Bedienungsanleitung Stanley Black & Decker PR41

20 Seiten 1.53 mb
Download

Zur Seite of 20

Summary
  • Stanley Black & Decker PR41 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 32472 8/2014 V er . 5 USER MANUAL Safety , Operation and Maintenance PR41 HYDRAULIC PRUNER ...

  • Stanley Black & Decker PR41 - page 2

    ...

  • Stanley Black & Decker PR41 - page 3

    PR41 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer . Please read the following warning. For the nearest authorized and certie ...

  • Stanley Black & Decker PR41 - page 4

    4 ► PR41 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker PR41 - page 5

    PR41 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs. ...

  • Stanley Black & Decker PR41 - page 6

    6 ► PR41 User Manual The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (ref. ANSI Z133.1-2000) WORKING IN PROXIMITY T O ELECTRICAL HAZARDS An inspection shall be made by a qualied arborist to determine whether an electrical hazard exists before cli ...

  • Stanley Black & Decker PR41 - page 7

    PR41 User Manual ◄ 7 T able 2 – Minimum approach distances to energized conductors for persons other than qualied line- clearance arborists and qualied line- clearance arborist trainees. Nominal V oltage kV phase-to-phase 1 Distance ft-in m 0.0 – 1.0 10–00 3.05 1.1 – 15.0 10–00 3.05 15.1 – 36.0 10–00 3.05 36.1 – 50.0 10–00 ...

  • Stanley Black & Decker PR41 - page 8

    8 ► PR41 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA TOR. SEE OTHER SIDE 1. FAILURE TO USE H ...

  • Stanley Black & Decker PR41 - page 9

    PR41 User Manual ◄ 9 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker PR41 - page 10

    10 ► PR41 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS 4-6 ...

  • Stanley Black & Decker PR41 - page 11

    PR41 User Manual ◄ 1 1 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacit ...

  • Stanley Black & Decker PR41 - page 12

    12 ► PR41 User Manual PREP ARA TION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required. After instal- lation of hoses and couplers a unit may be put to use. CHECK HYDRAULIC P ...

  • Stanley Black & Decker PR41 - page 13

    PR41 User Manual ◄ 13 LA TERAL BRANCH BRANCH T O BE CUT BLADE T OWARDS LA TERAL BRANCH WILL LEA VE EDGE FLUSH WITH LA TERAL BRANCH NO STUB LEFT Figure 2. Example of Lateral Branch Cut WARNING The following are general wood cutting procedures and techniques. Differences in the terrain, vegetation, and type of wood will make this information more o ...

  • Stanley Black & Decker PR41 - page 14

    14 ► PR41 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hydrau- lic system. • Always store the tool in a clean dry ...

  • Stanley Black & Decker PR41 - page 15

    PR41 User Manual ◄ 15 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the tool, always make sure the hydraulic power source is supplying the cor - rect hydraulic ow and pressure as listed in the table. Use a owmeter know to be accurate. Check ...

  • Stanley Black & Decker PR41 - page 16

    16 ► PR41 User Manual Capacity......................................................................................................................................2-1/4 inch/5.7 cm cut Pressure Range ................................................................................................................ 1000–2000 psi/70–140 bar Maxim ...

  • Stanley Black & Decker PR41 - page 17

    PR41 User Manual ◄ 17 PR41 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker PR41 - page 18

    18 ► PR41 User Manual ITEM P ART NO. QTY DESCRIPTION 44 28502 1 NAME T AG 45 25910 1 NOTICE STICKER 46 51 183 1 TRIGGER 47 05268 1 HEX SLOTTED NUT 03693 1 CLOSED CENTER DECAL (PR41231 ONL Y) 03972 1 FEMALE COUPLER (SUPPLIED W/ PR41 13103 ONL Y) 03973 1 MALE COUPLER (SUPPLIED W/ PR41 13103 ONL Y) 03971 1 COUPLER SET (PR41 1303 ONL Y) 32473 1 SEAL ...

  • Stanley Black & Decker PR41 - page 19

    ...

  • Stanley Black & Decker PR41 - page 20

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Produzent Stanley Black & Decker Kategorie Pole Saw

Dokumente, die wir vom Produzenten des Geräts Stanley Black & Decker PR41 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Stanley Black & Decker
- Bedienungsanleitungen PR41
- Produktkarten Stanley Black & Decker
- Informationsbroschüren
- oder Energieetiketten Stanley Black & Decker PR41
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Stanley Black & Decker PR41.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Stanley Black & Decker PR41, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Stanley Black & Decker PR41. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Stanley Black & Decker PR41 ansehen.

Die komplette Bedienungsanleitung des Geräts Stanley Black & Decker PR41, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Stanley Black & Decker PR41 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Stanley Black & Decker PR41 verständlich ist.

Eine gänzliche Bedienungsanleitung von Stanley Black & Decker sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Stanley Black & Decker PR41 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Stanley Black & Decker PR41 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Stanley Black & Decker PR41, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Stanley Black & Decker PR41 - die uns die ersten Schritte während der Nutzung von Stanley Black & Decker PR41 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Stanley Black & Decker PR41 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Stanley Black & Decker PR41 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Stanley Black & Decker PR41?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Stanley Black & Decker PR41 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Stanley Black & Decker PR41 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)