Deutsch dropdown-ico

Bedienungsanleitung Lincoln Electric 170I

45 Seiten 0.79 mb
Download

Zur Seite of 45

Summary
  • Lincoln Electric 170I - page 1

    Handymig 170i OPERA TOR’S MANUAL IM711 January, 2001 Safety Depends on You LiquidArc machines are designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thoughtful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READ- ING THIS MANUAL AND THE SAFETY PREC ...

  • Lincoln Electric 170I - page 2

    FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors. ________________________________________________ ...

  • Lincoln Electric 170I - page 3

    SAFETY 2.i.4 Connect the work cable to the work piece as close as possible to the area being welded. (This is also a good practice to eliminate a common problem on welding - a poor work connection. 2.i.5 Do not work next to the welding power source. ADDITIONAL PRECAUTIONS FOR WELDERS WITH PACEMAKERS 2.j. There is no question that the fields in arc ...

  • Lincoln Electric 170I - page 4

    iii SAFETY iii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 4.b. Use suitable clothing made from durable flame-resistant material to protect your sk ...

  • Lincoln Electric 170I - page 5

    FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the National Electrical Code, all local codes and the manufacturer ’ s recommendations. 8.c. Ground the equipment in accordance with the National Electrical Code and ...

  • Lincoln Electric 170I - page 6

    SAFETY v v INSTR UCTIONS FOR ELECTRO- MA GNETIC COMP A TIBILITY Conformance Products displaying the C-Tick mark are in conformity with Australian/New Zealand requirements for Electromagnetic Compatibility (EMC) according to standard (emission) AS/NZS 3652 "Electromagnetic Compatibility – Arc Welding Equipment". Products displaying the C ...

  • Lincoln Electric 170I - page 7

    Thank You for selecting a QUALITY product. We want you to take pride in operating this LiquidArc product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it handy for quick reference. Pay particular attention to the safety ins ...

  • Lincoln Electric 170I - page 8

    vii vii T ABLE OF CONTENTS Page Installation .......................................................................................................Section A Technical Specifications ........................................................................................A-1 Identify and Locate Components ............................................ ...

  • Lincoln Electric 170I - page 9

    viii viii T ABLE OF CONTENTS Page Learning to Weld (Continues) ......................................................................................------ Welding in a Vertical Position ........................................................................B-10 Vertical-up and Overhead Welding ..................................................... ...

  • Lincoln Electric 170I - page 10

    A-1 A-1 INST ALLA TION Fuse or Output Mode Input Voltage Breaker Size Input Amps Power Cord RATED 240V/50Hz 25 Super Lag 12.7 15Amp, 240V, Three Pin Plug TECHNICAL SPECIFICA TIONS – Hand ymig 170i INPUT – SINGLE PHASE ONL Y RA TED OUTPUT OUTPUT RECOMMENDED INPUT CABLE AND FUSE SIZES Height Width Depth Weight 305 mm 248 mm 419 mm 25.9 kg PHYSICA ...

  • Lincoln Electric 170I - page 11

    A-2 INST ALLA TION SAFETY PRECA UTIONS • Read entire installation section before starting installation. IDENTIFY AND LOCA TE COMPONENTS If you have not already done so, unpack the Handymig 170i from its carton and remove all packing material around the Handymig 170i. Remove the fol- lowing loose items from the carton (see Figure A.1): 1. Handymig ...

  • Lincoln Electric 170I - page 12

    A-3 INST ALLA TION SELECT SUIT ABLE LOCA TION Locate the welder in a dry location where there is free circulation of clean air into the louvers in the back and out the front of the unit. A location that minimizes the amount of smoke and dirt drawn into the rear louvers reduces the chance of dirt accumulation that can block air passages and cause ov ...

  • Lincoln Electric 170I - page 13

    A-4 A-4 INST ALLA TION W ork Cable Installation Refer to Figure A.2. 1. Open the wire feed section door on the right side of the Handymig 170i. 2. Pass the end of the work cable that has the termi- nal lug with the smaller hole through the Work Cable Access Hole (1) in the case front. 3. Route the cable under and around the back of the Wire Feed Ge ...

