Bedienungsanleitung Alpine ERA-G311

35 Seiten 0.27 mb
Download

Zur Seite of 35

Summary
  • Alpine ERA-G311 - page 1

    R ERA-G311 Sound Field Processor • OWNER'S MANUAL (page 2- page 35) Please read this manual to maximize your enjoyment of the outstanding performance and feature capabilities of the equipment, then retain the manual for future reference. L.P.S. BBE SUR EQ DISP 2 LISTENING POSITION SELECTOR 7 BAND EQUALIZER / SURROUND 14 BAND EQUALIZER FRONT ...

  • Alpine ERA-G311 - page 2

    2 English Precautions DO NOT DISASSEMBLE OR ALTER. Doing so may lead to accident, fire or electric shock. KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN. If swallowed, consult a physician immediately. USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock. HALT USE IMMEDIATELY IF A PROBLEM APPEAR ...

  • Alpine ERA-G311 - page 3

    3 English Contents Page 4 ....................................................................... Precautions Basic Operation 5 ................................................................... Power ON/OFF 5 ..................... Adjusting Volume/Balance/Fader/Subwoofer Equalizer/Surround Operation 6 ............................................. ...

  • Alpine ERA-G311 - page 4

    4 English Temperature Be sure the temperature inside the vehicle is between +60°C (+140°F) and –10°C (+14°F) before turning your unit on. Installation Location Make sure the ERA-G311 will not be exposed to: • Direct sun and heat • High humidity • Excessive dust • Excessive vibrations Replacing Fuses Replace the fuse with one with the ...

  • Alpine ERA-G311 - page 5

    5 English Basic Operation Power ON/OFF The unit is turned OFF/ON from the head unit's Power switch. Operating procedures for use with non-Ai-NET Head Units Adjusting Volume/Balance/ Fader/Subwoofer Make each adjustment on the Head Unit. For PHASE switching, press and hold the Audio Control button on the Head Unit at least 2 seconds. Note: Some ...

  • Alpine ERA-G311 - page 6

    6 English Equalizer/Surr ound Operation 1 7 Band 14 Band Front 7 Band Rear 7 Band 1 Band Quantity Switching Press and hold the EQ SEL button for at least 4 seconds to switch the equalizer band from 7 to 14 bands. Note: In the 14 band equalizer mode, the surround cannot be used. Dual Function Press and hold the EQ SEL button for at least 4 seconds i ...

  • Alpine ERA-G311 - page 7

    7 English Equalizer/Surr ound Operation 1 2 3 4 5 6 Frequency Level ↓ Frequency Level ↓ ↓ Frequency Level ↓ Frequency Level ↓ Frequency Level ↓ Frequency Level Equalizer Presets Six typical equalizer settings are preset at the factory for a variety of musical source material. Setting 1: FLAT Press the EQ (EQUALIZER) button to select the ...

  • Alpine ERA-G311 - page 8

    8 English Equalizer/Surr ound Operation 1 EQ FLAT Adjusting the Equalizer Settings You can modify the Equalizer settings to create a response curve more appealing to your personal taste. Press the EQ (EQUALIZER) button repeatedly to select the Equalizer setting preset which you wish to adjust. The EQ indicator blinks for 5 seconds. The example show ...

  • Alpine ERA-G311 - page 9

    9 English Equalizer/Surr ound Operation 1 BBE 1 BBE 2 BBE 3 BBE OFF Selecting BBE Mode The BBE (Barcus Berry Electronics) processor installed in this unit is designed to correct the phase distortion inherent in most loudspeaker designs. Ensuring the phase integrity of the signal driving the speakers improves the accurate reproduction of the sound. ...

  • Alpine ERA-G311 - page 10

    10 English Equalizer/Surr ound Operation 1 Creating a Custom BBE Curve Press the BBE button to select a BBE mode to be adjusted. The BBE indicator will blink for 5 seconds. While the BBE indicator is blinking, press the EQ Band up/down ( r / l ) buttons to select either the high or low frequency bands to be adjusted. Adjust for desired levels by pr ...

  • Alpine ERA-G311 - page 11

    11 English Equalizer/Surr ound Operation Choosing the Listening Posi- tion Selector (L.P.S.) This feature gives the user the ability to adjust the time delay of the 4 main speakers to provide the ideal sound stage for each listener in the car. The staging can be optimized for the front passenger, driver, front passenger and driver, or front and rea ...

  • Alpine ERA-G311 - page 12

    12 English Equalizer/Surr ound Operation Adjusting L.P.S. Press the L.P.S. button repeatedly to select the L.P.S. mode you want to adjust. The L.P.S. indicator will blink for 5 seconds. While the L.P.S. indicator is blinking, press the up/down ( < , > ) and left/right ( l , r ) buttons, to fine tune the time correction for the selected positi ...

