Deutsch dropdown-ico

Bedienungsanleitung Snapper MRP215517B

32 Seiten 1.63 mb
Download

Zur Seite of 32

Summary
  • Snapper MRP215517B - page 1

    Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK MOWERS SERIES 17 MODEL NUMBER EXPLANATION MR P 21 70 17 BV MODEL DESIGNATION ENGINE DESIGNATION SELF-PROPELLED SERIES DESIGNATION CUTTING WIDTH ENGINE HORSE POWER M – Model Designation P – Self Propelled Model 17 – Series Designation R – Recycling Model 21 – 21” Cut ...

  • Snapper MRP215517B - page 2

    2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these in ...

  • Snapper MRP215517B - page 3

    3 IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE (Continued From Previous Page) 3. DO NOT remove fuel cap or add fuel w ith the engine running. Allow the engine to cool before refueling. 4. DO NOT refuel the machine indoors. 5. DO NOT store the machine or fuel container inside w here there is an open flame, spark or pilot light such as on ...

  • Snapper MRP215517B - page 4

    4 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 2 - 3 TABLE OF CO NTENTS ...................................................................................................... 4 SECTION 1 - FAMI LIARIZATI ON...................................................................... ...

  • Snapper MRP215517B - page 5

    5 Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operators of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices. Read, Understand and Follow the “IMPORTANT SAFETY INSTRU ...

  • Snapper MRP215517B - page 6

    6 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened. 2.1.2. Check blade control and wheel drive control to insure they work freely. See Figure ...

  • Snapper MRP215517B - page 7

    7 ENGINE SPEED CONTROL MOVE TO CHOKE POSITION Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2. 2 .1 . EN GI N E & BLADE (Choke Models) 1. Move fuel shut off valve to the “ON” position. See Figure 2.5. NOTE: Stop the engine (and blade) by releasing the blade control. FIGURE 2.5 2. Move engine speed control to the “ Ch o k ...

  • Snapper MRP215517B - page 8

    8 Section 2 - OPERATING INSTRUCTIONS 2.4 HANDLE HEIGHT ADJUSTMENT The height of the mower handle can be adjusted as follows: 1. Loosen the lower nuts on each lower handle as shown in Figure 2.8. FIGURE 2.8 2. Move upper mower handle up or down until the desired position is achieved. 3. Tighten the lower nuts on each lower handle to maintain desired ...

  • Snapper MRP215517B - page 9

    9 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.6 RECYCLING OPERATION NOTE: Fo ...

  • Snapper MRP215517B - page 10

    10 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.9 INSTALLATION of GRASS CATCH ...

  • Snapper MRP215517B - page 11

    11 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.13 INSTALLATION of DISCHARGE ...

  • Snapper MRP215517B - page 12

    12 Section 3 – MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number. WARNING DO NOT attempt any maintenance, adjustments or serv ...

  • Snapper MRP215517B - page 13

    13 Section 3 – MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather glov es w hen handlin ...

  • Snapper MRP215517B - page 14

    14 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves w h ...

  • Snapper MRP215517B - page 15

    15 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4. Sharpen blade on a grindin ...

  • Snapper MRP215517B - page 16

    16 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3 DRIVEN AND DRIVE DISC SER ...

  • Snapper MRP215517B - page 17

    17 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3.3. DRIVEN DISC ADJUSTMENT ...

  • Snapper MRP215517B - page 18

    18 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3.4. Replacing Rubber Drive ...

  • Snapper MRP215517B - page 19

    19 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3.6. Replacement Of Bearing ...

  • Snapper MRP215517B - page 20

    20 DRIVE DISC SLOT IN END OF DRIVE DISC BOLT BUSHING BOLT RETAINER DECK BRACKET (PARTIA LLY SHOWN) LOCK WA SHER NUT Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and compone ...

  • Snapper MRP215517B - page 21

    21 Section 4 - REPAIR & ADJUSTMENTS 4.5. BATTERY SERVICE 4.5.1. NEW BATTERY PREPARATION 1. Remove battery from c arton. 2. Place battery in a well ventilated area on a level non-concrete surface. 3. Remove battery cell caps. Fill cells with electrolyte to proper level. Filling battery with electrolyte will bring the battery to 80% charged state ...

  • Snapper MRP215517B - page 22

    22 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty. 1. F ill fuel tank w ith fresh fuel. Using Recoil Starter 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for Instructions. 3. Spark plug wire disconnected. 3. Place spark plug w ire onto spark plug. 4. Honda Engines Only ? ...

  • Snapper MRP215517B - page 23

    23 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 6 X Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre-Cleaner Clean Sponge Element Engine Manual X** Air Cleaner Clean or Replace Engine Manual X** Spark Plug Replace Engine Manual X Engine Cooling Syste ...

  • Snapper MRP215517B - page 24

    24 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in materi ...

  • Snapper MRP215517B - page 25

    25 PRIMARY MAINTENANCE ...

  • Snapper MRP215517B - page 26

    26 PRIMARY MAINTENANCE ...

  • Snapper MRP215517B - page 27

    27 PRIMARY MAINTENANCE ...

  • Snapper MRP215517B - page 28

    28 PRIMARY MAINTENANCE ...

  • Snapper MRP215517B - page 29

    29 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number _____________________________________________________________ Serial Number _____________________________________________________________ Date of Pu rchase ______________________ ...

  • Snapper MRP215517B - page 30

    30 NOTES ...

  • Snapper MRP215517B - page 31

    31 NOTES ...

  • Snapper MRP215517B - page 32

    32 Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK BEHIND MOWERS SERIES 17 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings. Read, Unders ...

Produzent Snapper Kategorie Lawn Mower

Dokumente, die wir vom Produzenten des Geräts Snapper MRP215517B erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Snapper
- Bedienungsanleitungen MRP215517B
- Produktkarten Snapper
- Informationsbroschüren
- oder Energieetiketten Snapper MRP215517B
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Snapper MRP215517B.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Snapper MRP215517B, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Snapper MRP215517B. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Snapper MRP215517B ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Snapper MRP215517B, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Snapper MRP215517B hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Snapper MRP215517B verständlich ist.

Eine gänzliche Bedienungsanleitung von Snapper sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Snapper MRP215517B bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Snapper MRP215517B befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Snapper MRP215517B, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Snapper MRP215517B - die uns die ersten Schritte während der Nutzung von Snapper MRP215517B erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Snapper MRP215517B hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Snapper MRP215517B im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Snapper MRP215517B?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Snapper MRP215517B nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Snapper MRP215517B hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)