Deutsch dropdown-ico

Bedienungsanleitung Pentax 1938507

286 Seiten 5.58 mb
Download

Zur Seite of 286

Summary
  • Pentax 1938507 - page 1

    Operating Manual • Specifications and external dimensions are subject to change without notice. 57988 Copyright © PENTAX Corporation 2008 00-200712 Printed in Philippines PENTAX Corporation 2-36-9, Maeno-cho, Itabashi-ku, Tokyo 174-8639, JAPAN (http://www.pentax.co.jp/) PENTAX Europe GmbH (European Headquarters) Julius-Vosseler-Strasse, 104, 225 ...

  • Pentax 1938507 - page 2

    Thank you for purchasing this PENTAX u Digital Camera. Please read this manual before using the camera in order to get the most out of all the features and functions. Keep this manual safe, as it can be a valuable tool in helping you to understand all the camera capabilities. Lenses you can use In general, lenses that can be used with this camera a ...

  • Pentax 1938507 - page 3

    1 We have paid close attention to the safety of this product. When using this product, we request your special attention regarding items marked with the following symbols. Warning • Do not disassemble or modify the camera. High voltage areas are present inside the camera, with the risk of electric shock. • If the camera interior is exposed due ...

  • Pentax 1938507 - page 4

    2 Caution • Do not short the battery or dispose of the battery in fire. Do not disassemble the battery. The battery could explode or catch fire. • Remove the battery from the camera immediately if they become hot or begin to smoke. Be careful not to burn yourself during removal. • Some portions of the camera heat up during use. There is the r ...

  • Pentax 1938507 - page 5

    3 • Only use the battery charger D-BC50 supplied with the camera. Do not use the product at a voltage other than the specified voltage. Use with a power source or voltage other than that designed can cause a fire or electrical shock. The specified voltage is 100 - 240V AC. • Do not use the battery charger to charge batteries other than recharge ...

  • Pentax 1938507 - page 6

    4 • Do not clean the product with organic solvents such as thinner or alcohol benzene. • Do not subject the camera to high temperatures or high humidity. Do not leave the camera in a vehicle, as the temperature can get very high. • Do not store the camera with preservatives and chemicals. Storage in high temperatures and high humidity can cau ...

  • Pentax 1938507 - page 7

    Memo 5 ...

  • Pentax 1938507 - page 8

    6 FOR USING YOUR CAMERA SAFELY ...............................................1 ABOUT THE CAMERA .........................................................................1 PRECAUTIONS FOR BATTERY USAGE ............................................2 PRECAUTIONS FOR BATTERY CHARGER USAGE .........................3 Care to be Taken During Handling .... ...

  • Pentax 1938507 - page 9

    7 Basic Operations 53 Basic Shooting Operation ........................................................... 54 Holding the Camera ............................................................................54 Letting the Camera Choose the Optimal Settings .............................. 55 Using a Zoom Lens ........................................... ...

  • Pentax 1938507 - page 10

    8 Using Mirror Up Function to Prevent Camera Shake ............. 128 Changing the Shooting Conditions Automatically when Shooting (Auto Bracket) ............................................................ 129 Storing User Settings ................................................................ 133 Using the Flash 135 Compensating Flash Output ... ...

  • Pentax 1938507 - page 11

    9 Deleting Multiple Images ........................................................... 185 Deleting All Images ...........................................................................185 Deleting Selected Images (from Multi-image Display) ...................... 186 Deleting a Folder ............................................................... ...

  • Pentax 1938507 - page 12

    10 Setting the Image File Naming Convention ............................. 230 Selecting the Folder Name ............................................................... 230 Selecting the File Number Setting .................................................... 230 Setting the File Name ................................................................. ...

  • Pentax 1938507 - page 13

    11 This Operating Manual contains the following chapters. Composition of the Operating Manual 1 Before Using Your Camera Explains camera characteristics, accessories and the names and functions of various parts. 2 Getting Started Explains your first steps from purchasing the camera to taking pictures. Be sure to read it and follow the instructions. ...

  • Pentax 1938507 - page 14

    12 The symbols used in this Operating Manual are explained below. 1 Shows reference page number explaining a related operation. Shows useful information. Shows precautions to take when operating the camera. ...

  • Pentax 1938507 - page 15

    1 Before Using Your Camera Check the package contents and names and functions of working parts before use. u Camera Characteristics ........................ 14 Checking the Contents of the Package .............. 16 Names and Functions of Working Parts ............ 17 Display Indicators ................................................ 22 How to Oper ...

  • Pentax 1938507 - page 16

    14 Before Using Your Camera 1 u Camera Characteristics • Features a 23.4×15.6 mm CMOS sensor with approximately 14.6 million effective pixels for high precision and a wide dynamic range. • Features Shake Reduction (SR), an image sensor shifting shake reduction system. This enables you to capture sharp pictures with minimal camera shake regardl ...

  • Pentax 1938507 - page 17

    Before Using Your Camera 1 15 • Features Hyper-program and Hyper-manual modes that let you take pictures with the intended exposure. Also features Sensitivity Priority mode K that automatically adjusts aperture and shutter speed according to the set sensitivity, and Shutter & Aperture Priority mode L that automatically adjusts sensitivity acc ...

  • Pentax 1938507 - page 18

    16 Before Using Your Camera 1 Checking the Contents of the Package The following accessories are packaged with your camera. Check that all accessories are included. Hot shoe cover F K (Installed on camera) Eyecup F P (Installed on camera) ME Viewfinder cap Sync socket 2P cap (Installed on camera) Body mount cover (Installed on camera) USB cable I-U ...

