Bedienungsanleitung KTM 50 SX

42 Seiten 5.1 mb
Download

Zur Seite of 42

Summary
  • KTM 50 SX - page 1

    KTM-Sportmotorcycle AG A–5230 Mattighofen www.ktm.com KTM Group Partner 4/2007 FOTO: MITTERBAUER 50 SX JUNIOR 50 SX OWNER’S MANUAL 2008 3211222en *3211222en* 3211222en ...

  • KTM 50 SX - page 2

    ENGLISH 1 INTRODUCTION » Please insert the serial numbers of the motorcycle below Chassis number Engine number Stamp of dealer All information contained is without obligation. KTM-Sportmotorcycle AG particularly reserves the right to modify any equipment, technical specifications, prices, colors, shapes, materials, services, service work, construc ...

  • KTM 50 SX - page 3

    ENGLISH 2 IMPORTANT INFORMATION » INTENDED PURPOSE KTM mini-sports motorcycles are designed and constructed to resist the usual wear and tear of normal use in competitions. The motorcycles comply with the regulations and categories currently in effect with the leading interna- tional motorcycle associations. OWNER’S MANUAL Please read this manua ...

  • KTM 50 SX - page 4

    ENGLISH 3 IMPORTANT INFORMATION » W ARRANTY The service work specified in the "Lubrication and Maintenance Schedule" must be performed by a KTM workshop and recorded in the service manual otherwise claims under the warranty shall become void. No claims can be filed under the warranty for damage or consequential damage caused by manipulat ...

  • KTM 50 SX - page 5

    ENGLISH 4 IMPORTANT INFORMATION FOR PARENTS ABOUT SAFE DRIVING » KTM mini motorcycles are off-road motorcycles designed for one person only. They are not allowed on public roads. The vehicle dimensions and components are designed for children from 4 to 10 years of age with a maximum weight of. 35 kg (78 lbs) and a maximum height of 130 cm (51 in). ...

  • KTM 50 SX - page 6

    ENGLISH 5 TABLE OF CONTENTS » Page IMPOR T ANT INFORMA TION FOR P ARENTS ABOUT SAFE DRIVING . . . . . . . . . . . . . . . . . . . . . . . . .4 SERIAL NUMBER LOCA TIONS . . . . . . . . . . . . . . . . . . . .6 Chassis number . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Engine number . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • KTM 50 SX - page 7

    ENGLISH 6 SERIAL NUMBER LOCATIONS » Chassis number The chassis number is located on the type plate on the steering head. Enter this number in the field on page no 1. Engine number The engine number is stamped into the right half of the engine case next to the kickstarter . Enter this number in the relevant field on page 1. ...

  • KTM 50 SX - page 8

    ENGLISH 7 OPERATION INSTRUMENTS » Throttle grip The throttle grip is located on the right side of the handlebars. It is used to reduce the engine speed and, thus, the driving speed. Hand brake lever The hand brake lever is located on the right side of the handlebars and actuates the front wheel brake. The basic position can be adjusted to fit your ...

  • KTM 50 SX - page 9

    ENGLISH 8 OPERATION INSTRUMENTS » Choke Dell’Orto carburetor PHVA 14 DS (50SX Junior) Choke lever [1] is mounted to the right side of the carburetor . If you move the choke lever up to the stop, a hole is opened in the carburetor through which the engine can draw in additional fuel. This results in a "rich" fuel-air mixture required fo ...

  • KTM 50 SX - page 10

    ENGLISH 9 OPERATION INSTRUMENTS » Plugin - Stand (50 SX) A socket is provided on the left side of the frame for the plug-in stand [1] included in the scope of supply . Rebound damping function of the shock absorber By using the adjusting screw [2] , the degree of damping of the rebound can be adjusted. T urn the knob clockwise to increase damping, ...

  • KTM 50 SX - page 11

    ENGLISH 10 GENERAL TIPS AND WARNINGS FOR STARTING THE MOTORCYCLE » Running in – Even very precisely machined sections of engine components have rougher surfaces than components which have been slid- ing across one another for quite some time. Therefore, every engine needs to be broken in. Do not load the engine to the power limit during the firs ...