  • Alpine ERA-G311 - page 13

    13 English Equalizer/Surr ound Operation DSP Surround Presets The ERA-G311 employs DSP (Digital Signal Processing) to duplicate mathematically various listening environments. Six typical surround settings are provided for a variety of musical source material as follows. Note: If 14-band equalizer is selected, the DSP Surround function can not be us ...

  • Alpine ERA-G311 - page 14

    14 English Equalizer/Surr ound Operation Adjusting the Surround Settings You can adjust the Surround settings for your preference. Press the SUR button repeatedly to select the desired surround mode (except NORMAL). The selected surround mode indicator blinks for 5 seconds. While the surround mode indicator is blinking, press the > or < butto ...

  • Alpine ERA-G311 - page 15

    15 English Equalizer/Surr ound Operation Memorizing the Equalizer Settings Press the EQ button to select the desired equalizer setting (factory preset or your own) you wish to store in memory. Press and hold any one of the Memory buttons for at least 2 seconds. The Preset indicators blink for 5 seconds showing the unit is ready for storing. Press t ...

  • Alpine ERA-G311 - page 16

    16 English Equalizer/Surr ound Operation 2 1 Switching Display Press the DISP button to switch the display. Select one of the display patterns you like. Press and hold the DISP button for more than 2 seconds. The display will toggle between normal or inverted mode. Normal mode Example Reverse mode DISP DISP ...

  • Alpine ERA-G311 - page 17

    17 English Equalizer/Surr ound Operation Pattern EQ Pattern Spectrum Analizer Pattern Peak Hold Pattern Peak Value Increasing Pattern "i" Character Pattern Block Pattern Mirror Pattern Spectrum Dual Stack Pattern Scan Display (Repeats endlessly for 5 seconds from Pattern 2 to Pattern 8.) Display 1 2 3 4 5 6 7 8 9 Description ...

  • Alpine ERA-G311 - page 18

    18 English Remote Contr ol Operation VISUAL SEL AUDIO SEL BAND PROG DEFEAT A.PROC MUTE SELECT AV CD/3D/6D PWR UP VOL DN REMOTE CONTROL UNIT RUE-4160 ENT RUE-4160 VOL PWR REMOTE CONTROL UNIT BAND PROG SOURCE A. PROC CD/3D/6D RUE - 4180 RUE-4180 If an Alpine, Ai-Net compatible head unit is connected to the ERA-G311, some or all of the EQs functions c ...

  • Alpine ERA-G311 - page 19

    19 English Remote Contr ol Operation Selecting the Factory Preset Surround Modes Note: If 14-band equalizer is selected, the DSP Surround function can not be used. Press the A.PROC button and select the surround mode. ★ : Some functions or displays are limited depending on the Head Unit used. Press the Up ( 8 ) or Down ( 9 ) button to select the ...

  • Alpine ERA-G311 - page 20

    20 English Remote Contr ol Operation Selecting the BBE Mode Press the A.PROC (Audio Processor) button to select the BBE mode. ★ : Some functions or displays are limited depending on the Head Unit used. Press the Up ( 8 ) or Down ( 9 ) button to select the desired BBE mode. 1 RUE-4180 A. PROC Head Unit EQ SUR BBE LPS T-CORR Private RUE-4160 A.PROC ...

  • Alpine ERA-G311 - page 21

    21 English Remote Contr ol Operation Recalling the Stored Equalizer Settings Press the A. PROC button and select the Private mode. ★ : Some functions or displays are limited depending on the Head Unit used. Press the Up ( 8 ) or Down ( 9 ) button to select the stored setting from PRESET 1 to PRESET 6. 1 RUE-4180 A. PROC RUE-4160 A.PROC Head Unit ...

  • Alpine ERA-G311 - page 22

    22 English Remote Contr ol Operation Choosing the Listening Position Selector (L.P.S.) Press the A.PROC button to select the L.P.S. mode. ★ : Some functions or displays are limited depending on the Head Unit used. Press the Up ( 8 ) or Down ( 9 ) button to select the desired listening position. 1 RUE-4180 A. PROC Head Unit EQ SUR BBE LPS T-CORR P ...

  • Alpine ERA-G311 - page 23

    23 English Remote Contr ol Operation Turning the Defeat Mode On or Off (RUE-4160/RUE-4162 only) Press the DEFEAT button to skip the BBE/ Surround circuit and get flat equalizer setting. The display DEFEAT is shown on the Head Unit side. To cancel the DEFEAT mode, press the DEFEAT button a second time. 1 DEFEAT 2 DEFEAT ...

  • Alpine ERA-G311 - page 24

    24 English Remote Contr ol Operation The remote control operations (RUE-4185/ RUE-4160/RUE-4162) described in the following sections are applicable to full Ai-NET compatible units only (TDA-7558, etc.). Notes: • The following display examples appear in the Alpine Ai-compatible head unit displays. • These displays will differ depending upon the ...

