Deutsch dropdown-ico

Bedienungsanleitung POSline ITT4300B

46 Seiten Betrifft nicht
Download

Zur Seite of 46

Summary
  • POSline ITT4300B - page 1

    ITT4300 Label Printer ...

  • POSline ITT4300B - page 2

    CONTENTS Checking Your Box ............................................................................... 3 Power Supply ........................................................................................ 5 Parts and Features ................................................................................ 7 Loading the Ribbon ................ ...

  • POSline ITT4300B - page 3

    POSline ITT4300 Label Printer 3 Checking Your Box Receiving the box of your printer, you are advised to check first for the possible shipping damage. There are two ways you can do it: 1. Inspect the outer appearances of both the box and the printer for possible damage. 2. Raise the top cover of the printer to see if the media compartments are in or ...

  • POSline ITT4300B - page 4

    POSline ITT4300 Label Printer 4 ...

  • POSline ITT4300B - page 5

    POSline ITT4300 Label Printer 5 Power Supply Setting up the Printer Before setting up the printer you should first consider the following: • Find a solid flat surface with adequate room for the printer. Make sure there is enough room on the top side for the media and ribbon access. • The location should be near the host or terminal. Consider th ...

  • POSline ITT4300B - page 6

    POSline ITT4300 Label Printer 6 ...

  • POSline ITT4300B - page 7

    POSline ITT4300 Label Printer 6 Parts and Features Front Access Door ...

  • POSline ITT4300B - page 8

    POSline ITT4300 Label Printer 6 ...

  • POSline ITT4300B - page 9

    POSline ITT4300 Label Printer 6 Loading the Ribbon Notes: 1. This section is applicable to the transfer thermal printing. 2. Attached ribbon is coating inside. 1. Lift the top access door and the front access door to expose the compartment. ( Figure 1 ) 2. Push the head latch by anti-clockwise, and then fold the bracket. ( Figure 2 ) 3. Unwrap the ...

  • POSline ITT4300B - page 10

    POSline ITT4300 Label Printer 6 ...

  • POSline ITT4300B - page 11

    POSline ITT4300 Label Printer 6 ...

  • POSline ITT4300B - page 12

    POSline ITT4300 Label Printer 6 Loading the Media The ITT4300 printers can be operated in three different options: standard, peel-off, or with a cutter. • Standard mode allows you to collect each label freely. • In peel-off mode, the backing material is being peeled away from the label as it is printed. After the former label is removed, the ne ...

  • POSline ITT4300B - page 13

    POSline ITT4300 Label Printer 6 ...

  • POSline ITT4300B - page 14

    POSline ITT4300 Label Printer 6 ...

  • POSline ITT4300B - page 15

    POSline ITT4300 Label Printer 6 10 ...

  • POSline ITT4300B - page 16

    POSline ITT4300 Label Printer 6 Operator Controls Front Panel The front panel includes - 3 LED indicators (READY, MEDIA and RIBBON) - 3 buttons (FEED, PAUSE and CANCEL) ...

  • POSline ITT4300B - page 17

    POSline ITT4300 Label Printer 6 LED Indicators There are three LED indicators on the front panel, “READY”, “MEDIA” and “RIBBON”. These indicators display the operation status of the printer. • READY The READY indicator will remain lighted except if any of the following conditions prevail. - The printer is at PAUSE state. - A fault con ...

  • POSline ITT4300B - page 18

    POSline ITT4300 Label Printer 6 Buttons There are three buttons, each having two basic functions. Button Under normal condition Pressed the button and turn on the power simultaneously FEED Feeds a label. Performs a self test and a configuration report will be printed. PAUSE • Stops the printing process. • Resume the printing after press it agai ...

  • POSline ITT4300B - page 19

    POSline ITT4300 Label Printer 6 There is a power slide switch for voltage selection. Set correct voltage (115V or 230V) otherwise the printer will be damaged. ...

  • POSline ITT4300B - page 20

    POSline ITT4300 Label Printer 6 Performing Calibration After the media and label are loaded, it is necessary to do the calibration for the label sensor. 1. Press and hold the PAUSE button. 2. Turn on the power. 3. The printer will feed the labels for 12 inches. 4. Finally the “READY” message is displayed, the READY and MEDIA indicators stop bli ...

  • POSline ITT4300B - page 21

    POSline ITT4300 Label Printer 6 Printing Configuration Report Performing the Self Test 1. Turn off the printer. Press and hold the FEED button. 2. Turn on the power. 3. When the message “SELF TESTING …” is displayed on the LCD and READY indicator blinks, release the button. 4. The printer will print out a configuration report. 5. Finally the ...

  • POSline ITT4300B - page 22

    POSline ITT4300 Label Printer 6 Resetting the Printer to Factory Default Settings If you would like to reset the printer to its factory defaults after certain commands have been sent or settings changed: 1. Turn off the printer. Press and hold the CANCEL button. 2. Turn on the power. 3. When the message “E2PROM RESET …” is displayed on the LC ...