  • Pentax 1938507 - page 19

    17 Before Using Your Camera 1 Names and Functions of Working Parts Camera Tripod socket Battery cover Self-Timer lamp/ Remote control receiver AF coupler Mirror Lens unlock button Lens information contacts Card cover Battery cover unlock lever Battery grip connector terminal cover Strap lug Hot shoe Lens mount index Card access lamp Built-in Flash ...

  • Pentax 1938507 - page 20

    18 Before Using Your Camera 1 Functions of buttons, dials and levers used during shooting are noted. * The factory default settings are explained here. Depending on the button or dial, these settings can be changed in the [ A Custom Settings] menu (p.73). Capture Mode 1 Green button Sets the Exposure mode to Automatic Exposure (p.85, p.92, p.95) an ...

  • Pentax 1938507 - page 21

    Before Using Your Camera 1 19 6 Focus mode lever Switches between autofocus mode ( k , l ) (p.104) and manual focus mode ( ) (p.110). 7 | button Saves JPEG and RAW file by default. (p.158, p.159) 8 K button Press to pop up the built-in flash. (p.60) 9 Mode dial Changes the Exposure mode. (p.32) 0 Metering mode lever Changes the Metering mode. (p. ...

  • Pentax 1938507 - page 22

    20 Before Using Your Camera 1 Functions of buttons, dials and levers used during playback are noted. * The factory default settings are explained here. Depending on the button or dial, these settings can be changed in the [ A Custom Settings] menu (p.73). Playback Mode 3 5 2 6 7 8 0 c d b a 4 1 9 ...

  • Pentax 1938507 - page 23

    Before Using Your Camera 1 21 1 Green button Press in Enlarged view to increase the magnification. (p.173) 2 Shutter release button Press halfway to switch to Capture mode. 3 Main switch Move to turn the camera on and off. (p.44) Set to the | position to switch to Capture mode and preview. 4 Front e-dial Use it to display the previous or next image ...

  • Pentax 1938507 - page 24

    22 Before Using Your Camera 1 Display Indicators The following indicators appear on the monitor depending on the status of the camera. Guides appear on the monitor for 3 seconds when the camera is switched on or the mode dial is turned. * Indicators 3, 5, 6 and 7 only appear when a setting other than the default setting is selected. 8 only appears ...

  • Pentax 1938507 - page 25

    Before Using Your Camera 1 23 Press the M button in Capture mode to display the capture function settings on the monitor for 30 seconds. Press the four-way controller ( 23 ) while displayed to switch to Detailed information display. Detailed information display (p.1) Capture Mode 1 Exposure mode (p.32) 16 ISO correction in AUTO (p.78) 2 USER mode ( ...

  • Pentax 1938507 - page 26

    24 Before Using Your Camera 1 Detailed information display (p.2) 1 Battery usage condition (p.234) 2 Camera battery power (p.38, p.234) 3 Grip battery power (p.38, p.234) 4 Button guide 5 e-dial guide AF Enable AF Enable AF Enable AF P LINE P LINE P LINE RAW RA W+ RA W+ RA W+ 1 5 4 3 2 ...

  • Pentax 1938507 - page 27

    Before Using Your Camera 1 25 Every time you press the M button during playback, the camera switches screen displays in the following order: Standard display, Histogram display, Detailed information display and No information display (image only). Detailed information display * Indicators 6 (Flash mode) and 14 (Flash exposure compensation) only app ...

  • Pentax 1938507 - page 28

    26 Before Using Your Camera 1 Histogram Display The u features two histogram displays. The “Brightness histogram” shows the distribution of brightness and the “RGB histogram” shows the distribution of color intensity. Press the four-way controller ( 23 ) to switch between “Brightness histogram” and “RGB histogram”. * Indicator 4 (DP ...

  • Pentax 1938507 - page 29

    Before Using Your Camera 1 27 Viewfinder 1 AF frame (p.52) 2 Spot metering frame (p.98) 3 AF point (p.107) 4 Flash status (p.60) Appears when flash is available and blinks when flash is recommended but not set or is being charged. 5 Shutter speed (p.76) Shutter speed when capturing or adjusting (underlined when shutter speed can be adjusted with th ...

  • Pentax 1938507 - page 30

    28 Before Using Your Camera 1 10 File format (p.158) Displays the image save format in RAW/RAW+ format. Not displayed in JPEG format. 11 EV compensation (p.100) Appears when EV compensation is available or in use. 12 Flash exposure compensation (p.136) Appears when Flash exposure compensation is in use. 13 Sensitivity display Appears when sensitivi ...

  • Pentax 1938507 - page 31

    Before Using Your Camera 1 29 The following information appears in the LCD panel on top of the camera. LCD Panel 1 Shutter speed (p.76) 6 Auto bracket (p.129) 2 Aperture (p.77) (blinks when Exposure Bracket and Extended Bracket are both set) 3 Flash mode (p.60) b : Built-in flash is ready 7 Flash exposure compensation (p.136) (when blinking, flash ...

  • Pentax 1938507 - page 32

    30 Before Using Your Camera 1 How to Operate the Menu This section explains operation methods for [ A Rec. Mode] menu, [ Q Playback] menu, [ R Set-up] menu and [ A Custom Setting] menu. 1 Press the 3 button in Capture mode. The [ A Rec. Mode] menu appears on the monitor. 2 Press the four-way controller ( 5 ). The [ Q Playback] menu, [ R Set-up] men ...

  • Pentax 1938507 - page 33

    Before Using Your Camera 1 31 Procedure to set the [JPEG Quality] on the [ A Rec. Mode] menu is explained as an example. 3 Use the four-way controller ( 23 ) to choose an item. Turn the front e-dial to navigate the menu a page at a time. 4 Press the four-way controller ( 5 ). Quality levels available when recording in JPEG format are displayed. Pre ...

