-
CDA WC460 - page 1
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshir e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu Passionate about style W C460 Int egr at ed Slimline Dishw asher Manual for Inst allation, Use and Maintenanc e ...
-
CDA WC460 - page 2
Contents 1 1. Safety and operati ng instructions ___________________________ 2 2. Installation an d hook-up ___________________________________ 5 3. Description of t he controls _________________________________ 9 4. Operating inst ructions ___________________________________ 14 5. Cleaning and maintenance _______________________________ 24 6. Trou ...
-
CDA WC460 - page 3
Safety instructions 2 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLI ANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULL Y READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED B Y A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGU ...
-
CDA WC460 - page 4
Safety instructions 3 OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWER CORD AFTER UNPLU GGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (LOCKS, DOORS, ETC.). THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT ( W ...
-
CDA WC460 - page 5
Safety instructions 4 LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK. NEVER LEAVE THE DISHWASHER DOOR OPEN; PEOPLE MIGHT TRIP OVER IT. DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE. KNI ...
-
CDA WC460 - page 6
Installation instructions 5 2. Inst allation and hook-up Remove the polystyrene bask et retainers. Position the appliance in the desired place of installation. The back or sides of the dish washer may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent o ...
-
CDA WC460 - page 7
Installation instructions 6 CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with ¾” gas thread, inserting the filter A supplied w ith the dishwasher. Take care to screw th e hose firmly into place with your h ands and then complete b y tightening about ¼ of a turn with pliers. In dishwasher s equipped with the ACQU ...
-
CDA WC460 - page 8
Installation instructions 7 2.2 Electrical connection and precaution s CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATIONS IN FORCE. THE PL ...
-
CDA WC460 - page 9
User instructions 8 FOR GREAT BRITAIN ONLY: THIS APPLIANCE MUST BE E ARTHED. Fuse replacemen t If the mains lead of this appl iance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S .T .A. ap proved fuse to BS 1362 type and proceed as follo ws: 1. Remove the fuse cover A and fuse B . 2. Fit replacement 13A ...
-
CDA WC460 - page 10
User instructions 9 3. Description of the controls 3.1 Upper panel All the dishwasher controls are gr ou ped on the upper panel. Switch-on, programming, switch-off etc. procedur es are onl y possible when the door is open. 1 ON/OFF BUTTO N Pressing this button energises the appliance. 2 SELECTED PROGRAM INDIC ATOR LIGHTS Illumination of this light ...
-
CDA WC460 - page 11
User instructions 10 After using the table to identify the most appr opriate washing program: • press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate; • keep pressing the PROGRAM SELECTION button (3) until the indicator light corresponding to the desir ed program illuminates; • close the door; after about 2&qu ...
-
CDA WC460 - page 12
User instructions 11 3.2 Washing programs Before starting a washing pro gram make sure that: • The water supply tap is open. • The correct amount of detergent has been added to the dispenser . • The baskets have been correctly lo ad ed . • The spray arms are abl e to rotate freely and without obstruction. • The dishwasher door is secur el ...
-
CDA WC460 - page 13
User instructions 12 CANCELLING THE CURRENT PROGRAM • To cancel the currentl y sele cted program, open the door and hol d down the PROGRAM SELECTION (3) button for a few seconds until the indicator lights for programs 4 and 5 illuminate simultaneously (the word "end" is displ ayed on the window). • Close the door. • After approximat ...
-
CDA WC460 - page 14
User instructions 13 If the door has to be opened while washing is in progress, the progr am will be interrupted. The relativ e light will keep flashing and a bee per will signal that the cycle has not been co mpleted. You must wait about 1 minute before closing the door to re start the program. When the doo r is closed the program will continue fr ...
-
CDA WC460 - page 15
User instructions 14 4. Operating instructions Once the dishwasher h as been correctly installed, prepare for us e as follows: • Adjust the water softening system; • Add the regenerating salt; • Add the rinse aid and deter ge nt. 4.1 Using the water softening system The amount of scale contain ed in the water (water hardness inde x) can cause ...
-
CDA WC460 - page 16
User instructions 15 • Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. • When necessary, refill the r ege nerating salt container before starting the washing progra m . In this w ay, the excess saline solution will be immediately remove d by the water; the prolonged presence of ...
-
CDA WC460 - page 17
User instructions 16 WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degr ees (°dF) SETTING 0 - 4 0 - 7 S etting N. 1 NO SALT 5 - 15 8 - 25 Setting N. 1 16 - 23 26 - 40 Setting N. 2 24 - 31 41 - 60 Setting N. 3 32 - 47 61 - 80 Setting N. 4 48 - 58 81 - 100 Setting N. 5 Contact your local w ater board for inform ation on the hardne ...
-
CDA WC460 - page 18
User instructions 17 ADDING THE RINSE AID The rinse aid he lps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatic all y added to the water during the final rinse c ycle, from the container situated on the inner side of the door. To add rinse aid: • Open the door. • Rotate the container cap anticlock ...
