-
Studer AJ SERIES - page 1
SINE WAVE INVERTER SINUS-WECHSELRICHTER ONDULEUR SINUSOÏDAL AJ SERIES User’s and installer’s manual Betriebs-und Montageanleitung Manuel d’utilisation et de montage ...
-
Studer AJ SERIES - page 2
STUDER INNOTEC AJ AJ V2.1 2/24 English descr iption................................................................................................... 3 Introduction ............................................................................................................... 3 Warning .............................................................. ...
-
Studer AJ SERIES - page 3
STUDER INNOTEC AJ AJ V2.1 3/24 English description Introduction The sine wave inverters of the AJ series have been designed to meet industrial and domestic needs. They meet the highest requirements of comfort, safety and reliability. Any device designed for the public electrical network of 230 V 50 Hz can be connected to them (up to the nominal pow ...
-
Studer AJ SERIES - page 4
STUDER INNOTEC AJ AJ V2.1 4/24 Connection The connection of the inverter should be done with utmost care. First connect the consumer devices so as to prevent any further contact once the 230 V voltage is present. The technical data and connection’s description, is either under one side of the inverter or onto the cable connection side. Installati ...
-
Studer AJ SERIES - page 5
STUDER INNOTEC AJ AJ V2.1 5/24 losses and cause malfunction of the inverter. Once the inverter is connected to the batteries, a 230 V voltage is present in the outlet of the inverter. Use Control and indicators Control switch on/off There is a switch on the inverter to activate or deactivate it. Use this function to save the energy of the batteries ...
-
Studer AJ SERIES - page 6
STUDER INNOTEC AJ AJ V2.1 6/24 Safety The inverter is electronically protected. But protection against polarity inversions of the battery occurs with an internal fuse, except for AJ 2100-12 inverter, which has no fuse . The following table will show you the di fferent failures and their consequences. FAILURE CONSEQUENCE SOLUTION Low battery voltage ...
-
Studer AJ SERIES - page 7
STUDER INNOTEC AJ AJ V2.1 7/24 Maintenance The inverters of the AJ series do not need any special maintenance. The casing may be cleaned with a damp cloth (not wet). In the case of malfunction, the inverter should be sent back to the manufacturer for control in its original packing. Before sending the inverter, check the table above. The battery is ...
-
Studer AJ SERIES - page 8
STUDER INNOTEC AJ AJ V2.1 8/24 Technical data M ODEL AJ 275 AJ 350 AJ 400 AJ 500 AJ 600 AJ 700 Battery voltage (V) 12 24 48 12 24 48 Input voltage (V) 10.5 - 16 21 - 32 42 - 64 10.5 - 16 21 - 32 42 - 64 C ontinuous / 30’ power (VA) 200/275 300/350 300/400 400/ 500 500/600 500/700 S tand-by / ON @ no load (W) 0.3*/1.9 0. 3*/3.3 0.4*/5 0.3/3.8 0.4/ ...
-
Studer AJ SERIES - page 9
STUDER INNOTEC AJ AJ V2.1 9/24 Model with built-in solar charger (option – S) The AJ inverters of the AJXXXX-S series have a built-in solar charger. The built-in solar charge controller is of the shunt and floating type. It may only be used by solar generators . The maximal voltage of the solar modules is 23 V for 12 V applications and 46 V for 2 ...
-
Studer AJ SERIES - page 10
STUDER INNOTEC AJ AJ V2.1 10/24 Deutsche Beschreibung Einführung Die Wechselrichter der Serie AJ sind für den Betrieb von a llen handelsüblichen 230V Geräten konzipie rt worden. Die AJ genügen den höchst en Anforderungen an Zuverlässigkeit, Sicherheit und Komfort. Jedes für das 230V-Wechselstromnetz geeignete Gerät kann auch mit einem AJ b ...
-
Studer AJ SERIES - page 11
STUDER INNOTEC AJ AJ V2.1 11/24 Anschluss Der Anschluss des AJ muss mit beson- derer Vorsicht ausgeführt werden. Eine sichere und einwandfreie Funktion der Anlage wird dadurch gewährleistet. Die Gerätedaten und die Anschlussbezeich- nung befinden sich auf der Gehäuse- unterseite oder auf der Kabelanschlus- seite. Vor dem Anschluss des AJ an die ...
-
Studer AJ SERIES - page 12
STUDER INNOTEC AJ AJ V2.1 12/24 der AJ zur Kontrolle an den zuständigen Händler gebracht werden. Draht Schwarz: -Minus-Pol Draht Rot : + Plus-Pol Für die Kabel den AJ 275-350-400 gel- ten die jeweils dom inierenden Farben! Den AJ an die Batterie anschliessen. Beim Anschliessen der Batterie entsteht ein Funken (EXPLOSIONSGEFAHR!) wegen der Ladung ...
-
Studer AJ SERIES - page 13
STUDER INNOTEC AJ AJ V2.1 13/24 trolle diesen kleinen Verbraucher aus- schalten,-der Wechselrichter muss nach einigen Sekunden wieder im Stand-by- Modus arbeiten. Geschieht dies nicht, ist die Last des Verbrauchers zu klein um erkannt zu werden. Ist der Stand-by- Modus nicht er- wünscht, muss der Drehknopf ganz nach rechts gedreht werden. VORSICHT ...