  • POSline ITT4300B - page 23

    POSline ITT4300 Label Printer 6 Hooking up the Printer & Computer Connecting the Printer to Your Host 1. You can connect the printer with any standard Centronics cable to the parallel port of the host computer. 2. Alternatively you can connect the printer with a serial cable to the RS232C port of your computer or terminal. (for PC compatibles, ...

  • POSline ITT4300B - page 24

    POSline ITT4300 Label Printer 6 Communicate with the Printer The bundled printer driver can be applied to all the applications under Windows 2000/ 98/95, Me, Windows NT and XP. Through this driver you may run any popular software applications e.g. MS- Word and print out the contents by this label printer as long as they are for Windows. Before inst ...

  • POSline ITT4300B - page 25

    POSline ITT4300 Label Printer 6 Installing Driver Note: Before installation, please make sure your “user’s right” is up to the level of ‘Administrator'. 1. Click the “Start” button. 2. Select “Setting”, then select “Printers” and double click the “Add Printer” icon. Click “Next”. 3. Click the “Network” or “Loc ...

  • POSline ITT4300B - page 26

    POSline ITT4300 Label Printer 6 Set the Parameters After installing the driver, you can follow the path below to set parameters: Start à Settings à Printers à Label Dr. à Properties The parameters include: Ports Select the IO port to link with the printer. The port may be one of parallel (LPT), serial (COM), net work port or file. Paper size Se ...

  • POSline ITT4300B - page 27

    POSline ITT4300 Label Printer 6 For Win 98 • Ports Properties menu à click “Details” à select the IO port à click “OK” • Paper size • Orientation • Paper source (Media type) • Media choice (Darkness) Copies Properties menu à click "Paper" à click each item to à select desired parameter à click "OK". • ...

  • POSline ITT4300B - page 28

    POSline ITT4300 Label Printer 6 Properties menu à click "Paper" à click "more option" à select Enable/ without cutter, peeler à click "OK" • Print quality (Speed) Properties menu à click "Device Options" à select parameters à click "OK" ...

  • POSline ITT4300B - page 29

    POSline ITT4300 Label Printer 6 • Create User-Define Paper Properties menu à click "Paper" à select "Custom" à User-Define size à set up a new size à click "OK" ...

  • POSline ITT4300B - page 30

    POSline ITT4300 Label Printer 6 For Win 2000 • Ports Properties menu à click "Ports" à select the IO port à click "OK" • Paper source (Media type) Back to Printers menu à Label Dr. à right click to get pop- up menu à select "Printing Reference" à click "Paper Quality" à select media type à click ...

  • POSline ITT4300B - page 31

    POSline ITT4300 Label Printer 6 • Orientation Printing Reference menu à click "Layout" à select "Portrait" or "Landscape" à click "OK" • Paper size • Copies • Media choice (Accessory setting) • Paper/ Output (Speed) • Print quality (Darkness) Printing Reference menu à click "Layout" ...

  • POSline ITT4300B - page 32

    POSline ITT4300 Label Printer 6 • Create a new size Printer menu à right click to get pop- up menu in blank space à select "Server Properties" à enter a form name for the new form in "Form description for" à reset the paper size in the specific squares of the "Measurements" à click "OK" ...

  • POSline ITT4300B - page 33

    POSline ITT4300 Label Printer 6 For NT 4.0 and XP • Ports Properties menu à click "Ports" à select the IO port à click "OK" • Paper size • Orientation • Paper source (Media type) • Copies • Media choice (Accessory setting) Printers menu à Label Dr. à right click to get pop-up menu à select "Document Defaul ...

  • POSline ITT4300B - page 34

    POSline ITT4300 Label Printer 6 • Paper/Output (Speed) • Print quality (Darkness) Default Document menu à click "Advanced" à click each item to select desired parameter à click "OK" • Create a new size Please refer to the procedure of create a new size on Win 2000. ...

  • POSline ITT4300B - page 35

    POSline ITT4300 Label Printer 6 Troubleshooting Generally, when a malfunction or an abnormal condition occurs, the “READY” LED will keep blinking and printing and communication between the host and printer will stop. To understand what the problem, please check the LEDs first: A. Problems on media Blinking Indicators READYand MEDIA LCD display ...

  • POSline ITT4300B - page 36

    POSline ITT4300 Label Printer 6 B. Problems on ribbon Blinking Indicators READYand MEDIA LCD display MEDIA OUT Possible Problems Solutions Remarks Ribbons has run out Supply the ribbon roll Does not apply to direct thermal. If you use direct thermal, set bit 1 of DIP switch to OFF. Ribbon jam Recover the jam not for direct thermal. Ribbon sensor er ...

  • POSline ITT4300B - page 37

    POSline ITT4300 Label Printer 6 D. Miscellaneous • The host shows “Printer Time out”. 1. Is the communication cable (parallel or serial) connected securely to your parallel or serial port on the PC and to the connector on the printer ? 2. Is the printer power turned on ? If the power cord is connected, the power switch is at position ‘1’ ...

