Bedienungsanleitung Zebra 2722

30 Seiten 2.91 mb
Download

Zur Seite of 30

Summary
  • Zebra 2722 - page 1

    User’s Manual No. 980344-001 Rev. A ©2001 Zebra Technologies Corporation 2722 2742 3742 Desktop Thermal Printer User’s Manual ...

  • Zebra 2722 - page 2

    COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation. This docu - ment and the information contained within is copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra Technol - ogies Corporation. While every effort has b ...

  • Zebra 2722 - page 3

    TABLE OF CONTENTS Installation and Operation Unpacking Your Printer . . . . . . . . . . . . . . . . . . . . 2 Getting To Know Your Printer . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attach Power . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attach Interface Cable . . . . . . . . . ...

  • Zebra 2722 - page 4

    General Cautions and Warnings This page describes general safety and maintenance warnings and cautions for the printer and are referenced throughout the manual. Warning - Shock Hazard The printer should never be operated in a location where it can get wet. Personal injury could result. Warning - Static Discharge The discharge of electrostatic energ ...

  • Zebra 2722 - page 5

    1 Installation and Operation This section provides information on the instal- lation and operation of the printer. The printer is a low cost, desktop thermal bar code printer. LP models are direct thermal. TLP modes are thermal transfer and direct thermal printers. This family of printers is specifically de- signed for printing labels, tags or cont ...

  • Zebra 2722 - page 6

    Unpacking Your Printer Installation and Operation 2 980344-001 Rev.A For W in B a r C o d e L a b e l P r in t e r s S o ftw a re a n d D o c u m e n ta tio n 105551 -006 © 2001 Zeb ra T echno log ie s Co rporation ...

  • Zebra 2722 - page 7

    Getting To Know Your Printer 980344-001 Rev.A 3 Installation and Operation ...

  • Zebra 2722 - page 8

    Installation The following steps will guide you through the installation of the printer, media and software. Step 1 - Attach Power SHOCK HAZARD WARNING See page iv Installation and Operation 4 980344-001 Rev.A O XXXXXXXXXXXXXX XXXXXXXX XXXXXXXXX Power OFF Check Power Module Voltage Plug Into Power Module ...

  • Zebra 2722 - page 9

    Step 2 - Attach Interface Cable 980344-001 Rev.A 5 Installation and Operation Parallel Interface Serial Interface ...

  • Zebra 2722 - page 10

    Step 3 - Load Media Installation and Operation 6 980344-001 Rev.A Open Cover Open Print Head Open Guides MO VIE MO VIE MO VIE ...

  • Zebra 2722 - page 11

    Before You Load Media in the Printer You must remove the outside length of media (that is, one, full revolution of labels and any liner). When you remove this part of the media, you remove the oils, dust, and adhesives that contaminate it. Tape or adhesive holds the loose end and the outside length of media becomes contaminated when handled or stor ...

  • Zebra 2722 - page 12

    Step 3 - Load Media (cont.) Installation and Operation 8 980344-001 Rev.A 2722 Install Roll Media OUT OUT OUT OUT OUT OUT OUT OUT 2742 / 3742 Install Roll MO VIE ...

  • Zebra 2722 - page 13

    Step 3 - Load Media (cont.) 980344-001 Rev.A 9 Installation and Operation Thread the Media MO VIE MO VIE Seat Media Roll ...

  • Zebra 2722 - page 14

    Step 3 - Load Media (cont.) Installation and Operation 10 980344-001 Rev.A Close Guides Close Guides 2742 / 3742 MO VIE ...

  • Zebra 2722 - page 15

    Step 3 - Load Media (cont.) 980344-001 Rev.A 11 Installation and Operation Close Cover MO VIE MO VIE Close Print Head ...

  • Zebra 2722 - page 16

    Step 3 - Load Media (cont.) If the indicator fails to light, refer to Appendix A - Trouble Shooting. Run the AutoSense routine. Installation and Operation 12 980344-001 Rev.A Press FEED Button O Power ON ...

  • Zebra 2722 - page 17

    Step 4 - AutoSense Step 5 - Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980344-001 Rev.A 13 Installation and Operation O O 2 UKQ1813 4.00 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.9K avl Gmem:000K,0241K avl E I8,0,001 rY S8 D12 R032,000 ZT UN q0450 Q0800,034 Option:D 11 ...

