Bedienungsanleitung Pelco VS5008

20 Seiten 0.61 mb
Download

Zur Seite of 20

Summary
  • Pelco VS5008 - page 1

    ® VS5004/VS5008 Sequential Switcher INSTALLATION/OPERATION C808M-G (4/05) ...

  • Pelco VS5008 - page 2

    2 C808M-G (4/05) Contents Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco VS5008 - page 3

    C808M-G (4/05) 3 Description The VS5004 and VS5008 sequential switchers are designed to switch up to four (VS5004) or eight (VS5008) cameras manually or automatically to one or two monitors with automatic response to alarm inputs. Both versions are Coaxitron ® compatible and can be placed on a desktop or rack mounted. MODELS VS5004 Sequential swit ...

  • Pelco VS5008 - page 4

    4 C808M-G (4/05) Installation T ERMINATED CAMERA INPUTS AND ONE MONITOR OUTPUT 1. Make all equipment connections. Refer to Figure 1 (VS5004) or Figure 2 (VS5008). VS5008 only: When configured for one-monitor operation, the monitor must be connected to the MON 2 output. The MON 1 output must be terminated with a 75-ohm BNC terminator . 2. Make alar ...

  • Pelco VS5008 - page 5

    C808M-G (4/05) 5 Figure 2. VS5008 T erminated Camera Inputs - One Monitor Figure 3. VS5004 Alarm Connections VS5008 (REAR) MON 1 MON 2 MON X CAMERAS 87654321 12 V AC INPUT ALARM INPUT COM ALARM OUT 12345678 NOTE: MON 1 MUST BE TERMINA TED. MON 1 MON 2 1 2 3 4 1 2 3 4 ALARM 12V AC INPUT IN 1 2 3 4 COMMON 5 1 2 3 4 5 6 BRN RD OR YEL GRN BLK 6-PIN CON ...

  • Pelco VS5008 - page 6

    6 C808M-G (4/05) Figure 4. VS5008 Alarm Connections 12 V AC INPUT ALARM INPUT COM ALARM OUT 12345678 MON 1 MON 2 MON X CAMERAS 87654321 UP TO EIGHT ALARM INPUTS (ALARM INPUT FROM MOTION DETECTOR, DOOR CONT ACT , ETC., THROUGH NORMALL Y OPEN SWITCH). EACH ALARM DEVICE MUST BE CONNECTED TO THE "COM" TERMINAL. OPEN COLLECTOR OUTPUT FOR VCR A ...

  • Pelco VS5008 - page 7

    C808M-G (4/05) 7 LOOPING CAMERA INPUTS AND ONE MONITOR OUTPUT 1. Convert the switcher to looping operation. Refer to Figure 5 and do the following: NOTE: Looping and terminated inputs may be mixed. a. Remove the cover . b. Remove the rear panel of the chassis. c. Locate the 75-ohm resistors located on the inside of the rear panel BNC jacks. d. For ...

  • Pelco VS5008 - page 8

    8 C808M-G (4/05) Figure 5. Looping Conversion Modification Figure 6. VS5004 Looping Camera Inputs - One Monitor 75-OHM RESISTOR REAR PANEL (SWITCHER) BNC CONNECTOR CLIP HERE FOR EACH CHANNEL MON 1 MON 2 43 2 1 ALARM 12 V AC INPUT IN 1 2 3 4 OUT 6 COMMON 5 BRIGHT CONTRAST MON 1 VIDEO INPUTS ADDITIONAL EQUIPMENT TERMINA TED ...

  • Pelco VS5008 - page 9

    C808M-G (4/05) 9 Figure 7. VS5008 Looping Camera Inputs - One Monitor T ERMINATED CAMERA INPUTS AND T WO MONITOR OUTPUTS 1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following: a. Remove the cover . b. Remove the rear panel of the chassis. c. Remove the four screws attaching the PC board to the chassis. d. Pull the ...

  • Pelco VS5008 - page 10

    10 C808M-G (4/05) 4. Set the ALARM switch to the ON position. NOTES: • With all channel switches set to the AUTO position, both monitors immediately switch to the alarmed channel and the associated LED blinks. Multiple alarmed channels sequence every five seconds (VS5004) or three seconds (VS5008). The alarm has priority over the MONITOR/AUTO/BY ...