  • POSline ITT4300B - page 38

    POSline ITT4300 Label Printer 6 . Adjust the Darkness (heat temperature). . Slow down the print speed. . Refer to the following paragraphs and clear the related modules. Recovery In order to continue your print jobs after any abnormal conditions have been recovered, simply press the CANCEL button or restart the printer. Make sure that the LED indic ...

  • POSline ITT4300B - page 39

    POSline ITT4300 Label Printer 6 Caring for your Printer Before maintenance be sure to turn off the printer power. 1. Cleaning the print head( TPH) Turn off the printer, open the cover, print head module and remove the ribbon. Rub the print head with a piece of cotton which has been moistened with alcohol. Check for any traces of black coloring or a ...

  • POSline ITT4300B - page 40

    POSline ITT4300 Label Printer 6 Reference Technical Information 1. General Specification Specification Model ITT4300 Print method Direct thermal and thermal transfer Resolution 203 DPI (8 dots/mm) Printing width 0.1”~ 4.09” (25 ~104 mm) Printing length 0.5”~ 45” (13 ~1143 mm) Printing speed 2~ 4 ips (51~ 104 mm/ s) Memory 512K bytes DRAM 51 ...

  • POSline ITT4300B - page 41

    POSline ITT4300 Label Printer 6 2. Fonts, Bar Codes and Graphics Specification The specifications of fonts, bar codes and graphics depend on the printer emulation. The emulation is a printer programming language, through which the host can communicate with your printer. There are two printer programming, they are PPLA and PPLB. Printer Programming ...

  • POSline ITT4300B - page 42

    POSline ITT4300 Label Printer 6 Printer Programming Language B, PPLB Specification Model ITT4300 General fonts 5 fonts with different point sizes Symbol sets (Code pages) 8 bits: code page 437, 850, 852, 860, 863 and 865. 7 bits: USA, British, German, French, Danish, Italian, Spanish, Swedish and Swiss. Soft fonts Downloadable soft fonts Font expan ...

  • POSline ITT4300B - page 43

    POSline ITT4300 Label Printer 6 3. Interface Specifications Introduction This appendix presents the interface specifications of IO ports for the printer. These specifications include pin assignments, protocols and detailed information about how to properly interface your printer with your host or terminal. Serial • The RS232 connector on the prin ...

  • POSline ITT4300B - page 44

    POSline ITT4300 Label Printer 6 Connection with host: Host 25S Printer 9P Host 9S Printer 9P (PC or compatible) (PC or compatible) DTR 20 ………..1 DSR DTR 4 ………..1 DSR DSR 6 ………..6 DTR DSR 6 ………..6 DTR TX 2 ………..2 RX TX 3 ………..2 RX RX 3 ………..3 TX RX 2 ………..3 TX CTS 5 ………..7 RTS CTS 8 ………..7 ...

  • POSline ITT4300B - page 45

    POSline ITT4300 Label Printer 6 Data format: always 8 data bits, 1 start bit and 1 stop bit. Parity: always non parity Handshaking: XON/ XOFF as well as CTS/ RTS (hardware flow control). If you run an application with the bundled printer driver under Windows and use the serial port, you should check the above parameters and set the flow control to ...

  • POSline ITT4300B - page 46

    POSline ITT4300 Label Printer 6 4. ASCII TABLE 0 1 2 3 4 5 6 7 0 NUL 0 @ P ` P 1 SOH XON ! 1 A Q a Q 2 STX “ 2 B R b R 3 XOFF # 3 C S c S 4 $ 4 D T d T 5 NAK % 5 E U e U 6 ACK & 6 F V f V 7 BEL ‘ 7 G W g W 8 BS ( 8 H X h X 9 ) 9 I Y i Y A LF * : J Z j Z B ESC + ; K [ k { C FF , < L l | D CR - = M ] m } E SO RS . > N ^ n ~ F SI US / ...

Produzent POSline Kategorie Label Printer

Dokumente, die wir vom Produzenten des Geräts POSline ITT4300B erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen POSline
- Bedienungsanleitungen ITT4300B
- Produktkarten POSline
- Informationsbroschüren
- oder Energieetiketten POSline ITT4300B
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung POSline ITT4300B.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen POSline ITT4300B, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen POSline ITT4300B. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts POSline ITT4300B ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts POSline ITT4300B, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von POSline ITT4300B hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von POSline ITT4300B verständlich ist.

Eine gänzliche Bedienungsanleitung von POSline sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von POSline ITT4300B bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von POSline ITT4300B befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich POSline ITT4300B, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts POSline ITT4300B - die uns die ersten Schritte während der Nutzung von POSline ITT4300B erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit POSline ITT4300B hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von POSline ITT4300B im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich POSline ITT4300B?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit POSline ITT4300B nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit POSline ITT4300B hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)