  • Zebra 2722 - page 18

    Using Fan-Fold Media Installation and Operation 14 980344-001 Rev.A Place Media In Rear Face Print Surface UP Insert & Load Media ...

  • Zebra 2722 - page 19

    Label Dispenser Printers with an optional label taken sensor can dispense a single peeled label. Remove the label to automatically print the next label. 980344-001 Rev.A 15 Installation and Operation Expose 15CM of Labels (2722 Shown) Peel Exposed Labels Cut End of Exposed Liner (2722 Shown) Pull Print Head Release Lever (2722 Shown) Insert Liner U ...

  • Zebra 2722 - page 20

    Label Dispense Option Installation and Operation 16 980344-001 Rev.A TLP2722 Insert Liner (2742 Shown) Pull Liner Through (2742 Shown) ...

  • Zebra 2722 - page 21

    Label Dispense Option 980344-001 Rev.A 17 Installation and Operation Close Print Head Close Cover T LP2722 Push to Open Label Taken Sensor Press FEED Button TL P2722 Remove Presented Label ...

  • Zebra 2722 - page 22

    Thermal Transfer Ribbon Loading This feature is supported on TLP model printers, only. Installation and Operation 18 980344-001 Rev.A Thermal Transfer Print Head Mechanism MO VIE Ribbon Path ...

  • Zebra 2722 - page 23

    Thermal Transfer Ribbon Loading Open Print Head 980344-001 Rev.A 19 Installation and Operation Load Ribbon Core Load Transfer Ribbon Start Ribbon Open Print Head (Rear View) Pull Ribbon Around Print Head Close ...

  • Zebra 2722 - page 24

    Installation and Operation 20 980344-001 Rev.A ...

  • Zebra 2722 - page 25

    Appendix A - Troubleshooting Problem Solution or Reason POWER indicator does not light GREEN when power switch is turned to ON (1) position. 1. Check power connections from A.C. outlet to power supply to printer. POWER indicator lights GREEN, but printer will not print. 1. Check interface cable connections from computer to printer. Printer appears ...

  • Zebra 2722 - page 26

    Printer Maintenance 22 980344-001 Rev.A Clean the Print Head Don’t Clean Rollers with Cleaning Pen MO VIE ...

  • Zebra 2722 - page 27

    Printer Configuration Settings The printer has flash (non-volatile) memory to store printer configuration settings. The settings are stored in flash memory and are set by programing, printer drivers or the AutoSense routine. The settings are shown on the Dump mode printout or can be reported back to the host via the serial port. The following are t ...

  • Zebra 2722 - page 28

    Serial Interface Communication Configuration The printer’s serial port is configured with the Y command for the printer. The printer supports interface data rates from 1200 to 38,400 baud. See the programmer's manual for details. The printer’s serial port default configuration is: 9600 baud 8 bit data 1 stop bit No parity RS-232 Serial Int ...

  • Zebra 2722 - page 29

    Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. PrintServer) 980344-001 Rev.A 25 PRINTER DB -25 Pin No. Centronics Pin No. F emale DB -25 to Male Centronics (Cable) HOST STROBE D ATA 0 D ATA 1 D ATA 2 D ATA 3 D A ...

  • Zebra 2722 - page 30

    26 980344-001 Rev.A ...

Produzent Zebra Kategorie Printer

Dokumente, die wir vom Produzenten des Geräts Zebra 2722 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Zebra
- Bedienungsanleitungen 2722
- Produktkarten Zebra
- Informationsbroschüren
- oder Energieetiketten Zebra 2722
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Zebra 2722.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Zebra 2722, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Zebra 2722. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Zebra 2722 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Zebra 2722, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Zebra 2722 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Zebra 2722 verständlich ist.

Eine gänzliche Bedienungsanleitung von Zebra sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Zebra 2722 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Zebra 2722 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Zebra 2722, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Zebra 2722 - die uns die ersten Schritte während der Nutzung von Zebra 2722 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Zebra 2722 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Zebra 2722 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Zebra 2722?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Zebra 2722 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Zebra 2722 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)