  • Pentax 1938507 - page 34

    32 Before Using Your Camera 1 Using the Mode Dial You can switch the Exposure mode by setting the icons on the mode dial to the dial indicator. Item Function Page A (USER) Lets you capture images with settings that you set. p.133 B (Green) Automatically sets shutter speed and aperture to the proper exposure according to Program line when taking pic ...

  • Pentax 1938507 - page 35

    2 Getting Started This chapter explains your first steps from purchasing the camera to taking pictures. Be sure to read it and follow the instructions. Attaching the Strap .............................................. 34 Using the Battery .................................................. 35 Inserting/Removing the SD Memory Card .........40 Turnin ...

  • Pentax 1938507 - page 36

    34 Getting Started 2 Attaching the Strap 1 Pass the end of the strap through the strap lug, then secure it on the inside of the clasp. 2 Pass the other end of the strap through the other strap lug on the camera, then secure it on the inside of the clasp. ...

  • Pentax 1938507 - page 37

    35 Getting Started 2 Using the Battery Insert the battery into the camera. Use only a D-LI50 battery. When using the battery for the first time, or when the battery has not been used in a long time, or when [Battery depleted] appears, recharge the battery. Note: AC plug cord “Listed, Type SPT-2 or NISPT-2, 18/2 flexible cord, rated 125 V, 7A, min ...

  • Pentax 1938507 - page 38

    36 Getting Started 2 When using the battery for the first time, charge the battery and insert it into the camera. 1 Open the battery cover. Lift the battery cover unlock lever, turn towards OPEN ( 1 ) to unlock, and then pull the cover open ( 2 ). • Do not use the provided battery charger to charge batteries other than rechargeable lithium-ion ba ...

  • Pentax 1938507 - page 39

    37 Getting Started 2 2 Face the S mark on the battery towards the monitor, push the battery lock lever in the direction of the arrow ( 1 ) and insert the battery. Insert until the battery locks. To remove the battery, push the battery lock lever in the direction of the arrow ( 1 ) with your hand. The battery pops out slightly. Remove it. 3 Close th ...

  • Pentax 1938507 - page 40

    38 Getting Started 2 You can confirm remaining battery level by checking the { displayed on the LCD panel. The picture storage capacity (flash use 50%) is based on measuring conditions in accordance with CIPA standards and the others are based on PENTAX measuring conditions. Some deviation from the above figures may occur in actual use depending on ...

  • Pentax 1938507 - page 41

    39 Getting Started 2 We recommend using the AC adapter D-AC50 (optional) when using the monitor for a long time or when connecting to your PC. 1 Make sure the camera is turned off and open the terminal cover. 2 Face the S mark on the DC terminal of the AC adapter towards the S mark on the camera, and connect the DC terminal to the DC input terminal ...

  • Pentax 1938507 - page 42

    40 Getting Started 2 Inserting/Removing the SD Memory Card This camera uses either an SD Memory Card or an SDHC Memory Card. (Both cards are referred to as SD Memory Cards hereafter.) Make sure the camera is turned off before inserting or removing the SD Memory Card (market product). 1 Lift the card cover unlock lever ( 1 ) and turn it towards OPEN ...

  • Pentax 1938507 - page 43

    41 Getting Started 2 Precautions When Using the SD Memory Card • The SD Memory Card is equipped with a write-protect switch. Se tting the switch to LOCK protects the existing data by prohibiting recording of new data, deletion of existing data or formatting of the card. • Care should be taken when removing the SD Memory Card immediately after u ...

  • Pentax 1938507 - page 44

    42 Getting Started 2 Choose the number of pixels (size) and quality level (JPEG data compression rate) of pictures according to how you intend to use the pictures you have taken. Pictures with larger recorded pixels or more E s are clearer when printed. The number of pictures that can be taken (the number of pictures that can be recorded on an SD M ...

  • Pentax 1938507 - page 45

    43 Getting Started 2 With u , you can record in the versatile JPEG format or the high quality and editable RAW format. For RAW file format, you can select the PENTAX original PEF format or general-purpose DNG (Digital Negative) format designed by Adobe Systems. On a 512 MB SD Memory Card, you can record up to 20 images in PEF format or DNG format. ...

  • Pentax 1938507 - page 46

    44 Getting Started 2 Turning the Camera On and Off 1 Move the main switch to [ON] position. The camera will turn on. Move the main switch to [OFF] position to turn off the camera. • Always turn the camera off when not in use. • The power will automatically turn off when you do not perform any operations within a set period of time. To reactivat ...

  • Pentax 1938507 - page 47

    45 Getting Started 2 Initial Settings The first time the camera is turned on after purchasing, the [ Language/ ] screen appears on the monitor. Follow the procedure below to set the language displayed on the monitor and the current date and time. Once setting is done, these will not need to be set again when turning your camera on. If the Date Adju ...

  • Pentax 1938507 - page 48

    46 Getting Started 2 2 Press the 4 button. The [Initial Setting] screen for the selected language appears. Press the four-way controller ( 3 ) twice and proceed to Step 9 if [Hometown] does not have to be adjusted. 3 Press the four-way controller ( 3 ). The cursor moves to W . 4 Press the four-way controller ( 5 ) and use the four-way controller ( ...

  • Pentax 1938507 - page 49

    47 Getting Started 2 When an Incorrect Language is Set When you mistakenly select a language in the [Language/ ] screen, you can perform the following operations to set the correct language. 1 Press the 3 button once or twice to display the guides (p.22) on the monitor. The screen shown on the right is an example of the guides displayed. The displa ...

