Bedienungsanleitung Dynex DX-TVMLPTB03

18 Seiten 6.58 mb
Download

Zur Seite of 18

Summary
  • Dynex DX-TVMLPTB03 - page 1

    DX - T V M L P T B 0 3 Low- Prof il e T V Wall M ou nt Sa fet y in for m ati on a nd sp ec i fi cat io ns . . . 2 T ools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package contents . . . . . . . . . . . . . . . . . . . . . . 3 Installation in struc tions . . . . . . . . . . . . . . . . . 5 F or either wood-stu d or concrete wall ...

  • Dynex DX-TVMLPTB03 - page 2

    2 Safety infor mation and spec ifications IMPORT ANT SAFET Y INSTRUCTIONS - SA VE THESE INSTRUCTIONS CA UTI ON: Do not use this product for any purpose no t explicitly spe cified by Dy nex. Improper installa tion may cause proper ty damag e or personal injur y . If you do not understa nd these direc tions, or have doubts about the safety of the ins ...

  • Dynex DX-TVMLPTB03 - page 3

    DX-TVMLPTB03 3 T ools needed Y ou will need the following tools to assemble your new TV wall mount: ardware P ackage contents Make sure that y ou hav e all the hardwar e ne cessary to assem ble your new TV wall mount: A W all Plate (1) C Right T V Bracket (1) B Left T V Br ac ke t ( 1) HD M I C ab le Edge -to- edge stud fi nder Pen ci l Lev el Phil ...

  • Dynex DX-TVMLPTB03 - page 4

    4 T V Hardware Bag Label Har dware Qty . E4 F4 G 8 H4 I4 J4 K4 M4 × 12 m m screw M4 × 3 5 mm screw M4 wash er M6/M8 was her Univ ersal spa cers M6 × 12 m m scre w M6 × 20 m m screw Label Har dwa re Qty . L4 M4 N4 O4 P4 M6 × 35 mm screw M8 × 16 m m screw M8 × 35 m m screw Lag bolt washer 5/16" × 2 3/4" lag bolt 1 0 20 30 40 50 6 0 ...

  • Dynex DX-TVMLPTB03 - page 5

    DX-TVMLPTB03 5 Installa tion instructions STEP 1- Determine wh ether your T V ha s a flat bac k or an irregular or obstruc ted ba ck 1 Carefully plac e your TV screen face -d own on a cushioned, clean sur face to protect the screen from damages an d scratches. 2 If your T V has a table- top stand attac hed, remove the stan d. See the documentation ...

  • Dynex DX-TVMLPTB03 - page 6

    6 STEP 2 - Select screw s, w ashers , and spacer s 1 Select the hardware for your TV (screws, washers, and spacers). A limited numbe r of TVs come with mounting hardware included. (If there are screws that came with the T V , they are almost always in th e holes on the back of the T V .) If you don't know th e correct length of the mounting sc ...

  • Dynex DX-TVMLPTB03 - page 7

    DX-TVMLPTB03 7 STEP 3 - Opti on 1: Attach ing the m ounting ha rdware to T V s with a f lat back Note : I f you plan t o use a 5° tilt with a larg er T V (42”+), we suggest using spac ers with the mounting bra ckets so that the bottom of the TV does not touch the wall . 1 Align the left and right T V brackets ( B and C ) with the screw holes on ...

  • Dynex DX-TVMLPTB03 - page 8

    8 Special instructions f or VESA 100 x 100 and VESA 100 x 200 c onfigura tions These special instructions ap ply it you need to install the brackets on a sm all TV with the VESA 100 x 100 or VESA 100 x 200 configurations. Due to the way the T V mounting brackets ( B and C ) are made, the up per screw hole that must be used for this installation is ...

  • Dynex DX-TVMLPTB03 - page 9

    DX-TVMLPTB03 9 STEP 3 - Opti on 2: Attach ing the m ounting ha rdware to T V s with irregular or obstruc ted backs Note : I f you plan t o use a 5° tilt with a larg er T V (42”+), we suggest using spac ers with the mounting bra ckets so that the bottom of the TV does not touch the wall . 1 Align the left and right T V brackets ( B and C ) with t ...

  • Dynex DX-TVMLPTB03 - page 10

    10 STEP 4 - A djust the length of the str aps • For ease of access, the straps should be level with the bottom of the TV . DX-TVMLPTB03_14-0885 _MAN_V1_ENG.fm Page 10 Thursday, Aug ust 21, 2 014 8:10 AM ...

  • Dynex DX-TVMLPTB03 - page 11

    DX-TVMLPTB03 11 STEP 5 - Determine wall-mount location Notes: • For mor e detailed inf ormation on det ermining wher e to drill y our holes , visit our on line height-find er at: http://mf1.bestbuy .selectionassistant .c om/index.php/heigh tfinder • Y our T V should be hig h enough so your eyes a r e le vel with the middle of the scr e en. Norm ...

