will load automatically the ne xt time the system boots or reinitializes. Router#sh bootv BOOT variable = CONFIG_FILE variable = bootflash:startup-config BOOTLD ...

  • Cisco Systems MEM-16F-RSP4+= - page 19

    19 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Obtaining Technical Assistance Documentation Feedback If you are reading Cisco product documentation on the W orld W ide W eb, you can submit technical comments electronically . Click Feedback in the toolbar and select Documentation . After you complete the f ...

  • Cisco Systems MEM-16F-RSP4+= - page 20

    20 RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide 78-12288-02 Obtaining Technical Assistance Contacting TAC by Using the Cisco TAC Website If you hav e a priority lev el 3 (P3) or priority lev el 4 (P4) problem, contact T A C by going to the T A C website: http://www .cisco.com/tac P3 and P4 le vel problems are def ined ...

Produzent Cisco Systems Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Cisco Systems MEM-16F-RSP4+= erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco Systems
- Bedienungsanleitungen MEM-16F-RSP4+=
- Produktkarten Cisco Systems
- Informationsbroschüren
- oder Energieetiketten Cisco Systems MEM-16F-RSP4+=
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Systems MEM-16F-RSP4+=.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Systems MEM-16F-RSP4+=, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Systems MEM-16F-RSP4+=. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Systems MEM-16F-RSP4+= ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Systems MEM-16F-RSP4+=, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Systems MEM-16F-RSP4+= hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Systems MEM-16F-RSP4+= verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Systems MEM-16F-RSP4+= bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Systems MEM-16F-RSP4+= befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Systems MEM-16F-RSP4+=, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Systems MEM-16F-RSP4+= - die uns die ersten Schritte während der Nutzung von Cisco Systems MEM-16F-RSP4+= erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Systems MEM-16F-RSP4+= hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Systems MEM-16F-RSP4+= im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Systems MEM-16F-RSP4+=?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Systems MEM-16F-RSP4+= nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Systems MEM-16F-RSP4+= hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)