  • KTM 50 SX - page 12

    ENGLISH 11 DRIVING INSTRUCTIONS » What you should check before each start When you start off, the motorcycle must be in a perfect technical condition. For safety reasons, you should make it a habit to perform an overall check of your motorcycle before each start. The following checks should be performed: 1 CHECK TRANSMISSION OIL LEVEL A lack of ge ...

  • KTM 50 SX - page 13

    ENGLISH 12 DRIVING INSTRUCTIONS » Starting when the engine is cold 1 Open fuel tap [1] . 2 Operate the choke [2] . 3 Kick the side up all the way or remove the plug-in stand. 4 Apply the front brake. 5 Operate the kickstarter , depressing it all the way , without opening the throt- tle. – When starting the engine, put on motorcycle boots in orde ...

  • KTM 50 SX - page 14

    ENGLISH 13 DRIVING INSTRUCTIONS » Driving The engine speed, and thus the driving speed, are regulated by the throttle grip. The choke must always be deactivated as soon as the engine has warmed up. – After falling with the motorcycle, check all its functions thor- oughly before using it again. – A bent handlebar must always be replaced. Never ...

  • KTM 50 SX - page 15

    ENGLISH 14 PERIODIC MAINTENANCE SCHEDULE » 50 SX JUNIOR 50 SX A CLEAN MOTORCYCLE CAN BE CHECKED MORE QUICKLY WHICH SAVES MONEY! Service every 5 hours Service every 20 hours before every race ENGINE Check engine for leaks z z Change transmission oil z z Check spark plug, change it if necessary , set electrode gap z Check the clutch engagement speed ...

  • KTM 50 SX - page 16

    ENGLISH 15 PERIODIC MAINTENANCE SCHEDULE » NOTE: If the inspection establishes that permissible tolerances are exceeded, the respective components must be replaced. The kilometer reading for inspection intervals should not exceed 5 hours. Maintenance work performed by your authorized KTM workshop is not a substitute for care and maintenance by the ...

  • KTM 50 SX - page 17

    ENGLISH 16 MAINTENANCE WORK ON CHASSIS AND ENGINE » Removing the seat The quick-release mechanism [1] allows removal of the seat without tools. T urn the quick-release device approximately 180° counterclockwise, lift the rear portion of the seat and pull the seat off backwards. When mounting the seat ensure that the hook engages at the tank. Chec ...

  • KTM 50 SX - page 18

    ENGLISH 17 MAINTENANCE WORK ON CHASSIS AND ENGINE » Checking and adjusting the steering head bearing (50 SX) * The steering head bearing should be checked regularly for play . T o check, support the motorcycle frame and lift the front wheel off the ground. Now try to move the fork back and forth – you should not feel any play . T o adjust, loose ...

  • KTM 50 SX - page 19

    ENGLISH 18 MAINTENANCE WORK ON CHASSIS AND ENGINE » Basic suspension setup for the weight of the driver T o achieve maximum handling performance and to prevent the telescopic fork and shock absorber from being damaged, the basic setup of the suspension components must be suitable for your child's weight. At delivery , KTM's mini motorcyc ...

  • KTM 50 SX - page 20

    ENGLISH 19 MAINTENANCE WORK ON CHASSIS AND ENGINE » Telescopic fork maintenance * The telescopic fork must be serviced at least once a year . T o service the fork, proceed as follows: Prop up the motorcycle under the frame to take the load off the front wheel. Disassemble the front wheel, remove screw [1] from the brake caliper and unscrew holding ...

  • KTM 50 SX - page 21

    ENGLISH 20 MAINTENANCE WORK ON CHASSIS AND ENGINE » Cleaning the dust scrabbers of the telescopic fork The dust-protection bellows [1] are to remove dust and coarse dirt particles from the fork tube. However , after some time, dirt may also get in behind the dust-protection bellows. If this dirt is not removed, the oil sealing rings located behind ...

