Bedienungsanleitung Toro 200

8 Seiten 0.55 mb
Download

Zur Seite of 8

Summary
  • Toro 200 - page 1

    Specifications: • Controls up to 200 stations for the Stand-Alone model • Input power supply 100 V AC, 50/60Hz 120 V AC, 50/60Hz 240 V AC, 50/60Hz • TDC output voltage: 40 V AC max. • TDC output power: 98V A max. • Storage temperature: -30C–60C • Operating temperature: 0–60C • Cabinet T ype: Non-corrosive, lockable wall mount, ind ...

  • Toro 200 - page 2

    Earth Ground Installation IMPORT ANT! The TDC surge protection components cannot properly function unless an ef ficient pathway to earth ground is provided. The ground path must be as direct as possible, without sharp bends and must not exceed 30 Ohm resistance (when measured with an earth ground resistance device). All electrical components throug ...

  • Toro 200 - page 3

    Power Source Installation Step 1 – T urn off the power at the power source location and place the controller ’s power switch to OFF . Connect and route the appropriate size 3-conductor cable (10 AWG [2.5mm 2 ] maximum) from the power source to the controller cabinet. The provided power cable access hole can accommodate a 1" (25mm) conduit ...

  • Toro 200 - page 4

    Station Decoder Installation The station decoder module is available in 1-station, 2-station or 4-station configuration. The decoder modules are installed into the TDC output board terminals. The stand-alone TDC model can handle up to 100 stations per output board. These stations can be connected to the output board terminals in any configuration ( ...

  • Toro 200 - page 5

    Paths – 1 23 4 V alve Box Maximum communication wire length between the controller and the farthest decoder is 15,000ft (4500m). Recommended Cable for Controller-to-Decoder is the Paige ® P7350D, 14 A WG, Solid Copper , Jacketed 2-Conductor, Direct Burial cable. White Black White Black White Black White Black The maximum communication wire lengt ...

  • Toro 200 - page 6

    Grounding Communication Cable IMPORT ANT! Cable Splices: In order for the wire connections to comply with the 2005 edition of the National Electric Code® Article 300.5 (Underground Installations) and 1 10.14 (Electrical Connections), in wet or damp locations, the connector must be listed under specification “UL 486D” if installed in a valve bo ...

  • Toro 200 - page 7

    Master V alve / Pump Relay Installation TDC provide switch terminals to control a master valve or a pump relay if the system requires it. Step 1 – Place the controller ’s power switch to OFF . Step 2 – Connect the Positive/Hot wire of the power source that controls the master valve or the pump relay to the Master valve/Pump relay switch termi ...

  • Toro 200 - page 8

    Lithium Battery Replacement A 3.9V Lithium battery (P/N 363-2200) is installed in the timing mechanism to sustain the controller ’s clock time and date for approximately 10-years with no additional power applied. Step 1 – Place the controller ’s power switch to OFF . Step 2 – Remove the ribbon cable from the rear of the timing mechanism. St ...

Produzent Toro Kategorie Smoke Alarm

Dokumente, die wir vom Produzenten des Geräts Toro 200 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Toro
- Bedienungsanleitungen 200
- Produktkarten Toro
- Informationsbroschüren
- oder Energieetiketten Toro 200
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Toro 200.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Toro 200, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Toro 200. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Toro 200 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Toro 200, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Toro 200 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Toro 200 verständlich ist.

Eine gänzliche Bedienungsanleitung von Toro sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Toro 200 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Toro 200 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Toro 200, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Toro 200 - die uns die ersten Schritte während der Nutzung von Toro 200 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Toro 200 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Toro 200 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Toro 200?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Toro 200 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Toro 200 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)