  • Pelco VS5008 - page 11

    C808M-G (4/05) 11 Figure 9. VS5004 T erminated Camera Inputs - T wo Monitors Figure 10. VS5008 T erminated Camera Inputs - T wo Monitors MON 2 MON 1 MON 2 43 2 1 ALARM 12 V AC INPUT IN 1 2 3 4 OUT 6 COMMON 5 BRIGHT CONTRAST BRIGHT CONTRAST MON 1 NOTE: IN THIS CONFIGURA TION, MON 1 MUST BE TERMINA TED WITH A 75-OHM TERMINA TOR AND MON 2 MUST BE IN T ...

  • Pelco VS5008 - page 12

    12 C808M-G (4/05) LOOPING CAMERA INPUTS AND T WO MONITOR OUTPUTS 1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following: a. Remove the cover . b. Remove the rear panel of the chassis. c. Remove the four screws attaching the PC board to the chassis. d. Pull the PC board and rear panel assembly out of the chassis. e. ...

  • Pelco VS5008 - page 13

    C808M-G (4/05) 13 7. Connect the AC adapter to the 12 V AC input plug on the rear of the VS5004 or VS5008. Connect the transformer to a 120 V AC (VS5004 or VS5008) or 230 V AC (VS5004/220 or VS5008/220) power source. After power up, the switcher will begin sequencing. 8. Using a screwdriver , adjust the DWELL interval control to the desired setting ...

  • Pelco VS5008 - page 14

    14 C808M-G (4/05) COAXITRON CONTROL To convert for use with a Coaxitron transmitter , do the following: 1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following: a. Remove the cover . b. Remove the rear panel of the chassis. c. Remove the four screws attaching the PC board to the chassis. d. Pull the PC board and rear ...

  • Pelco VS5008 - page 15

    C808M-G (4/05) 15 6. For channels with cameras connected to the video inputs, set the front panel switches to the AUTO position. All unconnected video inputs should have their channel switch set to the BYP ASS position. NOTES: • VS5004 and VS5008 with one-monitor configuration: All channels with a switch set in the AUTO position will automatical ...

  • Pelco VS5008 - page 16

    16 C808M-G (4/05) Figure 13. VS5004 with Coaxitron Control Figure 14. VS5008 with Coaxitron Control COAXITRON® RECEIVER MON 1 MON 1 MON 2 43 2 1 ALARM 12 V AC INPUT IN 1 2 3 4 OUT 6 COMMON 5 LOOPING OUTPUT INPUT FROM RECEIVER OUTPUT FROM MONITOR J6 J7 J8 BRIGHT CONTRAST VS5004 (REAR) COAXITRON® TRANSMITTER (REAR) TO FIXED CAMERAS OR ADDITIONAL RE ...

  • Pelco VS5008 - page 17

    C808M-G (4/05) 17 Specifications VIDEO Inputs T erminating (75 ohms) or looping Outputs Monitor 1 75 ohms Monitor 2 VS5004 Hi Z VS5008 75 ohms Monitor X VS5008 Coaxitron transmitter (nonamplified) output Gain Unity Dwell Adjustable from 1-70 seconds nominal Frequency Response Flat within +/-1 dB to 10 MHz Maximum Signal Level 2 Vp-p T ilt Less th ...

  • Pelco VS5008 - page 18

    18 C808M-G (4/05) ...

  • Pelco VS5008 - page 19

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series ...

  • Pelco VS5008 - page 20

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Produzent Pelco Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts Pelco VS5008 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pelco
- Bedienungsanleitungen VS5008
- Produktkarten Pelco
- Informationsbroschüren
- oder Energieetiketten Pelco VS5008
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pelco VS5008.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pelco VS5008, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pelco VS5008. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pelco VS5008 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pelco VS5008, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pelco VS5008 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pelco VS5008 verständlich ist.

Eine gänzliche Bedienungsanleitung von Pelco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pelco VS5008 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pelco VS5008 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pelco VS5008, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pelco VS5008 - die uns die ersten Schritte während der Nutzung von Pelco VS5008 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pelco VS5008 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pelco VS5008 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pelco VS5008?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco VS5008 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco VS5008 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)