Bedienungsanleitung GBC USP 13

17 Seiten 2.27 mb
Download

Zur Seite of 17

Summary
  • GBC USP 13 - page 1

    USP 13 UNIVERSAL SPEED PUNCH Operator Manual ...

  • GBC USP 13 - page 2

    USP 13 UNIVERSAL SPEED PUNCH Operator Manual T able of Contents Operating Instructions 1 Service and Maintenance Agreement 2 Selecting Knife Set Up 3 Installation of Punching Die 4 Set Up Instructions 5 Quick Reference Instructions 8 Maintenance Instructions 9 General Rules for Grinding Pins 10 Options and Accessories 11 ...

  • GBC USP 13 - page 3

    USP 13 Universal Speed Punch Operating Instructions The Universal Speed Punch from GBC Automated Finishing Division is specially designed to punch various weight paper sheets and cover stock. The machine has a variable speed control which can be adjusted from 70-110 cycles per minute. The thickness of individual layers being punched is adjustable, ...

  • GBC USP 13 - page 4

    Service And Equipment Maintenance Agreement By purchasing the USP 13 you have invested in a highly capable punching machine that will give you years of r eliable service. T o help protect this investment be certain to take advantage of the GBC Equipment Maintenance Agr eement (EMA). The EMA provides your USP 13 with pr oper ongoing maintenance and ...

  • GBC USP 13 - page 5

    3 SELECTING KNIFE SET -UP 1. T ur n power off. 2. Cycle the machine with the hand wheel until the claw reaches between 10 and 11 o’clock. (Figur e 2) 3. Cam #115 sets when the separating knife will go into the stack. Adjust the cam so that the tip of the knife is about 1/8” (.13) from the trailing edge of the claw . (Figure 2) 4. Cam #36 sets w ...

  • GBC USP 13 - page 6

    USP 13 Installation of Punching Dies Using Quick Release Die Clamp Assembly When installing a punching die, be sure that the lower die support is wiped clean of dirt and paper chips. The bottom of the die itself should be cleaned likewise. Wiping the top and bottom of the die with a thin coating of oil is advisable. Place the die into the machine a ...

  • GBC USP 13 - page 7

    5 USP 13 SET -UP INSTRUCTIONS: After the punching die is properly installed, position the back gauge rail (#108, Figure 7) slightly ahead of the punch die back gauge so that a piece of paper can slide freely into the thr oat of the die and not hit the back gauge of the punch die. Cam (#37) activates the rear jogger (#34) and the side jogger (#29). ...

  • GBC USP 13 - page 8

    111 170 83 127 1.0 Figure 10 Figure 12 CLA W THESE SURF ACES TO BE IN LINE 46 Place a sheet of paper against pusher (#111) in its home position (rear). Install the thr ee paper support straps (#127 & #83, Figure 10) 1” away fr om the edge of the paper . Straps must be on top of transfer belts. Cycle the machine by hand until the pusher has pu ...

  • GBC USP 13 - page 9

    7 Position front (#49) and r ear (#56 & #48) supply stack guides so that the posts clear the paper stack by about 1/16”. A stack of 2 to 3 inches is requir ed. Locate adjustable stack guide post (#59) so that the post is in line with the separating knife. (Figure 13). Install front guide rail (#55) so that ther e is about 1/8” to 1/4” cle ...

  • GBC USP 13 - page 10

    USP 13 Universal Speed Punch QUICK REFERENCE INSTRUCTIONS 1. DIE REPLACEMENT BLOCK UP DIE WITH STICK PROVIDED LOWER DIE CLAMP STICK REMOVE DIE CLAMPS - FRONT & REAR REMOVE BOTTOM BOL TS RELEASE CLAMP - RELAX PRESSURE WITH HAND WHEEL SLIDE DIE OUT REPLACE DIE WITH STICK IN PLACE REPLACE BOTTOM BOL TS LOOSEL Y A TT ACH CLAMPS TIGHTEN BOL TS REMOV ...

  • GBC USP 13 - page 11

    9 It is recommended that the machine be lubricated once every two weeks. Lubricate by putting a few drops of machine oil in the lubricating holes, which are marked with red paint. All gears in the main body of the machine run in pans, which are partially filled with a special gear lubricating grease. This gr ease should be replenished occasionally ...

  • GBC USP 13 - page 12

    10 GENERAL RULES FOR GRINDING PUNCHING PINS OF PUNCHING TOOLS IT IS ALSO NECESSAR Y TO SHARPEN THE FEMALE PORTION (BOTTOM PLA TE) OF THE PUNCHING TOOL. SURF ACE GRIND THE TOP OF THE BOTTOM PLA TE UNTIL THE EDGES OF THE HOLES ARE SHARP . THIS WILL REQUIRE APPROXIMA TEL Y .005” OF STOCK REMOV AL. NOTE: IF THE PINS ARE SHARPENED EVER Y 100 HOURS, TH ...

  • GBC USP 13 - page 13

    11 USP 13 OPTIONS & ACCESSORIES 1. Short Sheet Assembly 2. Front and Rear Cradle Bracket Assemblies 3. Long Small Roller Assembly 4. Stack Guider Adaptor 5. Auxiliary Pusher Optional assemblies that can be purchased separately include: 1. Small Roller Assembly 2. Small Sheet Jog Adaptor 3. T abbed Stock Jog Adaptor R.H. 0165036200 + L. H. 01650 ...

  • GBC USP 13 - page 14

    12 ...

  • GBC USP 13 - page 15

    13 016509000 LONG SMALL ROLLER ASSEMBL Y The Long Small Roller Assembly is used when the standard Large Roller Assembly does not allow enough reach to grab a lift of paper when it is fully jogged. ...

  • GBC USP 13 - page 16

    14 ...

  • GBC USP 13 - page 17

    General Binding Corporation Northbr ook, Il 60062-4195 http://www .GBC.com PN 0165999900 Rev B ...

Produzent GBC Kategorie Time Clock

Dokumente, die wir vom Produzenten des Geräts GBC USP 13 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen GBC
- Bedienungsanleitungen USP 13
- Produktkarten GBC
- Informationsbroschüren
- oder Energieetiketten GBC USP 13
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung GBC USP 13.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen GBC USP 13, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen GBC USP 13. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts GBC USP 13 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts GBC USP 13, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von GBC USP 13 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von GBC USP 13 verständlich ist.

Eine gänzliche Bedienungsanleitung von GBC sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von GBC USP 13 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von GBC USP 13 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich GBC USP 13, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts GBC USP 13 - die uns die ersten Schritte während der Nutzung von GBC USP 13 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit GBC USP 13 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von GBC USP 13 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich GBC USP 13?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit GBC USP 13 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit GBC USP 13 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)