  • Lincoln Electric 170I - page 14

    A-5 INST ALLA TION BE SURE TO KEEP YOUR FACE AWAY FROM THE VALVE OUTLET WHEN “ CRACKING ” THE VALVE. Never stand directly in front of or behind the flow regulator when opening the cylinder valve. Always stand to one side. 3. Attach the flow regulator to the cylinder valve and tighten the union nut securely with a wrench.. 4. Refer to Figure A.6 ...

  • Lincoln Electric 170I - page 15

    A-6 INST ALLA TION ELECTRICAL INPUT CONNECTION FOR RA TED OUTPUT ELECTRIC SHOCK can kill. • Disconnect input power by removing plug from receptacle before working inside Handymig 170i. • Use only grounded receptacle. • Do not touch electrically “ hot ” parts inside Handymig 170i. • Have qualified personnel do the maintenance and trouble ...

  • Lincoln Electric 170I - page 16

    B-1 OPERA TION SAFETY PRECA UTIONS ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet clothing. Insulate yourself from work and ground. • Always wear dry insulating gloves. FUMES AND GASES can be dangerous. • Keep your head out of fumes. • Use ventilation or exhaust to remove fumes from breathing z ...

  • Lincoln Electric 170I - page 17

    B-2 B-2 OPERA TION WELDING CAP ABILITY The Handymig 170i is rated at 130 amps, 20 volts, at 20% duty cycle on a ten minute basis. It is capable of higher output currents at lower duty cycles. . LIMIT A TIONS Arc Gouging cannot be performed with the Handymig 170i. The Handymig 170i is not recommended for pipe thawing or TIG welding. CONTR OLS AND SE ...

  • Lincoln Electric 170I - page 18

    B-3 OPERA TION WELDING OPERA TIONS SEQUENCE OF OPERA TION Wire Loading Refer to Figure B.2 and B.3. The machine power switch should be turned to the OFF ( “ O ” ) position before working inside the wire feed enclosure. The machine is shipped from the factory ready to feed 8 ” (200 mm) diameter spools [2.2 ” (56 mm) max. width]. These spools ...

  • Lincoln Electric 170I - page 19

    B-4 B-4 OPERA TION Wire Threading Refer to Figure B.4 1 . Release the Spring Loaded Pressure Arm (1) rotate the Idle Roll Arm (2) away from the Wire Feed Drive Roll (3). Ensure that the groove size in the feeding position on the drive roll matches the wire size being used. See Maintenance section for further information. 2 . Carefully detach the en ...

  • Lincoln Electric 170I - page 20

    B-5 B-5 OPERA TION Making A Weld 1. See “ Process Guidelines ” in this section for selec- tion of welding wire and shielding gas and for range of metal thicknesses that can be welded. 2. See the Application chart on the inside of the wire feed compartment door for information on setting the Handymig 170i controls. Refer to Table B.1 for aluminu ...

  • Lincoln Electric 170I - page 21

    B-6 B-6 OPERA TION The Handymig 170i is suitable for .035"(0.9mm) alu- minum wire and .023" – .035"(0.6-0.9mm) stainless wire. Refer to Table B.1 for recommended procedure settings. (Requires K664-2 Aluminum - Stainless Feeding Kit.) It is important when changing between welding with steel wire and aluminum to exchange feeding comp ...

  • Lincoln Electric 170I - page 22

    Fumes and slag generated from Innershield type electrodes recom- mended for use with this welding machine can be toxic. • Avoid contact with eyes and skin. • Do not take internally. • Keep out of reach of children. • Follow all safety precautions found in this operating manual. B-7 B-7 LEARNING T O WELD W ARNING Electronic Components Hinges ...

  • Lincoln Electric 170I - page 23

    B-8 B-8 LEARNING T O WELD THE SELF-SHIELDED FCA W WELDING ARC Figure B.9 illustrates the action taking place in the self shielded FCAW (Innershield) welding arc. It closely resembles what is actually seen while welding. FIGURE B.9 The “ arc stream ” is seen in the middle of the picture. This is the electric arc created by the electric current f ...

  • Lincoln Electric 170I - page 24

    B-9 B-9 LEARNING T O WELD PROCESS SELECTION By gaining knowledge of the differences between the two processes, you will be able to select the best process for the job you have at hand. In selecting a process, you should consider: For GMAW (MIG) Process 1. Is most of my welding performed on 16 gauge and lighter materials? 2. Can I afford the extra e ...