  • Pentax 1938507 - page 50

    48 Getting Started 2 Set the current date and time and the display style. 1 Press the four-way controller ( 5 ). The frame moves to [mm/dd/yy]. 2 Use the four-way controller ( 23 ) to choose the date style. 3 Press the four-way controller ( 5 ). The frame moves to [24h]. 4 Use the four-way controller ( 23 ) to select 24h (24-hour display) or 12h (1 ...

  • Pentax 1938507 - page 51

    49 Getting Started 2 7 Press the four-way controller ( 5 ). The frame moves to the month. 8 Use the four-way controller ( 23 ) to set the month. Set the day and year in the same manner. Next, set the time. If you select [12h] in Step 4, the setting switches between am and pm depending on the time. 9 Press the 4 button. The camera is ready to take a ...

  • Pentax 1938507 - page 52

    50 Getting Started 2 Attaching the Lens All camera exposure modes are available when using DA, D FA, FA J or other lenses with an Aperture s (Auto) position. Some functions are restricted when lenses are not set to the Aperture s position. Also see “Notes on [36. Using Aperture Ring]” (p.251). Other lenses and accessories will not be available ...

  • Pentax 1938507 - page 53

    51 Getting Started 2 4 Remove the front lens cap by pushing the indicated portions inward. To detach the lens, hold down the lens unlock button ( 3 ) and turn the lens counterclockwise. • The body mount cover ( 1 ) is a cover to prevent scratches and block dust when shipped. Body Mount Cap K is sold separately and has a lock function. • We assu ...

  • Pentax 1938507 - page 54

    52 Getting Started 2 Adjusting the Viewfinder Diopter Adjust the viewfinder to suit your eyesight. If it is difficult to see the viewfinder image clearly, slide the diopter adjustment lever sideways. You can adjust the diopter from approximately –2.5m -1 to +1.5m -1 . 1 Look through the viewfinder and point the camera at a white wall or other bri ...

  • Pentax 1938507 - page 55

    3 Basic Operations This chapter explains basic operations for shooting by setting mode dial to Green mode (automatic exposure according to the Normal program line) to ensure successful capturing. For information about advanced functions and settings for taking pictures, refer to chapter 4 and onward. Basic Shooting Operation ....................... ...

  • Pentax 1938507 - page 56

    54 Basic Operations 3 Basic Shooting Operation How you hold the camera is important when taking pictures. • Hold the camera firmly with both hands. • Press the shutter release button gently when taking a picture. Holding the Camera • To reduce camera shake, support your body or the camera on a solid object such as a table, tree, or wall. • ...

  • Pentax 1938507 - page 57

    55 Basic Operations 3 The u features various Capture modes, Focus modes, and Drive modes suited for your intentions. This section explains how to take pictures by simply pressing the shutter release button. 1 Set the mode dial to B . The Exposure mode changes to B (Green) mode. In B , proper exposure is determined by the camera and the shutter spee ...

  • Pentax 1938507 - page 58

    56 Basic Operations 3 3 Look through the viewfinder to view the subject. A zoom lens can be used to change the size of the subject in the viewfinder. 1 Using a Zoom Lens (p.59) 4 Position the subject inside the AF frame and press the shutter release button halfway. The autofocus system operates. The focus indicator ] appears in the viewfinder when ...

  • Pentax 1938507 - page 59

    57 Basic Operations 3 6 Review the captured image on the monitor. Image appears for 1 second on the monitor after capturing (Instant Review). You can magnify the image during Instant Review with the rear e-dial. (p.174) You can delete the image during Instant Review by pressing the i button. 1 Setting the Instant Review (p.227) 1 Deleting Images (p ...

  • Pentax 1938507 - page 60

    58 Basic Operations 3 The autofocus mechanism is not perfect. Focusing may be difficult when taking pictures under the following conditions ((a) to (f) below). These also apply to manual focusing using the focus indicator ] in the viewfinder. If the subject cannot be focused automatically, set the focus mode lever to and use the manual focus mode ...

  • Pentax 1938507 - page 61

    59 Basic Operations 3 Using a Zoom Lens Enlarge the subject (telephoto) or capture a wider area (wide angle) with a zoom lens. Adjust it to the desired size and take the picture. 1 Turn the zoom ring to the right or left. Turn the zoom ring clockwise for telephoto and counterclockwise for wide angle. • The smaller the number of the displayed foca ...

  • Pentax 1938507 - page 62

    60 Basic Operations 3 Using the Built-in Flash If you wish to discharge the flash in a dark or backlit location, press the K button to pop up the flash. Select a flash mode to suit your purpose from the Flash options screen in the Fn menu. You can adjust the flash output with the rear e-dial in any Exposure mode other than Green mode. The built-in ...

  • Pentax 1938507 - page 63

    61 Basic Operations 3 1 Press the { button. The Fn menu appears. When using Slow-speed sync or Slow-speed sync+Red-eye, the shutter speed becomes slower depending on the brightness. Use Shake Reduction (p.65) or fix the camera on a tripod to prevent camera shake. Selecting Flash Mode Exit Exit Exit Fn AUTO AUTO AUTO OK Fn CUSTOM IMAGE ...

  • Pentax 1938507 - page 64

    62 Basic Operations 3 2 Press the four-way controller ( 3 ). The Flash options screen appears. 3 Use the four-way controller ( 45 ) to choose a flash mode. When not in B (Green) mode, turn the rear e-dial to perform Flash exposure compensation. (p.136) 4 Press the 4 button. The camera is ready to take a picture. • When the mode dial is set to B , ...

  • Pentax 1938507 - page 65

    63 Basic Operations 3 1 Press the K button. The built-in flash pops up and begins charging. When the flash is fully charged, E appears in the LCD panel and viewfinder. (p.27, p.29) 2 Press the shutter release button halfway. The focus indicator ] appears in the viewfinder when focused. 3 Press the shutter release button fully. The picture is taken. ...