-
CDA WC460 - page 19
User instructions 18 ADDING THE DETERGENT To open the detergent dispenser cap, l ightly press the button P . Add the detergent and clos e the cap carefully. During the washing cycle, the disp enser will be opened automatically. • When a program with hot prewa sh is selected (see program table), extra detergent must be placed in the cavity G/H (de ...
-
CDA WC460 - page 20
User instructions 19 • "3/1" Products If you wish to use detergents which already contain salt and rinse aid, check whether your dis hwasher is fitted with the " 3/1 option button " on the " Controls description " page and then ref er to the section which explains how to use this funct ion. If the button is not provi ...
-
CDA WC460 - page 21
User instructions 20 WARNING! • Make sure that the dishes are secu rely in place so that they cannot tip over or obstruct the rotati on of the spray arms during the washing cycle. • Do not place very small obj ects in the baskets as these could fall and obstruct the spray arms or the wash pump. • Containers such as cups, bowls, glasses and po ...
-
CDA WC460 - page 22
User instructions 21 4.4 Using the baskets The dishwasher has a capacit y of 10 place-settings , including servin g dishes. LOWER BASKET The lower basket receives the full force o f the lower spray arm, and should therefore be use d for the “t oughest” items with a heavier degree of soiling. All types and combinations of loads are permitted, pr ...
-
CDA WC460 - page 23
User instructions 22 CUTLERY BASKET The cutlery should be arrang ed in an orderly manner inside the basket, with the handles pointin g downwards. Take care during loading to av oid injury from the knife blades. T he basket is suitabl e for al l t ypes of cutler y, except those l ong enough to interfere w ith the upper spray arm. Ladles, wooden spoo ...
-
CDA WC460 - page 24
User instructions 23 LOADING THE UPPER BASKET Load plates facing for ward; cups, bowls etc. must always be faci ng downwards. The left-hand si de of the basket can be loaded with two layers of cups an d glasses. On the right plates and s aucers can be slotted verticalli into the forks. Loading examples: ADJUSTING THE UPPER BA SKET The upper basket ...
-
CDA WC460 - page 25
User instructions 24 5. Cleaning and maintenance Before carrying out any work, a lways unplug the appliance from the electrical supply or switch off the all- pole disconnec tion device. 5.1 General warnings and recommendations Avoid the use of acidic or abrasi ve detergents. Clean the outer surfaces and door-linin g of the dishwasher regularly usin ...
-
CDA WC460 - page 26
User instructions 25 CLEANING THE SPRAY ARM, TRAVELLING VERSION To remove the TRAVELLING spray arm, take hold of it and raise it t o release both the spray arm and the pipe from the tank, then detach the spray arm from the pip e. Wash both the pipe and the spra y arm in running water, re-attach the spra y arm to the pipe and return the assembly to ...
-
CDA WC460 - page 27
User instructions 26 GENERAL WARN INGS AND RECOMMEN DATIONS FOR CORRECT MAINTENANCE: • The fil ters should be cleaned under running water using a stiff brus h. • When removing the filter , take ca re that there are no food re sidues on it. If any residue s fall into the washing pit they might blo ck hydraulic components, or foul the sp ray arm ...
-
CDA WC460 - page 28
User instructions 27 If the dishes are not being cleaned p ro perly, check that: • the correct amount of det ergent has been ad ded; • there is regenerating salt in side the special c ontainer; • the dishes are being load ed c orrectly; • the selected program is suitable for the dish types and thei r degree of soiling; • all the filters a ...
-
CDA WC460 - page 29
User instructions 28 6. T roubleshooting The dishwasher is capa ble of signalling a number of faults through the simultaneous illumination of several indicator lights, with the follo w ing meanings: FAULT DESCRIPTI ON E1 Acquastop failure The anti-flooding system has been activated (for the relevant models only). The system is tripped in case of wa ...
-
CDA WC460 - page 30
User instructions 29 FAULT DESCRIPTI ON E7 Turbine flow-regulator malfunction (for the relevant models only) The appliance i s not able to "measure" the a mount of water loaded accurately. Interrupt the program and switch off the dish washer. Switch the dishwasher back on, program it again and start the washing cycle. If the probl em pers ...
-
CDA WC460 - page 31
User instructions 30 TECHNICA L DATA Width 447 ÷ 449 mm Depth measured flush with the outer edge of the control panel 550 mm Height from 820 mm to 890 mm Capacity 10 Standard place settings Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) Electrical characteristics See rating plate ...
-
CDA WC460 - page 32
19 570 0079 00 SX DX 3/4” min.10mm 3/4” 1/2” SW 32 MIN 40cm Cu ø10 Zet hem op één lijn met de bovenste rand van het durpaneel. Alinear respecto del borde superior del panel puerta. Alinhe com a borda superior do painel da porta. Allineare al bordo superiore del pannello porta. Align with the top edge of the door panel. Aligner au bord sup? ...
Haben Sie eine Frage bezüglich CDA WC460?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit CDA WC460 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit CDA WC460 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.