  • KTM 50 SX - page 22

    ENGLISH 21 MAINTENANCE WORK ON CHASSIS AND ENGINE » General information about KTM disc brakes BRAKE FLUID RESERVOIRS: The brake fluid reservoirs for the front brake is designed such that it does not need to be refilled, even if the brake shoes are worn. If the brake fluid level drops below the minimum level either the brake system has a leak or th ...

  • KTM 50 SX - page 23

    ENGLISH 22 MAINTENANCE WORK ON CHASSIS AND ENGINE » Checking the brake fluid level / refilling * The brake fluid reservoir is combined with the hand brake cylinder on the handlebar . T o check the brake fluid level, press the brake pistons back into the basic position. Move the hand brake cylinder in a horizontal position, remove the screws [1] an ...

  • KTM 50 SX - page 24

    ENGLISH 23 MAINTENANCE WORK ON CHASSIS AND ENGINE » Changing the basic position of the foot brake lever (50 SX Junior) The basic position of the foot brake lever can be changed by unscrewing screw [1] and then turning the retainer [2] . Afterwards, check the setting of the rear wheel brake. Adjusting the control cable on the rear wheel (50 SX Juni ...

  • KTM 50 SX - page 25

    Slide new brake shoes into the brake caliper a fasten with the screw [5] . T ighten the screw to 10 Nm and mount the locking screw [4] . Mount the rear wheel and actuate the foot brake lever until you can feel the pressure point. – It is very important to keep the brake disk free from oil and fatty matters. Otherwise, the braking effect would be ...

  • KTM 50 SX - page 26

    MAINTENANCE WORK ON CHASSIS AND ENGINE » Removing and mounting the front wheel Jack the motorcycle up by the frame so that the front wheel is suspended above the ground. Undo the hexagon nut [1] and remove it together with the washer . Hold the front wheel and pull out the wheel spindle [2] . Carefully take the front wheel out of the fork. – Do ...

  • KTM 50 SX - page 27

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 26 Tires, air pressure T ire type, tire condition, and air pressure level affect the way your motorcycle rides, and they must therefore be checked whenever you are getting ready to go anywhere on your motorcycle. – T ire size can be found in the technical specifications. – T ire condition has to ...

  • KTM 50 SX - page 28

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 27 Checking coolant level The coolant should be 10 mm (0.4 in) above the radiator fins when the engine is cold (see illustr .). In the event of the coolant being drained, always fill and bleed the system. If possible, always check level of cooling liquid when engine is cold. If you have to open the ...

  • KTM 50 SX - page 29

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 28 Changing the seat height The saddle can easily be raised by 25 mm (1 in). This lets you adjust the height as your child grows. Figures A and B show the fork and shock absorber positions for a low seat position. The fork tubes extend approx. 17 mm (0.7 in) (H) above the upper fork stabilizer . The ...

  • KTM 50 SX - page 30

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 29 Checking the gear oil level T o check the gear oil level, first remove the plug [1] . With the motorcycle parked in an upright position, a small quantity of oil should flow out of the indicator opening [2] . If oil must be added, tilt the motorcycle and pour automatic gear oil (Motorex A TF Super ...

  • KTM 50 SX - page 31

    ENGLISH 30 Adjusting the centrifugal clutch * A correctly adjusted centrifugal clutch will provide maximum engine perform- ance and ease of driving and prevent the engine from overheating. Clutch wear can affect the clutch engagement speed. The clutch will slip for a longer period of time at higher clutch engagement speeds, generating more friction ...

  • KTM 50 SX - page 32

    ENGLISH 31 CORRECTING CLUTCH WEAR: Check the clutch shoes for wear . If the surface is only slightly worn you can remount them again. NOTE: The centrifugal clutch has an outer diameter of approx. 82.5 mm when new . T o correct slight wear to the surface, you can insert one of the pretensioning disks [11] from each clutch spring between the clutch h ...

