-
Miele DA 229-2 - page 1
Operating and installation instructions V entilation System D A 229-2 T o pr event accidents V and machine damage, read these instructions before installation or use. M.-Nr . 05 603 730 ...
-
Miele DA 229-2 - page 2
W arning and Safety instructions Guide to the appliance Functional description Operation Main power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 T urning on the fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Selecting the power ...
-
Miele DA 229-2 - page 3
Read these Operating Instructions carefully bef ore installing or using the V entilation System. This appliance is intended for resi - dential use only . Use the appliance only for its intended purpose. The manufacturer cannot be held r e - sponsible for damages caused by improper use of the hood. This appliance complies with current safety requir ...
-
Miele DA 229-2 - page 4
This equipment is not designed for maritime use or for use in mobile installations such as caravans or air - craft. However , under certain conditions it may be possible for an installation in these applications. Please contact the nearest Miele dealer or the Miele T ech - nical Service Department with specific requir ements. Before servicing, disc ...
-
Miele DA 229-2 - page 5
Do not use an extension cord to connect the appliance to electricity . Extension cords do not guarantee the requir ed safety of the appliance, (e.g. danger of overheating). Do not install this hood over cooktops burning solid fuel. Any fittings, sealant, or materials used to install the ductwork must be made of approved non-flammable materials. Nev ...
-
Miele DA 229-2 - page 6
Guide to the appliance 6 ...
-
Miele DA 229-2 - page 7
Chimney e xtension Chimney Canopy Overhead lighting Main power s witch Grease filter Grease filter button The indicator below the grease filter button lights when the grease filters need to be cleaned. This button is also used: – to reset the gr ease filter timer after cleaning the grease filters (see "Cleaning and Care"). – to show h ...
-
Miele DA 229-2 - page 8
The ventilation hood works by air ex - traction. The air is drawn in and cleaned by the grease filters and di - rected outside. The hood comes equipped with a non-return flap . This flap automatically closes when the hood is turned off so that no exchange of outside air and room air can occur . When the hood is turned on, the air pressure of the ex ...
-
Miele DA 229-2 - page 9
Main power s witch Press the main power switch to "I". The fan and the lighting can now be oper - ated. If the appliance is not going to be used for a long period of time (e.g. while va - cationing) turn the appliance off by pressing the main power switch to "0". The next time it is turned on, the hood will operate at the level ...
-
Miele DA 229-2 - page 10
T urning off the fan ^ Press the On/Of f button to turn the fan off. The indicator goes out. A utomatic Safety Shut Off The fan will be turned off automatically 10 hours after the last button was acti - vated. The lighting however , will remain on. ^ Press the On/Of f button to turn the fan back on. T urning the lighting on / off The overhead light ...
-
Miele DA 229-2 - page 11
Grease filter timer A timer monitors the hours of fan opera - tion. The indicator for the grease filter will light after 30 hours of operation. The grease filters must then be cleaned. After the grease filters have been cleaned and put in place, the grease fil - ter timer must be reset. ^ T o do this, pr ess the grease filter but - ton for about 3 ...
-
Miele DA 229-2 - page 12
Reprogramming the grease filter timer The grease filter timer is pr eset to 30 hours. This time can be lengthened or shortened to 20, 30, 40 or 50 hours. – A time of 20 hours should be pro - grammed in kitchens with frequent pan or deep frying. – A time of 20 hours should also be programmed if the kitchen is only used occasionally . Otherwise g ...
-
Miele DA 229-2 - page 13
Before cleaning or servicing the hood, disconnect it from the power supply by either removing the fuse, unplugging it from the outlet or man - ually "tripping" the circuit br eaker . Cleaning the casing W arning: Never use abrasive clean - ers, scouring pads, steel wool or caustic (oven) cleaners on the hood. They will damage the surface. ...
-
Miele DA 229-2 - page 14
Grease filters The reusable metal gr ease filters re - move solid particles from the vented kitchen air (grease, dust, etc). The grease filters should be cleaned every 3-4 weeks or whenever the grease filter indicator lights. A dirty filter is a fire hazard. ^ T o r emove the grease filters pr ess the locking clips in towards the middle of the filt ...
-
Miele DA 229-2 - page 15
When putting the grease filters back make sure that the locking clips ar e vis - ible facing down towards the cooking surface. If a filter is incorrectly installed, insert a small screwdriver into the slit along its edge to disengage it from the casing. ^ After returning the grease filters, press the gr ease filter button for 3 seconds to reset the ...
-
Miele DA 229-2 - page 16
Changing the light bulb Before changing the light bulbs, dis - connect the hood from the power supply by either removing the fuse, unplugging it, or manually "tripping" the circuit br eaker . When in use halogen bulbs become extremely hot, and they can burn your hands. Do not attempt to change the bulbs until they have had sufficient time ...
-
Miele DA 229-2 - page 17
In the event of a fault which you cannot correct yourself please contact: – Y our Miele Dealer or – The Miele T echnical Service Department USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting the T echnical Service Department, please quote the model and serial number of your appliance. These are shown on ...
-
Miele DA 229-2 - page 18
18 ...
-
Miele DA 229-2 - page 19
Installation instr uctions ...
-
Miele DA 229-2 - page 20
Caring for the en vir onment Installation accessories Plyw ood backing Electrical data Appliance dimensions Installation Retaining plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Attaching the canopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Miele DA 229-2 - page 21
Disposal of packing material The cardboar d box and packing materi - als protect the appliance during ship - ping. They have been designed to be biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of childr en. Dan - ger of suffocation! Disposal of an old applia ...
