Bedienungsanleitung Pelco Spectra IV

16 Seiten 0.93 mb
Download

Zur Seite of 16

Summary
  • Pelco Spectra IV - page 1

    INSTALLATION Spectra ® IV Series Spectra ® IV SE Series C3417M-B (11/06) In-Ceiling Mount Back Box ...

  • Pelco Spectra IV - page 2

    2 C3417M-B (11/06) Installation 1 3 4 2 5 ...

  • Pelco Spectra IV - page 3

    C3417M-B (11/06) 3 1. Locate the center point of th e mounting location and inser t the compass tool. Draw a circle. 2. Cut the circle out of the ceiling. 3. Attach the conduit fitting, lock nut, and safety chain bracket. Install a safety ch ain/cable (not supplied) that will support up to 16 poun ds (7.3 kg). 4. Open the hinged door to the back b ...

  • Pelco Spectra IV - page 4

    4 C3417M-B (11/06) 6 7 VIDEO UTP+ UTP- RX- RX+ TX+ TX- PWR- PWR+ GND AUX2 GND GND NO NC COM 7 6 5 4 3 2 1 ALARMS AUX1 ...

  • Pelco Spectra IV - page 5

    C3417M-B (11/06) 5 6. Suspended Ceiling Only: Install the ceiling tile with th e back box. Attach a T -rail cl ip on each side of the ceiling tile. 7. Connect wiring to the circuit board inside the back box. Whe n finished, clos e the door to th e back box and tur n on the power . The gr een LED will lig ht. NOTES: • Aux 1: Maximum 2 A at low vol ...

  • Pelco Spectra IV - page 6

    6 C3417M-B (11/06) A 8 9 10 SWITCH 1 AND 2 ...

  • Pelco Spectra IV - page 7

    C3417M-B (11/06) 7 8. Configure DIP switche s SW1 and SW2 locate d on the top of the dome drive. For DIP switch settings, ref er to the labels locat ed on the top of the dome drive o r to the Switch Settings section. NOTE: When connecting mor e than one Spectra ® dome to a single cont roller , terminate th e unit farth est from th e controller . T ...

  • Pelco Spectra IV - page 8

    8 C3417M-B (11/06) T roubleshooting If your dome do es not power u p properly after installati on, use the following steps. 1. Check the fuse on the circuit board inside the ba ck box for continuity . Replace the fuse if needed . 2. Check the wi ring with a vo lt meter to en sure pr oper voltage is being received into the back box. If your dome pow ...

  • Pelco Spectra IV - page 9

    C3417M-B (11/06) 9 Switch Settings WAR N IN G : If you are using D-ty pe or P-type control, your system may no t operate if the baud rate and address switches are not set corre ctly . T he switches are set at the fact ory at the de faults for D- type control (2400 baud an d address 1). T able E. Switch Settings for SW2 Special Sy stems S w i t c h ...

  • Pelco Spectra IV - page 10

    10 C3417M-B (11/06) T able F . Switch Settings for SW1, P-T ype Control NOTE: For Coaxitron controls, SW1 is not us ed; set all switches OFF . For D-type con trol systems, refer to T a ble G. T able G. Switch Settings for SW1, D-T ype Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF . For P-type contr ol systems, refe r t ...

  • Pelco Spectra IV - page 11

    C3417M-B (11/06) 11 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 71 ON ON ON OFF OFF OFF ON O FF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON O FF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON ...

  • Pelco Spectra IV - page 12

    12 C3417M-B (11/06) SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF ...

  • Pelco Spectra IV - page 13

    C3417M-B (11/06) 13 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF O FF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON O ...

  • Pelco Spectra IV - page 14

    14 C3417M-B (11/06) Specifications The materials used in the manufacture of this document and its co mponents are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains electrical or electronic components that mu st be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of wast ...

  • Pelco Spectra IV - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRA NTY Pelco will r epair or repla ce, without charge, any merchandise p roved defectiv e in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are a s noted below: • Five ye ars on FR/F T/FS Series fiber optic pro ducts and TW3000 Seri es unshielded ...

  • Pelco Spectra IV - page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherl ands | United Ar ab Emirates | United Kingdom | Un ...

Produzent Pelco Kategorie Home Security System

Dokumente, die wir vom Produzenten des Geräts Pelco Spectra IV erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pelco
- Bedienungsanleitungen Spectra IV
- Produktkarten Pelco
- Informationsbroschüren
- oder Energieetiketten Pelco Spectra IV
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pelco Spectra IV.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pelco Spectra IV, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pelco Spectra IV. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pelco Spectra IV ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pelco Spectra IV, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pelco Spectra IV hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pelco Spectra IV verständlich ist.

Eine gänzliche Bedienungsanleitung von Pelco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pelco Spectra IV bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pelco Spectra IV befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pelco Spectra IV, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pelco Spectra IV - die uns die ersten Schritte während der Nutzung von Pelco Spectra IV erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pelco Spectra IV hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pelco Spectra IV im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pelco Spectra IV?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco Spectra IV nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco Spectra IV hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)