  • Dynex DX-TVMLPTB03 - page 12

    12 STEP 6 - Option 1: Installing on a wood stud wall Note : A ny dry wall c overing the wall must not exc eed 5/8" (16 mm). 1 Locat e the stud s. V erify the centers of the stu ds with an edge-to - edge stud finder . 2 Align the wall p late ( A ) at the he ig ht you de ter min ed i n t he pre vio us s tep, ma ke s ure t hat it is leve l, th en ...

  • Dynex DX-TVMLPTB03 - page 13

    DX-TVMLPTB03 13 Y ou’l l need 3 in. (75 mm) - Minimum woo d stud size: common 51 x 102 mm (2 x 4 in.) nominal 38 x 89 m m (11/2 x 31/2 in.). - Minimum spacing between horizontal fastene rs cannot be less than16 in. Edge-t o edge stud finder P (4) Pen ci l Drill 7/32" wood drill bit 1/2" soc ket wr enc h Level O (4) Wal l p la t e ( A ) ...

  • Dynex DX-TVMLPTB03 - page 14

    14 STEP 6 - Option 2: Installing on a so lid c oncrete or concret e block w all CAUTION: T o prevent pr opert y damage or personal injury , never drill into mortar between blocks. Mount the wall plate dir ectly onto the co ncre te surface . 1 Align the wall plate ( A ) at the hei ght you d ete rm ine d in th e p revi ou s ste p, make sure th at it ...

  • Dynex DX-TVMLPTB03 - page 15

    DX-TVMLPTB03 15 . Y ou ’ll need 3 in. (75 mm) * Mini mum solid concrete thick ness: 8 in. (203m m). * Minimu m concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm). The minimum d istance between the top two faste ners cannot be less than 16 i n. See Note* * Note : Not includ ed . Cal l Customer Ser vi ce to hav e the F ischer UX10 x 60 concr ...

  • Dynex DX-TVMLPTB03 - page 16

    16 STEP 7 - Mou ntin g the T V to the wal l plate 1 Place the TV brackets ( B and C ) i nto t he sl otte d f la ng es of t he wall p late ( A ). 2 Push the bottom of the T V toward the wall until the latch mechanism clic ks into place. 3 T o adjust t he tilt, loosen the wing nu t on each of th e brackets, tilt as necessar y , t hen tighten the w in ...

  • Dynex DX-TVMLPTB03 - page 17

    DX-TVMLPTB03 17 Removing the T V from the wall plat e 1 Grasp the T V by the bottom edge, then p ull down on the locking cords and pull the bottom of the T V out from the wall. 2 Release th e locking cords and lift the top of th e TV from the wall bracket. Pull down t o unlatch. HEA VY! Y ou wil l need a ssi stanc e with this step. DX-TVMLPTB03_14- ...

  • Dynex DX-TVMLPTB03 - page 18

    ww w.dynex prod ucts .com 1-800-305-2204 (U.S. and Canada) or 01-800-926-3020 (M exico) D YNEX is a trademark of Best Buy a nd its affiliated companie s. Registered i n some co untrie s. Distribute d by Best Buy Pur chasing, LL C 7601 Penn A ve. South, Richfield, MN 55423 U.S.A. © 2014 Best Bu y . All rights reserved. Made i n China . V1 ENGL ISH ...

Produzent Dynex Kategorie TV Mount

Dokumente, die wir vom Produzenten des Geräts Dynex DX-TVMLPTB03 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Dynex
- Bedienungsanleitungen DX-TVMLPTB03
- Produktkarten Dynex
- Informationsbroschüren
- oder Energieetiketten Dynex DX-TVMLPTB03
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Dynex DX-TVMLPTB03.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Dynex DX-TVMLPTB03, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Dynex DX-TVMLPTB03. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Dynex DX-TVMLPTB03 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Dynex DX-TVMLPTB03, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Dynex DX-TVMLPTB03 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Dynex DX-TVMLPTB03 verständlich ist.

Eine gänzliche Bedienungsanleitung von Dynex sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Dynex DX-TVMLPTB03 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Dynex DX-TVMLPTB03 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Dynex DX-TVMLPTB03, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Dynex DX-TVMLPTB03 - die uns die ersten Schritte während der Nutzung von Dynex DX-TVMLPTB03 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Dynex DX-TVMLPTB03 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Dynex DX-TVMLPTB03 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Dynex DX-TVMLPTB03?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Dynex DX-TVMLPTB03 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Dynex DX-TVMLPTB03 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)