  • Lincoln Electric 170I - page 25

    B-10 B-10 LEARNING T O WELD FIGURE B.12 Penetration Unless a weld penetrates close to 100% of the metal thickness, a butt weld will be weaker than the material welded together. In the example shown in Figure B.13, the total weld is only half the thickness of the material thus the weld is only approximately half as strong as the metal. FIGURE B.13 F ...

  • Lincoln Electric 170I - page 26

    B-11 B-11 LEARNING T O WELD FIGURE B.16 Vertical-down Welding Refer to Figure B.17 Vertical-down welds are applied at a fast pace. These welds are therefore shallow and narrow and, as such, are excellent for sheet metal. Vertical-down welds may be applied to 5/32 ” (3.9 mm) and lighter material. Use stringer beads and tip the gun in the direction ...

  • Lincoln Electric 170I - page 27

    B-12 B-12 LEARNING T O WELD ARC RAYS can burn eyes and skin. When using an open arc process, it Is necessary to use correct eye, head and body protection. Protect yourself and others, read “ ARC RAYS can burn ” at the front of this manual. • The Correct Way To Strike An Arc • Be sure the work clamp makes good electrical contact to the work. ...

  • Lincoln Electric 170I - page 28

    B-13 B-13 LEARNING T O WELD Mild Steel 16 gauge or 1/16 inch (1.6 mm) Electrode 0.035" (0.9 mm) Steelcore 71T-GS Innershield Wire Voltage Setting “ V ” A Wire Feed Speed “ o|o ” 1.5 For the Handymig 170i, use the following: Helpful Hints • For general welding, it is not necessary to weave the arc, neither forward or backward nor side ...

  • Lincoln Electric 170I - page 29

    B-14 B-14 LEARNING T O WELD MA CHINE SET UP FOR THE GMA W (MIG) PROCESS • See PROCESS GUIDELINES in the OPERATION section for selection of welding wire and shielding gas, and for range of metal thicknesses that can be welded. • See the Application Guide on the inside of wire feed section door for information on setting the controls. • Set the ...

  • Lincoln Electric 170I - page 30

    Helpful Hints • For general welding, it is not necessary to weave the arc, neither forward or backward nor sideways. Weld along at a steady pace. You will find it easier. • When welding on thin plate, you will find that you will have to increase the welding speed, whereas when welding on heavy plate, it is necessary to go more slowly in order t ...

  • Lincoln Electric 170I - page 31

    B-16 B-16 LEARNING T O WELD • After you strike the arc, practice the correct electri- cal stickout. Learn to distinguish it by its sound. • When you are sure that you can hold the correct electrical stickout, with a smooth “ crackling ” arc, start moving. Look at the molten puddle constantly, • Run beads on a flat plate. Run them parallel ...

  • Lincoln Electric 170I - page 32

    B-17 B-17 LEARNING T O WELD Proper Gun Handling Most feeding problems are caused by improper han- dling of the gun cable or electrodes. • Do not kink or pull the gun around sharp corners • Keep the gun cable as straight as practical when welding. • Do not allow dolly wheels or trucks to run over the cables. • Keep the cable clean. • Inner ...

  • Lincoln Electric 170I - page 33

    B-18 B-18 APPLICA TION CHART Handymig 170i ...

  • Lincoln Electric 170I - page 34

    D-1 GUN AND CABLE MAINTENANCE FOR MA GNUM ™ 100L GUN Gun Cable Cleaning Clean cable liner after using approximately 300 lbs (136 kg) of solid wire or 50 lbs (23 kg) of flux-cored wire. Remove the cable from the wire feeder and lay it out straight on the floor. Remove the contact tip from the gun. Using low pressure air, gently blow out the cable ...

  • Lincoln Electric 170I - page 35

    D-2 D-2 MAINTENANCE COMPONENT REPLA CEMENT PR OCEDURES CHANGING THE CONT A CT TIP 1. Refer to Figure D.2. Remove the gas nozzle from the gun by unscrewing counter-clockwise. 2. Remove the existing contact tip from the gun by unscrewing counter-clockwise. 3. Insert and hand tighten desired contact tip. 4. Replace gas nozzle. CHANGING DRIVE ROLL The ...

