Bedienungsanleitung Cisco Systems 3

18 Seiten 0.31 mb
Download

Zur Seite of 18

Summary
  • Cisco Systems 3 - page 1

    C HAPTER 3-1 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) 3 Initial Switch Router Configurations This chapter describes ho w to initially configure th e Layer 3 switch routers. • Starting Up the Layer 3 Switch Router • Using the Console and the Management Port s ? ...

  • Cisco Systems 3 - page 2

    3-2 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Using the Console and the Manag ement Ports Step 4 Po wer on the switch r outer . Step 5 Enter CLI configuratio n mode by answering no when you a re prompted to enter the ...

  • Cisco Systems 3 - page 3

    3-3 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Configuring the Ma nagement Port Xmodem or Ymodem protocols. The X modem and Ymodem protocols support di f ferent speeds of f ile transfers. The maximum f ile transfer spe ...

  • Cisco Systems 3 - page 4

    3-4 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Configuring the Mana gement Port Y ou can configure the ma nagement port from an IP c o nnected network. T o o bta in remote management access using T elnet, use the follo ...

  • Cisco Systems 3 - page 5

    3-5 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Configuring the Host Name Y ou can disp lay the configuratio n file when you are in pri vileged EXEC (enable) mode. • T o see the current operating conf iguration, ente ...

  • Cisco Systems 3 - page 6

    3-6 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Using the Boot Flash M emory SIMM Viewing the Contents of Boot Flash Memory Y ou can perform the fo llo wing tasks with the associat ed command s to vie w the conten ts of ...

  • Cisco Systems 3 - page 7

    3-7 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Using the Boot Flash M emory SIMM Backing Up a System Image to a TFTP Server T o cr eate a backup copy of your sy stem image, you can cop y system images from boo t flash ...

  • Cisco Systems 3 - page 8

    3-8 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Using the Boot Flash M emory SIMM Copying a System Image from a TFTP Se rver to a Boot Flash Memory SIMM Y ou can copy system i mage f iles from a TFTP serv er to the boot ...

  • Cisco Systems 3 - page 9

    3-9 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Using the Boot Flash M emory SIMM Router# dir bootflash: Directory of bootflash:/ 1 -rw- 3173128 <no date> cat2948g-in-mz.120-7.W5.14.45 2 -rw- 3173364 <no date&g ...

  • Cisco Systems 3 - page 10

    3-10 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Using the Boot Flash M emory SIMM The follo wing example demo nstrates h o w to f irst eras e and clean boot flash memory and then copy the ne w system image from the TFT ...

  • Cisco Systems 3 - page 11

    3-11 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Recovering a System Image Using Xmodem and Ymodem Recovering a System Image Using Xmodem and Ymodem If you do not ha v e access to a network serv er and need to download ...

  • Cisco Systems 3 - page 12

    3-12 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Recovering a System Image Us ing Xmodem and Ymodem T o cop y a Cisco IOS image from a computer or workstati on to a router using the X modem or Ymodem protocol, use t he ...

  • Cisco Systems 3 - page 13

    3-13 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Recovering a System Image Using Xmodem and Ymodem • T o transfer from a local computer , connect the router’ s co nsole port to a COM port (serial port) on the comput ...

  • Cisco Systems 3 - page 14

    3-14 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Updating the System Image Updating the System Image This section prov ides minimal instruct ions for updatin g the system image on your Layer 3 switch router . This proce ...

  • Cisco Systems 3 - page 15

    3-15 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Updating the System Image T o co py both th e kno wn good s ystem image and the ne w system image from a TFTP serv er to the f ile system on your switch router , initiate ...

  • Cisco Systems 3 - page 16

    3-16 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Updating the System Image Verifying checksum... OK (0x799F) 3173128 bytes copied in 177.668 secs (17927 bytes/sec) Router# dir bootflash: Directory of bootflash:/ 1 -rw- ...

  • Cisco Systems 3 - page 17

    3-17 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco IOS Release 12.0(7)W5(15d) Chapter 3 In itial Switch Router Configurations Updating the System Image T o reload the switch router with the ne w system image in boot flash memory , perform the foll o wing steps, begi nning in global conf iguratio ...

  • Cisco Systems 3 - page 18

    3-18 Catalyst 2948G-L3 and Catalyst 4908G-L3 Software Feature and Configuration Guide 78-10408-01, Cisco I OS Release 12.0(7)W5(15d) Chapter 3 Initial Switch Router Configurations Updating the System Image Router> show version Cisco Internetwork Operating System Software IOS (tm) L3 Switch/Router Software (CAT2948G-IN-M), Version 12.0(7)W5(14.46 ...

Produzent Cisco Systems Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts Cisco Systems 3 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco Systems
- Bedienungsanleitungen 3
- Produktkarten Cisco Systems
- Informationsbroschüren
- oder Energieetiketten Cisco Systems 3
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Systems 3.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Systems 3, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Systems 3. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Systems 3 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Systems 3, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Systems 3 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Systems 3 verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Systems 3 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Systems 3 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Systems 3, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Systems 3 - die uns die ersten Schritte während der Nutzung von Cisco Systems 3 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Systems 3 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Systems 3 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Systems 3?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Systems 3 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Systems 3 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)