  • KTM 50 SX - page 33

    TROUBLE SHOOTING » ENGLISH 32 If you let the specified maintenance work on your motorcycle be carried out, disturbances can hardly be expected. Should an error occur nevertheless, we advise you to use the trouble shooting chart in order to find the cause of error . W e would like to point out that many operations cannot be performed by oneself. In ...

  • KTM 50 SX - page 34

    TROUBLE SHOOTING » ENGLISH 33 TROUBLE CAUSE REMEDY Engine stalling or running with four stroke cycle Carburetor overflows if level adjust too high, float needle seating is dirty or enlarged Loose carburetor jets Clean carburetor , if necessary replace float needle and adjust level T ighten jets High rpm misfiring Incorrect heat range spark plug or ...

  • KTM 50 SX - page 35

    CLEANING » ENGLISH 34 STORAGE » If you want to put your motorcycle away for longer periods of time, please observe the following instructions: – Clean motorcycle thoroughly (see chapter: CLEANING) – Change engine oil (old engine oil contains aggressive contaminations). – Check antifreeze and amount of cooling liquid. – the engine warm up ...

  • KTM 50 SX - page 36

    TECHNICAL DATA – ENGINE » ENGLISH 35 ENGINE 50 SX JUNIOR 50 SX Design single cylinder 2-stroke engine, with reed valve inlet Displacement 49.0 cc Bore/Stroke 39.5 / 40 mm Fuel SUPER fuel, research octane no 95, mixed with 2-stroke oil Oil/gasoline ratio 1 : 60 when using high grade 2-stroke oil (Motorex 2T Cross Power) When in doubt, please cont ...

  • KTM 50 SX - page 37

    ENGLISH 36 TECHNICAL SPECIFICATIONS - CHASSIS » CHASSIS 50 SX JUNIOR 50 SX Frame single downtube, split-cradle Fork Marzocchi Ø = 32 mm Wheel travel front/rear 140/205 mm (5.5/8 in) 185/185 mm (7.3/7.3 in) Rear suspension Central shock absorber WP Front brake Disk brake Ø 160 mm (6.4 in) Rear brake Drum brake Ø 90 mm (3.5 in) Disk brake Ø 140 ...

  • KTM 50 SX - page 38

    ENGLISH 37 HEAD WORD INDEX » Page Adjusting the centrifugal clutch . . . . . . . . . . . . . . . . . .30 Adjusting the control cable on the rear wheel (50 SX Junior) .23 Adjusting the idle speed (Dell’Orto PHBG 19 BS) . . .28 Adjusting the idle speed (Dell’Orto PHV A 14 DS) . . .28 Adjusting the throttle cable . . . . . . . . . . . . . . . . . ...

  • KTM 50 SX - page 39

    ENGLISH 38 ...

  • KTM 50 SX - page 40

    ENGLISH 39 ...

  • KTM 50 SX - page 41

    ENGLISH 40 ...

  • KTM 50 SX - page 42

    KTM-Sportmotorcycle AG A–5230 Mattighofen www.ktm.com KTM Group Partner 4/2007 FOTO: MITTERBAUER 50 SX JUNIOR 50 SX OWNER’S MANUAL 2008 3211222en *3211222en* 3211222en ...

Produzent KTM Kategorie Motorcycle

Dokumente, die wir vom Produzenten des Geräts KTM 50 SX erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen KTM
- Bedienungsanleitungen 50 SX
- Produktkarten KTM
- Informationsbroschüren
- oder Energieetiketten KTM 50 SX
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung KTM 50 SX.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen KTM 50 SX, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen KTM 50 SX. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts KTM 50 SX ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts KTM 50 SX, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von KTM 50 SX hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von KTM 50 SX verständlich ist.

Eine gänzliche Bedienungsanleitung von KTM sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von KTM 50 SX bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von KTM 50 SX befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich KTM 50 SX, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts KTM 50 SX - die uns die ersten Schritte während der Nutzung von KTM 50 SX erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit KTM 50 SX hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von KTM 50 SX im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich KTM 50 SX?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit KTM 50 SX nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit KTM 50 SX hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)