  • Pentax 1938507 - page 66

    64 Basic Operations 3 “Red-eye” is the phenomenon where eyes look reddish in photographs taken in dark environments with a flash. This is caused by the reflection of the electronic flash in the retina of the eye. Red-eye occurs because pupils are dilated in dark environments. This phenomenon cannot be averted but the following measures can be u ...

  • Pentax 1938507 - page 67

    65 Basic Operations 3 Taking Pictures Using the Shake Reduction Function You can easily take sharp pictures using the Shake Reduction function by simply turning on the Shake Reduction switch. Shake Reduction The Shake Reduction function reduces camera shake that occurs when the shutter release button is pressed. This is useful for taking pictures i ...

  • Pentax 1938507 - page 68

    66 Basic Operations 3 1 Turn on the Shake Reduction switch. When the shutter release button is pressed halfway, k appears in the viewfinder and the Shake Reduction function turns on. Turning On the Shake Reduction Function • Be sure to turn off the Shake Reduction switch when using the camera with a tripod. • The Shake Reduction function automa ...

  • Pentax 1938507 - page 69

    67 Basic Operations 3 The [Input Focal Length] setting menu appears when the camera is turned on with the Shake Reduction switch on and a type of lens that does not support automatic acquisition of lens information such as focal length (p.65) is mounted. Set [Focal Length] manually on the [Input Focal Length] setting menu. 1 Use the four-way contro ...

  • Pentax 1938507 - page 70

    68 Basic Operations 3 Playing Back Still Pictures You can play back captured still pictures with the camera. 1 Press the Q button after taking a picture. The most recently captured image (image with the largest file number) is displayed on the monitor. Press the M button during playback to display information such as the image data for the displaye ...

  • Pentax 1938507 - page 71

    69 Basic Operations 3 2 Press the four-way controller ( 45 ). 4 : The previous image appears. 5 : The next image appears. • You can display the next or previous image by turning the front e-dial. • Refer to “Playback Functions” (p.169) for playback mode details. ...

  • Pentax 1938507 - page 72

    70 Basic Operations 3 Deleting Images You can delete one image at a time. 1 Press the Q button and use the four-way controller ( 45 ) to select an image to delete. 2 Press the i button. The Delete screen appears. 3 Use the four-way controller ( 23 ) to select [Delete]. Select the file format to delete for images saved in RAW+ format. 4 Press the 4 ...

  • Pentax 1938507 - page 73

    4 Shooting Functions This chapter describes the various basic and advanced shooting functions available with the u . How to Operate the Shooting Menus .................72 Setting the Exposure ........................................... 76 Focusing ............................................................. 104 Checking the Composition, Exposure a ...

  • Pentax 1938507 - page 74

    72 Shooting Functions 4 How to Operate the Shooting Menus Press the 3 button in Capture mode. The [ A Rec. Mode] menu appears. Perform settings related to capturing in the [ A Rec. Mode] menu. [ A Rec. Mode] Menu Setting Items Item Function Page Exposure Mode Sets the Exposure mode. * Appears only when the mode dial is set to A . p.133 JPEG Recorde ...

  • Pentax 1938507 - page 75

    73 Shooting Functions 4 Set custom functions to fully use the functions of a SLR camera with the Custom Setting Menu. The default setting does not change custom function. The [ A Custom Setting] menu settings are activated when [Setting], the first item, is O (On). [ A Custom Setting] Menu Setting Items Item Function Page Setting Sets to change cus ...

  • Pentax 1938507 - page 76

    74 Shooting Functions 4 14. AF by Press Halfway Sets whether to perform AF when the shutter release button is pressed halfway. - 15. Superimpose AF Area Sets whether to display the selected AF point (focus position) in the viewfinder. p.107 16. AF in remote control Sets whether to use Autofocus when shooting with remote control. Shutter releases af ...

  • Pentax 1938507 - page 77

    75 Shooting Functions 4 Press the { button in Capture mode. The Fn menu appears. Press the four-way controller ( 2345 ) or the 4 button to set the operation. 31. Display Sensitivity Sets whether to switch the number of recordable images in the LCD panel and viewfinder to the sensitivity display. - 34. Catch-in focus When set to [On], if the focus m ...

  • Pentax 1938507 - page 78

    76 Shooting Functions 4 Setting the Exposure Correct exposure of the subject is determined by the combination of shutter speed and aperture setting. There are many correct combinations of shutter speed and aperture for a particular subject. Different combinations produce different effects. The shutter speed determines the length of time that light ...

  • Pentax 1938507 - page 79

    77 Shooting Functions 4 Adjust the amount of light hitting the CMOS sensor by changing the aperture. Opening the aperture (reduce the aperture value) Objects closer and farther than the focused subject will be more out of focus. For instance, if you take a picture of a flower against a landscape with the aperture open, the landscape in front and be ...

  • Pentax 1938507 - page 80

    78 Shooting Functions 4 You can set the sensitivity to suit the brightness of the surroundings. The sensitivity can be set to [AUTO] or within a sensitivity range equivalent to ISO 100 to 3200. The default setting is [AUTO]. Set [Sensitivity] in the Fn menu. (p.75) Set range to automatically correct sensitivity when Sensitivity is set to [AUTO]. Th ...

  • Pentax 1938507 - page 81

    79 Shooting Functions 4 Press the 4 button in Capture mode. The set sensitivity is displayed on the LCD panel and in the viewfinder. Turn the front e-dial while pressing the 4 button to change the sensitivity. Dynamic range is the ratio that indicates the light level expressed by the CMOS sensor pixels from bright areas to dark areas. By using the ...