  • Lincoln Electric 170I - page 36

    GUN HANDLE P AR TS The gun handle consists of two halves that are held together with a collar on each end. To open up the handle, turn the collars approximately 60 degrees counter-clockwise until the collar reaches a stop. Then pull the collar off the gun handle. If the collars are diffi- cult to turn, position the gun handle against a corner, plac ...

  • Lincoln Electric 170I - page 37

    D-4 D-4 GR OUND TEST PROCEDURE WARNING ELECTRIC SHOCK can kill WARNING: This procedure is only suitable for applica- tions using DC mega testers up to 500V. Note: This procedure is for ‘ machines as built ’ many modifications could have taken place over the life of a particular machine, so details of this procedure may need to be ‘ adjusted ? ...

  • Lincoln Electric 170I - page 38

    E-1 E-1 TR OUBLESHOO TING This Troubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow the three-step procedure listed below. Step 1. LOCATE PROBLEM (SYMPTOM). Look under the column labeled “ PROBLEM (SYMPTOMS) ” . This column describes pos- sible symptoms that the machine may exhibit. Find t ...

  • Lincoln Electric 170I - page 39

    E-2 E-2 TR OUBLESHOO TING Observe Safety Guidelines detailed in the beginning of this manual. TR OUBLESHOO TING GUIDE PROBLEMS (SYMPT OMS) Major physical or electrical damage is evident. No wire feed, weld output or gas flow when gun trigger is pulled. Fan does NOT operate. No wire feed, weld output or gas flow when gun trigger is pulled Fan operat ...

  • Lincoln Electric 170I - page 40

    E-3 E-3 TR OUBLESHOO TING TR OUBLESHOO TING GUIDE Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPT OMS) No wire feed when gun trigger is pulled. Fan runs, gas flows and machine has correct open circuit voltage (33 vcd maximum) – weld output. POSSIBLE AREAS OF MISADJUSTMENT(S) 1. If the wire drive motor is runnin ...

  • Lincoln Electric 170I - page 41

    E-4 E-4 TR OUBLESHOO TING Observe Safety Guidelines detailed in the beginning of this manual. TR OUBLESHOO TING GUIDE If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your LOCAL AUTHORIZED LIQUID ARC FIELD SERVICE FACILITY for assistance before you proceed. CA UTION PROBLEMS (SYM ...

  • Lincoln Electric 170I - page 42

    F-1 F-1 WIRING DIA GRAMS Handymig 170i WIRING DIA GRAM: Code 10842 Handymig 170i WIRING DIA GRAM 10/00 NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. Handymig 170i ...

  • Lincoln Electric 170I - page 43

    W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES. SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL F ABRICANTE P ARA E ...

  • Lincoln Electric 170I - page 44

    W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR. ● Keep your head out of fumes. ● Use ventilation or exhaust to remove fumes ...

  • Lincoln Electric 170I - page 45

    A Division of Lincoln Electric Company (Aust) Ply Ltd A.B.N. 36 000 040 308 Copyright © 2000 Lincoln Global Inc. 35 Bryant Street, Padstow, NSW2211, Australia ...

Produzent Lincoln Electric Kategorie Welder

Dokumente, die wir vom Produzenten des Geräts Lincoln Electric 170I erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Lincoln Electric
- Bedienungsanleitungen 170I
- Produktkarten Lincoln Electric
- Informationsbroschüren
- oder Energieetiketten Lincoln Electric 170I
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Lincoln Electric 170I.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Lincoln Electric 170I, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Lincoln Electric 170I. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Lincoln Electric 170I ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Lincoln Electric 170I, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Lincoln Electric 170I hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Lincoln Electric 170I verständlich ist.

Eine gänzliche Bedienungsanleitung von Lincoln Electric sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Lincoln Electric 170I bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Lincoln Electric 170I befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Lincoln Electric 170I, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Lincoln Electric 170I - die uns die ersten Schritte während der Nutzung von Lincoln Electric 170I erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Lincoln Electric 170I hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Lincoln Electric 170I im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Lincoln Electric 170I?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Lincoln Electric 170I nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Lincoln Electric 170I hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)