Deutsch dropdown-ico

Bedienungsanleitung Delta 20-330

24 Seiten 1.68 mb
Download

Zur Seite of 24

Summary
  • Delta 20-330 - page 1

    INSTRUCTION MANUAL 5" x 6" Horizontal Band Saw (Model 20-330) P ART NO. 902126 05-31-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta 20-330 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta 20-330 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 20-330 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Delta 20-330 - page 5

    5 ADDITIONAL SPECIFIC SAFETY RULES 1. DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operation of this tool. 3. FOLLOW ALL WIRING CODES and recommended electrical connections. 4. USE THE ...

  • Delta 20-330 - page 6

    6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta 20-330 - page 7

    7 NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRA TES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRA TIONS CONT AINED IN THE MANUAL ARE REPRESENT A TIVE ONL Y AND MA Y NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED TO ILLUSTRA TE TECHNIQUE ONL Y . FOREWORD FUNCTIONAL DESCRIPTION Delta Model 20-330 is a horizontal and vertica ...

  • Delta 20-330 - page 8

    8 FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. ASSEMBL Y CAR TON CONTENTS Fig. 1A Hardwar e 1. Saw unit 2. Legs 3. Shelf 4. Wheel assembly 5. Stock advance stop 6. Stand handle 7. V ertical table 8. Vise clamping handwheel ...

  • Delta 20-330 - page 9

    9 ASSEMBLING ST AND 1. Assemble the two legs (A) and (B) Fig. 2, to the band saw base using the six 5/16-18x1" hex head cap screws, thr ee of which are shown at (C) Fig. 2, twelve 5/16" flat washers and six 5/16-18" hex nuts. Align the holes in the band saw with the holes in the legs. Place a 5/16" flat washer onto a 5/16-18x1&q ...

  • Delta 20-330 - page 10

    10 ASSEMBLING ST AND HANDLE Insert ends of handle (A) Fig. 5, into the two holes (B) on the right leg and fasten in place using the two cotter pins supplied. Fig. 5 ASSEMBLING STOCK ADV ANCE STOP Assemble the stock advance stop assembly (A) to the hole on the front of the table and tighten the two set screws (B), as shown in Fig. 6. Fig. 6 ASSEMBLI ...

  • Delta 20-330 - page 11

    11 Fig. 13 AUTOMA TIC SHUT -OFF When the band saw is in the horizontal position, the saw should shut itself off automatically . After a completed cut has been made, and the saw is in the down or horizontal position, the shut-off bracket (B) Fig. 14 will contact the toggle switch (A) and push it to the down position, turning off the power . IMPORT A ...

  • Delta 20-330 - page 12

    12 ADJUSTING BLADE TRACKING 1. Place the saw arm in the vertical position and open the wheel cover (A) Fig. 17. 2. T ur n on the band saw . The blade is tracking properly when the back of the blade (B) Fig. 17, is just touching the edge of the wheel flange (C). The back of the blade should not be rubbing against the flange. 3. If an adjustment is n ...

  • Delta 20-330 - page 13

    13 ADJUSTING BLADE GUIDE BEARINGS DISCONNECT MACHINE FROM POWER SOURCE. 1. The blade guide bearings (A) and (B) Fig. 20 should be adjusted so they just touch the sides of the blade (C) after the blade is tracking properly and the blade support bearing has been adjusted. T o adjust, proceed as follows: 2. Remove the cover plate that is attached to t ...

  • Delta 20-330 - page 14

    14 ADJUSTING BLADE GUIDE BRACKETS DISCONNECT MACHINE FROM POWER SOURCE. The left and right blade guide brackets (A) and (B) Fig. 22, are adjustable by loosening the two lock knobs (C) and sliding the brackets to accommodate the width of the work piece. The guide brackets (A) and (B) should be set as close as possible to the workpiece, without inter ...