  • Pentax 1938507 - page 82

    80 Shooting Functions 4 This camera features the following nine exposure modes. Use the mode dial (p.32) to change the exposure mode. The settings available for each exposure mode are as follows. Changing the Exposure Mode Exposure Mode Description EV Com- pensation Change Shutter Speed Change Aperture Sen- sitivity Page B (Green) Automatically set ...

  • Pentax 1938507 - page 83

    81 Shooting Functions 4 e (Hyper- program) Automatically sets shutter speed and aperture to the proper exposure according to Program line when taking pictures. You can use the front and rear e-dials to easily switch between shutter priority and aperture priority. Yes Yes Yes Yes p.84 K (Sensitivity Priority) Automatically sets the shutter speed and ...

  • Pentax 1938507 - page 84

    82 Shooting Functions 4 * Refer to p.101 for details on EV compensation for a (Hyper-manual) and M (Flash X-sync speed). M (Flash X- sync speed) The shutter speed is locked at 1/180 seconds. Use this when using an External flash that does not automatically change the shutter speed. Yes* No Yes Other than Auto p.97 Exposure Mode Description EV Com- ...

  • Pentax 1938507 - page 85

    83 Shooting Functions 4 Automatically sets shutter speed and aperture to the proper exposure according to Program line when taking pictures. 1 Set the mode dial to B . 2 Confirm the shutter speed and aperture in the viewfinder or on the LCD panel. Using the B (Green) Mode Shutter speed, aperture, AE lock, EV compensation, Auto bracket, Multi- expos ...

  • Pentax 1938507 - page 86

    84 Shooting Functions 4 Automatically sets shutter speed and aperture to the proper exposure according to Program line when taking pictures. Use the front e-dial and rear e-dial to change the shutter speed and aperture while maintaining the proper exposure (Hyper-program). 1 Set the mode dial to e . 2 Confirm the shutter speed and aperture in the v ...

  • Pentax 1938507 - page 87

    85 Shooting Functions 4 You can set the sensitivity to suit the brightness of the subject. The shutter speed and aperture are automatically set according to the selected sensitivity to obtain the appropriate exposure. 1 Set the mode dial to K . Using the K (Sensitivity Priority) Mode Hyper-program To change the shutter speed You can switch to Shutt ...

  • Pentax 1938507 - page 88

    86 Shooting Functions 4 2 Turn the rear e-dial and adjust the sensitivity. The shutter speed, aperture value and sensitivity are displayed in the viewfinder and on the LCD panel. • You can set the sensitivity to values equivalent to ISO 100 to 3200. [AUTO] is not available. • Turn the front e-dial while pressing the m button to change the EV co ...

  • Pentax 1938507 - page 89

    87 Shooting Functions 4 Lets you set the desired shutter speed for expressing moving subjects. When taking pictures of a fast moving subject, you can increase the shutter speed to make the subject look still or decrease the shutter speed to have the subject show movement. Aperture value is automatically set to give the appropriate exposure dependin ...

  • Pentax 1938507 - page 90

    88 Shooting Functions 4 • Turn the front e-dial while pressing the m button to change the EV compensation value. (p.100) • Set the shutter speed in increments of 1/2 EV or 1/3 EV. Set in [2. EV Steps] in the [ A Custom Setting] menu. (p.101) • You can automatically correct the sensitivity if appropriate exposure cannot be set with the set cri ...

  • Pentax 1938507 - page 91

    89 Shooting Functions 4 Set aperture for controlling the depth of field. The depth of field is deeper and the front and back of the focused object is clear when aperture is set to a large value. The depth of field is shallower and the front and back of the focused object is blurred when aperture is set to a small value. Shutter speed is automatical ...

  • Pentax 1938507 - page 92

    90 Shooting Functions 4 • Turn the front e-dial while pressing the m button to change the EV compensation value. (p.100) • Set the aperture value in increments of 1/2 EV or 1/3 EV. Set in [2. EV Steps] in the [ A Custom Setting] menu. (p.101) • You can automatically correct the sensitivity if appropriate exposure cannot be set with the set cr ...

  • Pentax 1938507 - page 93

    91 Shooting Functions 4 You can set both the desired shutter speed and aperture to take the picture. Automatically sets the sensitivity so that the manually set shutter speed and aperture will give the proper exposure according to the brightness of the subject. 1 Set the mode dial to L . 2 Turn the front e-dial and adjust the shutter speed. 3 Turn ...

  • Pentax 1938507 - page 94

    92 Shooting Functions 4 • Turn the front e-dial while pressing the m button to change the EV compensation value. (p.100) • Set the shutter speed and aperture values in increments of 1/2 EV or 1/3 EV. Set in [2. EV Steps] in the [ A Custom Setting] menu. (p.101) • Settings other than [AUTO] are not available in [Sensitivity] in the Fn menu. ? ...

  • Pentax 1938507 - page 95

    93 Shooting Functions 4 This mode is convenient for taking pictures using the same shutter speed and aperture setting combination or taking intentionally underexposed (darker) or over-exposed (brighter) photographs. 1 Effect of Aperture and Shutter Speed (p.76) 1 Set the mode dial to a . 2 Press the Green button. Automatically switches shutter spee ...

  • Pentax 1938507 - page 96

    94 Shooting Functions 4 • When the sensitivity is set to [AUTO] and exposure mode is set to a (Hyper- manual) mode, the sensitivity is the lowest sensitivity set in “Setting the Range of Automatic Correction in AUTO” (p.78). • The viewfinder indicator blinks when the difference from appropriate exposure is over ±3.0. • Set the shutter sp ...