  • Alpine ERA-G311 - page 25

    25 English Remote Contr ol Operation 1 2 SR LEVEL ±0 ENT 3 SR LEVEL +3 ENT SR TIME –1 ENT Adjusting the Surround Settings Select the surround mode to be adjusted. Refer to page 19 "Selecting the Factory Preset Surround Modes". Press the ENT button to activate (for 5 seconds) the adjustment mode. During the adjustment mode, press the 8 ...

  • Alpine ERA-G311 - page 26

    26 English Remote Contr ol Operation Making the BBE by Yourself Select the BBE mode you desire to adjust referring to the Page 20 "Selecting the BBE mode". Press the ENT button, and the BBE band will be displayed for 5 seconds. While the BBE band is displayed, press the c or f button to display the band (L/H) to be adjusted. While the ban ...

  • Alpine ERA-G311 - page 27

    27 English Remote Contr ol Operation 1 Storing Custom Equalizer Settings Customize the equalizer settings as described on page 24 "Customizing the Equalizer Settings". Press and hold the ENT button at least 2 seconds. Press the 8 or 9 button to select the curve to be stored from PRESET 1 to PRESET 6. Press the ENT button to store the curv ...

  • Alpine ERA-G311 - page 28

    28 English Remote Contr ol Operation Adjusting L.P.S. Select the L.P.S. mode to be adjusted. Refer to page 22 "Choosing the Listening Position Selector (L.P.S.)". Press the ENT button to activate (for 5 seconds) the L.P.S. adjustment mode. Press the 8 , 9 , c or f button to adjust for the desired position. 1 ENT 3 ENT 2 LPS F RUE-4160 RUE ...

  • Alpine ERA-G311 - page 29

    29 English Remote Contr ol Operation Adjusting the Time Correction Time Correction: The distance between the listener and the speakers in a car vary widely due to the special conditions of the mobile environment. This difference in the distances from the speakers to the listener creates a shift in the sounds image and frequency characteristics. Thi ...

  • Alpine ERA-G311 - page 30

    30 English Remote Contr ol Operation Adjusting the Time Correc- tion (Continued) Press the ENT button to activate the time correction mode. The time correction value will be displayed for 5 seconds. Press the BAND/PROG button to select the channel to be adjusted. Press the 8 or 9 button to adjust the time correction value. To advance to the next ba ...

  • Alpine ERA-G311 - page 31

    31 English Remote Contr ol Operation Storing the Time Correction Adjust the time correction value referring to page 29 "Adjusting the Time Correction". Press and hold the ENT button at least 2 seconds. Press the 8 or 9 button to select the time correction value to be stored from PRESET 1 to PRESET 6. Press the ENT button to store the time ...

  • Alpine ERA-G311 - page 32

    32 English Remote Contr ol Operation Recalling the Stored Time Correction Press the A. PROC button to select the time correction mode. ★ : Some functions or displays are limited depending on the Head Unit used. Press the 8 or 9 button to select the stored time correction from PRESET 1 to PRESET 6. 1 Head Unit EQ SUR BBE LPS T-CORR Private TC 1 ME ...

  • Alpine ERA-G311 - page 33

    33 English Remote Contr ol Operation Selecting the Factory Preset Equalizer Settings Selecting the Factory Preset Surround Modes Selecting the BBE Mode Recalling the Stored Equalizer Settings Choosing the Listening Position Selector (L.P.S.) Turning the Defeat Mode On or Off 7 Band Mode 14 Band Mode Dual Mode Adjusting the Surround Settings Making ...

  • Alpine ERA-G311 - page 34

    34 English Remote Contr ol Operation If you encounter a problem, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. Symptom No function or display. Cause and Solution • ...

  • Alpine ERA-G311 - page 35

    35 English Remote Contr ol Operation English Specifications Number of Bands .......................................................................................................................... 14 Equalizer Center Frequency Range ..................................................... 50/80/140/200/315/500/800/ 1.2k/2k/3.2k/5k/8k/11k/16kHz Frequ ...

Produzent Alpine Kategorie Car Stereo System

Dokumente, die wir vom Produzenten des Geräts Alpine ERA-G311 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Alpine
- Bedienungsanleitungen ERA-G311
- Produktkarten Alpine
- Informationsbroschüren
- oder Energieetiketten Alpine ERA-G311
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Alpine ERA-G311.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Alpine ERA-G311, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Alpine ERA-G311. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Alpine ERA-G311 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Alpine ERA-G311, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Alpine ERA-G311 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Alpine ERA-G311 verständlich ist.

Eine gänzliche Bedienungsanleitung von Alpine sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Alpine ERA-G311 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Alpine ERA-G311 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Alpine ERA-G311, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Alpine ERA-G311 - die uns die ersten Schritte während der Nutzung von Alpine ERA-G311 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Alpine ERA-G311 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Alpine ERA-G311 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Alpine ERA-G311?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Alpine ERA-G311 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Alpine ERA-G311 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)