-
Studer AJ SERIES - page 14
STUDER INNOTEC AJ AJ V2.1 14/24 Unterhalt Die Wechselrichter AJ benötigen keinen Unterhalt. Bei Bedarf kann das Gehäuse mit einem feuchten, nicht nassen Lap- pen gereinigt werden. Bei Funktionsstörungen des Wechsel- richters muss dieser sehr gut verpack t zur Kontrolle an den Händler zurückge- sandt werden. Dassel be gilt auch bei jeglicher ä ...
-
Studer AJ SERIES - page 15
STUDER INNOTEC AJ AJ V2.1 15/24 Die Firma STUDER INNOTEC behält sich das Recht vor, Änderungen der technischen Daten, des Produkts oder der Betriebsanweisung vorzunehmen. JT8 Fernsteuerung für AJ 1000-2400 Die Funktionen und Anzeigen der Fern steuerung sind dieselben wie die im Wechselrichter (si ehe Kapitel Anwendungen). Die Fernsteuerung wird ...
-
Studer AJ SERIES - page 16
STUDER INNOTEC AJ AJ V2.1 16/24 Solarladeregler für fotovoltaï- sche Solarmodule (Option – S) Der in den Wechselrichtern AJ mit der Option „S“ eingebaute Solarladeregler ist ausschliesslich nur für den Anschluss von fotovoltaïschen Solarmodulen ge- eignet um damit die Batterien zu laden ! Sämtliche anderen Strom- oder Span- nungsquellen ...
-
Studer AJ SERIES - page 17
STUDER INNOTEC AJ AJ V2.1 17/24 Instructions en français Introduction Les onduleurs de la série AJ ont été conçus de manière à répondre aux besoins tant industriels que domestiques. Ils satisfont aux plus hautes exigences de confort, de sécurité et de fiabilité. Chaque appareil conçu pour le réseau électrique 230 V 50 Hz peut s’y br ...
-
Studer AJ SERIES - page 18
STUDER INNOTEC AJ AJ V2.1 18/24 Raccordement Le raccordement doit être l’objet d’une attention toute particulière. De celui-ci dépend le bon fonctio nnement de toute l’installation. Les données techniques ou la description de raccordement se trouvent soit sur un des côtés inférieurs de l’appareil ou du côté de l’embranchement du ...
-
Studer AJ SERIES - page 19
STUDER INNOTEC AJ AJ V2.1 19/24 Cependant, si la polarité est inversée, l’onduleur doit être retourné en usine pour contrôle. Raccordez la batterie en utilisant les câbles aux couleurs suivantes : Câble NOIR : Pôle négatif (-) Câble ROUGE : Pôle positif (+). Pour AJ 275-350-400 appliquer la couleur dominante comme couleur de référenc ...
-
Studer AJ SERIES - page 20
STUDER INNOTEC AJ AJ V2.1 20/24 Si le stand-by n’est pas souhaité, tourner le bouton complètement à droite. La puissance minimale détectée peut être ajustée entre 1 et 20 W. Dans la plupart des installations, ce réglage n’est pas utile. Le réglage se fait à l’aide d’un tournevis plat n°1 dans l’ouverture notée stand-by sur l? ...
-
Studer AJ SERIES - page 21
STUDER INNOTEC AJ AJ V2.1 21/24 Maintenance Les onduleurs de la série AJ ne nécessitent aucun entretien particulier. Le boîtier peut être nettoyé avec un chiffon humide (pas mouillé). Si un dysfonctionnement ou une déformation mécanique de la boite ou des câbles devait apparaître, l’onduleur doit être envoyé, soigneusement emballé da ...
-
Studer AJ SERIES - page 22
STUDER INNOTEC AJ AJ V2.1 22/24 J T8 Commande à distance pour AJ 1000-2400 Les fonctions de la télécommande sont les mêmes que les fonctions disponibles sur l’onduleur. (Voir chapitre Utilisation) La télécommande doit être raccordée à l’onduleur à l’aide du câble d’origine STUDER (10m) ou tout au tre câble RJ11/6p 1:1 jusqu’à ...
-
Studer AJ SERIES - page 23
STUDER INNOTEC AJ AJ V2.1 23/24 Modèles avec chargeur solaire (option – S) Le régulateur de charge à disposition dans l’onduleur AJ est destiné exclusivement à la charge de la batterie par des modules photovoltaïques . Toute autre source de courant nécessite l’usage d’un régulateur de charge adapté à cette source. La tension à vi ...
-
Studer AJ SERIES - page 24
STUDER INNOTEC AJ AJ V2.1 24/24 DECLARATION OF CONFORMITY Manufacturer’s Name: Studer INNOTEC Manufacturer’s address: Rue des Casernes 57, CH - 1950 Sion Declares that the product: Sine wave inverter Product Name: AJ series Model Number: AJ 275-12, AJ 350-24, AJ 400-48 AJ 500-12, AJ 600-24, AJ 700-48 AJ 1000-12, AJ 1300-24 AJ 2100-12, AJ 2400-2 ...
Haben Sie eine Frage bezüglich Studer AJ SERIES?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Studer AJ SERIES nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Studer AJ SERIES hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.