  • Pentax 1938507 - page 97

    95 Shooting Functions 4 Combining with L Press the L button (p.102) to record the exposure value in Hyper-manual. If the shutter speed or aperture is then changed, the combination of shutter speed and aperture changes while exposure is retained. Example: If the shutter speed is 1/125 sec and aperture is F5.6 and is recorded with the L button, and t ...

  • Pentax 1938507 - page 98

    96 Shooting Functions 4 This mode is useful for the long exposures required for shooting night scenes and fireworks. The shutter remains open as long as the shutter release button is kept pressed. 1 Set the mode dial to p . Using the p (Bulb) Mode • EV compensation, Continuous shooting and Exposure Bracket are not available in p (Bulb) mode. • ...

  • Pentax 1938507 - page 99

    97 Shooting Functions 4 The shutter speed is locked at 1/180 seconds. Use this when using an External flash that does not automatically change the shutter speed. 1 Set the mode dial to M . Using the M (Flash X-Sync Speed) Mode • Turn the rear e-dial to adjust the aperture value. • Press the Green button to retain the shutter speed at 1/180 sec ...

  • Pentax 1938507 - page 100

    98 Shooting Functions 4 Choose the part of the screen to use for measuring brightness and determining exposure. L (Multi-segment metering), M (Center-weighted metering) or N (Spot metering) mode can be selected. The factory default setting is L (Multi-segment metering). Set with the metering mode lever. (p.19) The scene in the viewfinder is metered ...

  • Pentax 1938507 - page 101

    99 Shooting Functions 4 Metering is weighted at the center of the screen. Use this metering when you want to compensate the exposure by experience, instead of leaving it to the camera. The illustration shows that sensitivity increases as the pattern height increases (center). This mode does not automatically compensate for backlit scenes. With spot ...

  • Pentax 1938507 - page 102

    100 Shooting Functions 4 This allows you to deliberately overexpose (brighten) or under-expose (darken) your picture. Select 1/2 EV or 1/3 EV in [2. EV Steps] in the [ A Custom Setting] menu. (p.101) You can adjust the EV Compensation from –3 to +3 (EV) in increments of 1/2 EV or –2 to +2 (EV) in increments of 1/3 EV. 1 Set the compensation wit ...

  • Pentax 1938507 - page 103

    101 Shooting Functions 4 Set Exposure Steps in [ 2. EV Steps ] in the [ A Custom Setting] menu to increments of 1/2 EV or 1/3 EV. EV compensation is not available when the exposure mode is set to B (Green) or p (Bulb) mode. • The EV compensation cannot be canceled by turning the camera off or by setting any other exposure mode. • The EV compens ...

  • Pentax 1938507 - page 104

    102 Shooting Functions 4 AE Lock is a function that memorizes the exposure prior to taking the picture. Use this when the subject is too small or backlit and a proper exposure setting cannot be obtained. 1 Press the L button. The camera memorizes the exposure (brightness) at that instant. Press it again to unlock. Recording the Exposure Before Shoo ...

  • Pentax 1938507 - page 105

    103 Shooting Functions 4 You can take multiple frames while creating a single picture. 1 Select [Multi-exposure] in the [ A Rec. Mode] menu and press the four-way controller ( 5 ). The Multi-exposure screen appears. 2 Use the four-way controller ( 5 ) to select the number of shots. Use the four-way controller ( 23 ) to select from 2 to 9 shots. 3 P ...

  • Pentax 1938507 - page 106

    104 Shooting Functions 4 Focusing You can focus with the following methods. You can also choose the autofocus mode from l (Single mode) where the shutter release button is pressed halfway to focus on the subject and the focus is locked at that position, and k (Continuous mode) where the subject is kept in focus by continuous adjustment while the sh ...

  • Pentax 1938507 - page 107

    105 Shooting Functions 4 2 Look through the viewfinder and press the shutter release button halfway. The focus indicator ] appears in the viewfinder when focused. (When blinking, the subject is not in focus.) 1 Subjects that are Difficult to Focus on (p.58) • The camera can be focused by pressing the = button as well as by pressing the shutter re ...

  • Pentax 1938507 - page 108

    106 Shooting Functions 4 AF Adjustment You can adjust the AF focusing position with [35. AF Adjustment] in the [ A Custom Setting] menu. 1 Select [35. AF Adjustment] in the [ A Custom Setting] menu and press the four-way controller ( 5 ). 2 Press the four-way controller ( 23 ) to select [On] and press the four-way controller ( 5 ). The AF Adjustmen ...

  • Pentax 1938507 - page 109

    107 Shooting Functions 4 Choose the part of the viewfinder to set focus to. The factory default setting is S (Auto). The selected AF point lights red in the viewfinder. (Superimpose AF Area) Set with the AF point switching dial. (p.19) 1 Select j (Select) with the AF point switching dial. Selecting the Focusing Area (AF Point) S Auto The camera sel ...

  • Pentax 1938507 - page 110

    108 Shooting Functions 4 2 Look through the viewfinder and check the position of the subject. 3 Use the four-way controller ( 2345 ) to select the desired AF point. The AF point lights red in the viewfinder (Superimpose AF Area) and you can check where you set the AF point. If the subject is outside the range of the focusing area, the camera cannot ...

  • Pentax 1938507 - page 111

    109 Shooting Functions 4 2 Center the subject to focus in the viewfinder and press the shutter release button halfway. The focus indicator ] appears and you will hear a beep when the subject comes into focus. (When blinking, the subject is not in focus.) 3 Lock the focus. Keep the shutter release button pressed halfway. The focus will remain locked ...

  • Pentax 1938507 - page 112

    110 Shooting Functions 4 Set [6. AE-L with AF locked] in the [ A Custom Setting] menu (p.73) to lock the exposure value while focus is locked. Exposure is not locked by default during focus lock. When you adjust the focus manually, you can either check with the focus indicator in the viewfinder or use the viewfinder matte field to adjust focus. The ...