-
Miele DA 229-2 - page 22
Installation accessories 22 ...
-
Miele DA 229-2 - page 23
a 2 protective shields prevent scratches to the chimney dur - ing installation. b 2 hose clips for securing the ducting. c 1 reducing collar for use with 5" (125 mm) exhaust ducting. d 1 non-return flap e Upper retaining plate B secures the chimney extension. f Middle retaining plate C for addi - tional stability of the chimney . g Lower retai ...
-
Miele DA 229-2 - page 24
The majority of the weight of the in - stalled ventilation system will be supported by retaining plate A. It must be firmly attached to the stud framing behind the drywall. If studs are not available in the r equired lo - cations, a plywood backing (min. 1 / 2 " (13 mm) thick) spanning at least two studs must be installed. Failure to adequatel ...
-
Miele DA 229-2 - page 25
All electrical work should be per - formed by a qualified electrician in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The manufactur er can not be held responsible for unautho - rized work. Ensure that power to the appliance is OFF while installation or ...
-
Miele DA 229-2 - page 26
Appliance dimensions 26 ...
-
Miele DA 229-2 - page 27
Do not install this exhaust hood over cooktops burning solid fuel. When installing the hood, make sure that the following minimum dis - tance ( S ) between the top of a Miele cooking surface and the bottom of the hood is: - 22" (55 cm) above electric cooktops - 26" (65 cm) above gas cooktops - 26" (65 cm) above an open grill For non- ...
-
Miele DA 229-2 - page 28
Retaining plates The ventilation system will be mounted to the wall through the use of r etaining plates. Plate A is installed first, followed by plate B. Plate C should ony be used if the distance between plate A and plate B is greater than 14 3 / 8 " (365 mm). Attaching the retaining plates to the wall ^ Before fitting the r etaining plate d ...
-
Miele DA 229-2 - page 29
Retaining plate A ^ Drill two 1 / 8 " (3 mm) holes, one at S + 3" (75 mm) and one at S + 15 3 / 4 " (400 mm) on the center line (see "Ap - pliance dimensions"). ^ Lightly secure r etaining plate A into position using 5 x 40 mm screws through the two holes and use the notches to align with the center line. ^ Drill 6 more 1 / ...
-
Miele DA 229-2 - page 30
Retaining plate B ^ Hold retaining plate B to the wall and push up until it is directly below the ceiling. Use the notches and the cen- ter line to align it horizontally . Mark the 2 drill holes on the wall. ^ Drill two 1 / 8 " (3 mm) holes into the wall. ^ Secure the r etaining plate with two 5 x 40 mm screws. Retaining plate C Retaining plat ...
-
Miele DA 229-2 - page 31
Attaching the canop y ^ Hang the canopy on the angled brackets on retaining plate A. ^ Secure the canopy with two scr ews 5 x 60 mm. Adjusting the canopy If the canopy is not perpendicular to the wall it can be adjusted. ^ Loosen the two securing screws, a . ^ Slightly loosen the adjusting screws, b . ^ Adjust the canopy so that it is level and per ...
-
Miele DA 229-2 - page 32
Inserting the non-return flap ^ If a non-return flap is not present in the venting system, the non-return flap supplied must be fitted into the exhaust connection on the motor . The flaps must open upwards. ^ The hood is designed for 6" (150 mm) exhaust ducting. If 5" (125 mm) ex- haust ducting is used the reducing collar must be fitted i ...
-
Miele DA 229-2 - page 33
Electrical connection Before connecting the appliance read the "W arning and Safety In - structions" and the "Electrical data" sections. ^ Plug the connectors on the canopy into the corresponding r eceptacles left and right of the motor assembly . Insert the 4 prong connector into the receptacle left of the motor assem - bly . I ...
-
Miele DA 229-2 - page 34
Attaching the chimne y extension The use of a chimney extension, allows the hood to be installed at various dis - tances from the ceiling. ^ Remove the protective foil fr om the chimney extension. ^ Bend the top hanging tabs 45 ° in- wards. This will make installing the chimney extension easier . Be careful of sharp edges. ^ Pull the chimney exten ...
-
Miele DA 229-2 - page 35
Attaching the chimne y ^ Remove the protective foil fr om the chimney . ^ Pull the chimney apart slightly and slide it over the chimney extension. Do this carefully to pr event scratch- ing the two pieces. ^ Slide the chimney down about 3 / 4 " (2 cm) into the canopy . ^ Align and adjust the chimney . ^ Remove the protective shields. ^ Secure ...
-
Miele DA 229-2 - page 36
Danger of toxic fumes. Gas cooking appliances release carbon monoxide that can be harm - ful or fatal if inhaled. The exhaust gases extracted b y the hood should be vented outside of the building onl y . Do not terminate the exhaust ducts in attics, garages, crawlspaces, etc. Please read and follow the "W arning and Safety Instructions" t ...
-
Miele DA 229-2 - page 37
Never connect an exhaust hood to an active chimney , dryer vent, vent flue, or room venting ductwork. Seek professional advice befor e connect - ing an exhaust hood vent to an exist - ing, inactive chimney or vent flue. Ductwork with a diameter of less than 6" (150 mm) should only be used when absolutely necessary . As duct diameter decreases, ...
-
Miele DA 229-2 - page 38
38 ...
-
Miele DA 229-2 - page 39
39 ...
-
Miele DA 229-2 - page 40
Alteration rights reserved / 000 CDN - 1801 This paper consists of cellulose which has been bleached without the use of chlorine. ...
Haben Sie eine Frage bezüglich Miele DA 229-2?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Miele DA 229-2 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Miele DA 229-2 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.