  • Delta 20-330 - page 15

    15 ADJUSTING STOCK STOP The stock stop is used when more than one piece is to be cut to the same length. Position the stop block (A) Fig. 26, the desired distance away fr om the blade. lt is good practice to have the work contact the stop at the bottom of the work, as shown. The stop may be repositioned in or out by loosening set scr ew (B) and mov ...

  • Delta 20-330 - page 16

    16 BLADE SELECTION 1. Y our band saw uses blades 1/2" wide, 64½" long and .020-.025 thick. Accessory blades with a pitch (number of teeth per . inch of the blade) of 10 and 14 are available fr om Delta. 2. Never use a blade so coarse that less than three consecutive teeth are engaged in the workpiece at one time. (T oo few teeth will cau ...

  • Delta 20-330 - page 17

    17 CHANGING BAND SAW FROM HORIZONT AL TO VERTICAL POSITION Y our saw can be changed to the vertical position for notching, slitting or contour work as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Move the cutting arm to the vertical position and lock in place with the arm positioning lever (C) Fig. 32. Stop screw (A) Fig. 32 should bear agains ...

  • Delta 20-330 - page 18

    18 TYPICAL OPERA TIONS FOR VER TICAL BAND SAW NOTE: THIS BAND SAW IS RECOMMENDED FOR USE IN CUTTING MET AL ONL Y . Before starting the machine, see that all adjustments ar e properly made and the guar ds are in place. T ur n the upper wheel by hand to make sure that everything is corr ect BEFORE turning on the power . Keep the top guide within 1/8& ...

  • Delta 20-330 - page 19

    19 In spite of how well a band saw is maintained, problems can occur . The following troubleshooting guide will help you solve the more common pr oblems: (continued on next page) T rouble: SAW WILL NOT ST ART . Probable Cause Remedy 1. Saw not plugged in. 1. Plug in saw . 2. Fuse blown or circuit breaker tripped. 2. Replace fuse or reset circuit br ...

  • Delta 20-330 - page 20

    20 T rouble: BLADE WILL NOT TRACK. Pr obable Cause Remedy 1. Blade too loose 1. Adjust tension 2. Upper wheel not properly adjusted. 2. Adjust upper wheel. 3. Improperly adjusted blade support bearing. 3. Adjust blade support bearing. T rouble: BLADE WILL NOT ST A Y ON WHEEL. Pr obable Cause Remedy 1. Blade not tensioned properly . 1. Adjust blade ...

  • Delta 20-330 - page 21

    21 BAND SA W BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. Y ou can obtain long use fr om a band saw blade if you use it properly . Use blades of proper thickness, width and temper for the various types of material and cuts. Any one of a number of conditions may cause a band saw blade to break. Blade b ...

  • Delta 20-330 - page 22

    22 MAINTENANCE LUBRICA TING THE VISE SCREW The vise lead screw should be lubricated using light machine oil as needed. The drive gears run in an oil bath gear box and it should not be necessary to change this oil more than once a year unless the oil becomes contaminated or a leak occurs due to improper r eplacement of the gear box cover . T o chang ...

  • Delta 20-330 - page 23

    23 23 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, wa ...

  • Delta 20-330 - page 24

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Produzent Delta Kategorie Saw

Dokumente, die wir vom Produzenten des Geräts Delta 20-330 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Delta
- Bedienungsanleitungen 20-330
- Produktkarten Delta
- Informationsbroschüren
- oder Energieetiketten Delta 20-330
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Delta 20-330.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Delta 20-330, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Delta 20-330. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Delta 20-330 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Delta 20-330, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Delta 20-330 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Delta 20-330 verständlich ist.

Eine gänzliche Bedienungsanleitung von Delta sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Delta 20-330 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Delta 20-330 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Delta 20-330, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Delta 20-330 - die uns die ersten Schritte während der Nutzung von Delta 20-330 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Delta 20-330 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Delta 20-330 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Delta 20-330?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Delta 20-330 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Delta 20-330 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)