Bedienungsanleitung GE Ventila

12 Seiten 0.24 mb
Download

Zur Seite of 12

Summary
  • GE Ventila - page 1

    Use and Care of Recirculation Hood Models JN322, JN334, JN335, JMW, & JN635 and Ventilating Hood Models JV322, JV324, JV332, JV334, JV335, JV624, JV634, & JV635 — IMPORTANT SAFETY C. When cutting or drilling into wall or ceiling, INSTRUCTIONS do not damage electrical wiring and other hidden utilities. WARNING- TO REDUCE THE RISK D. Ducted ...

  • GE Ventila - page 2

    2 If You Need Service... ● Do not attempt to repair or replace any part of 1 your hood unless it is speciikxdly recommended in this book. All other servicing should be referred to a qualified technician. ● Disconnect hood circuit breaker or fuse before performing any service. IMPORTANT SAFETY INSTRUCTIONS {continu~) WARNING TO REDUCE THE RISK O ...

  • GE Ventila - page 3

    To Operate —Vents (“JN” models only) Lamp switch Fan switch Trim Lamp Switch Models: JN322, JV322 & JV332 Press for OFF and ON. Lamp Stitch All other models. CENTER position OFF, LE~ position NIGHT LIGHT, RIGHT position BRIGHT LIGHT. Fan Switch CENTER position OFF, LEFT position LOW SPEED, RIGHT position HIGH SPEED. To Maintain Replaceabl ...

  • GE Ventila - page 4

    Installation Instructions for General Electric Hood Models: JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635 Important-save for the local electrical inspector% use Power supply connection box on underside of hood. I 7%” ~pe “C” Y~ models Exhaust Outlet Knockouts — 4 ...

  • GE Ventila - page 5

    1. PREPARATION OF WALL CABINET AND WALL FLUSH OR RECESSED BOITOM CABINET NOTE: For easier installation make all hood and vent cutouts in the cabinet and wall before cabinet is permanently fastened in place. It is recommended that the power supply be brought into the hood from the wall below the cabinet as shown in Fig. 1. However, an optional locat ...

  • GE Ventila - page 6

    2. DUCT INSTALLATION T@e “B” Models: See Figs. 4 and 9. The hood exhaust has been designed to mate with standard 7“ round duct. (A round damper kit may be ordered. Order GE model number JXDA22.)* A. If a rectangular duct is desired, a round-to-rectangular adapter must be used. Install a 4“ minimum length of 7“ round duct between the hood ...

  • GE Ventila - page 7

    3. POWER SUPPLY A. CIRCUIT VOLTAGE: This hood must be connected to a supply circuit of the proper voltage and frequency as specified on the rating plate. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for hoods of this rating. The rating plate is located on the rear wall of the hood. B. FUSE ...

  • GE Ventila - page 8

    IMPORTANT: After installation, peel off the transparent protective film stripping from the decorative trim on the front of the hood. (See Fig. 12.) B. ELECTRICAL CONNECTION 1. Be sure the power supply is disconnected before making electrical connections. 2. Remove the connection box cover located on the left side of the fan unit. 3. Attach the powe ...

  • GE Ventila - page 9

    Lamp Replacement Remove the lamp and replace with an ordinary screw- base lamp bulb NOT MORE THAN 60 WATTS. Models JN334, JN335, JN634, To remove the lamp cover, if desired: JN635, JV324, JV334, JV335, ● Press the sides with 2 fingers until the side prongs JV624, JV634, JV635 have a are released. lamp cover. ● Lift the lamp cover and slide towa ...

  • GE Ventila - page 10

    Questions? Use This Problem Solver PROBLEM POSSIBLE CAUSE FAN DOES NOT ● A fuse may be blown or a circuit breaker tripped. Replace fuse or reset circuit breaker. OPERATE WHEN THE SWITCH IS ON FAN FAILS TO . Fan blade striking the hcmd sheI1. CIRCULATE AIR s Excessively soiled filter should be checked and corrected before using the hood again. FAN ...

  • GE Ventila - page 11

    Help Us Help You... Write down the model and serial numbers. You’ll find them on a label on the back wall of the hood. These numbers are also on the Consumer Product Ownership Registration Card that came with your hood. Before sending in this card, please write these numbers here: Model Number Serial Number Use these numbers in any correspondence ...

  • GE Ventila - page 12

    YOUR RANGE HOOD Staple sales slip or cancelled check WARRANTY here. Proof of original purchase date is needed to obtain service I — under warranty. WHAT IS COVERED FULL ONE-YEAR WARRANTY For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any part of the hood that ...

Produzent GE Kategorie Ventilation Hood

Dokumente, die wir vom Produzenten des Geräts GE Ventila erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen GE
- Bedienungsanleitungen Ventila
- Produktkarten GE
- Informationsbroschüren
- oder Energieetiketten GE Ventila
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung GE Ventila.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen GE Ventila, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen GE Ventila. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts GE Ventila ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts GE Ventila, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von GE Ventila hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von GE Ventila verständlich ist.

Eine gänzliche Bedienungsanleitung von GE sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von GE Ventila bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von GE Ventila befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich GE Ventila, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts GE Ventila - die uns die ersten Schritte während der Nutzung von GE Ventila erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit GE Ventila hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von GE Ventila im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich GE Ventila?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit GE Ventila nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit GE Ventila hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)