  • Pentax 1938507 - page 113

    111 Shooting Functions 4 2 Look through the viewfinder, press the shutter release button halfway and turn the focusing ring. The focus indicator ] appears and you will hear a beep when the subject comes into focus. You can manually adjust the focus using the viewfinder matte field. 1 Set the focus mode lever to . • Focus manually using the matt ...

  • Pentax 1938507 - page 114

    112 Shooting Functions 4 2 Look through the viewfinder and turn the focusing ring until the subject looks sharp on the focusing screen. The = button operates the autofocus mechanism in the same manner as when the shutter release button is pressed halfway. (Capturing is performed with the shutter release button.) When the subject is focused with the ...

  • Pentax 1938507 - page 115

    113 Shooting Functions 4 Checking the Composition, Exposure and Focus Before Shooting You can use the preview function to check the depth of field, composition, exposure and focus before taking a picture. There are 3 preview methods. Choose whether to use Live View, Optical Preview, or Digital Preview when the main switch is turned to the preview p ...

  • Pentax 1938507 - page 116

    114 Shooting Functions 4 1 Focus on the subject, and then turn the main switch to | . The mirror raises and a real-time image is displayed on the monitor. Turn the main switch to | again to exit Live View. Live View can be displayed for up to 3 minutes. Displaying the Preview Displaying the Live View • If Live View is used in places where the cam ...

  • Pentax 1938507 - page 117

    115 Shooting Functions 4 1 Position the subject inside the AF frame and press the shutter release button halfway to focus on the subject. 2 Turn the main switch to | while looking through the viewfinder. You can check the depth of field in the viewfinder while the main switch is on | . 1 Focus on the subject, then compose the picture in the viewfin ...

  • Pentax 1938507 - page 118

    116 Shooting Functions 4 • You can display the Bright/Dark area warning or histogram in Digital Preview. Set in [Digital Preview] (p.229) in the [ Q Playback] menu. • The maximum display time for Digital Preview is 60 seconds. • You can magnify the image during Digital Preview with the rear e-dial. (p.174) • Press the { button during Digita ...

  • Pentax 1938507 - page 119

    117 Shooting Functions 4 Continuous Shooting Pictures can be taken continuously while the shutter release button is held down. You can select from g (Continuous shooting (Hi)) and h (Continuous shooting (Lo)) for continuous shooting. 1 Press the { button. The Fn menu appears. 2 Press the four-way controller ( 2 ). The Drive Mode options screen appe ...

  • Pentax 1938507 - page 120

    118 Shooting Functions 4 4 Press the four-way controller ( 3 ) and use the four-way controller ( 45 ) to select g or h . 5 Press the 4 button. The camera is ready to take pictures continuously. 6 Press the shutter release button halfway. The autofocus system operates. The focus indicator ] appears in the viewfinder when focused. 7 Press the shutter ...

  • Pentax 1938507 - page 121

    119 Shooting Functions 4 You can take pictures continuously at approximately 21 frames per second. In this mode, images are saved with JPEG Quality set to Y (1536×1024) regardless of the save format setting (p.156). The JPEG Quality set in the [ A Rec. Mode] menu is used. 1 Press the { button. The Fn menu appears. 2 Press the four-way controller ( ...

  • Pentax 1938507 - page 122

    120 Shooting Functions 4 Interval Shooting During interval shooting, pictures are taken at a set interval from a set time. 1 Select [Interval Shooting] in the [ A Rec. Mode] menu. 2 Press the four-way controller ( 5 ). 3 Use the four-way controller ( 45 ) to select O (On). 4 Use the four-way controller ( 3 ) to select [Interval]. When taking two or ...

  • Pentax 1938507 - page 123

    121 Shooting Functions 4 7 Press the 4 button. The camera is ready to take a series of interval pictures. 8 Press the shutter release button halfway. The focus indicator ] appears when the subject is in focus. 9 Press the shutter release button fully. When [Start Trigger] is set to [Now], the first picture is taken. When set to [Set Time], shooting ...

  • Pentax 1938507 - page 124

    122 Shooting Functions 4 Self-Timer Shooting This camera has two types of self-timers: g and Z . 1 Mount the camera onto a tripod. 2 Press the { button. The Fn menu appears. 3 Press the four-way controller ( 2 ). The Drive Mode options screen appears. 4 Use the four-way controller ( 45 ) to select g . g Shutter will be released after about 12 secon ...

  • Pentax 1938507 - page 125

    123 Shooting Functions 4 5 Press the four-way controller ( 3 ) and use the four-way controller ( 45 ) to select g or Z . 6 Press the 4 button. The camera is ready to take a picture. 7 Confirm in the viewfinder that the subject you wish to shoot is properly framed and press the shutter release button halfway. The focus indicator ] appears when the s ...

  • Pentax 1938507 - page 126

    124 Shooting Functions 4 • The beep can be turned off (p.219). • Exposure may be affected if light enters the viewfinder. Attach the provided ME viewfinder cap or use the AE lock function (p.102). (To ignore the light entering the viewfinder, set the exposure mode to a (Hyper-manual) (p.93).) • Select a setting other than g or Z in the Drive ...

  • Pentax 1938507 - page 127

    125 Shooting Functions 4 Remote Control Shooting (Remote Control F: Sold Separately) The shutter can be released from a distance by using the optional remote control unit. You can select from h (remote control), i (3 sec. delayed release), or i (remote continuous shooting) for remote control shooting. 1 Mount the camera onto a tripod. 2 Press the { ...

  • Pentax 1938507 - page 128

    126 Shooting Functions 4 5 Press the four-way controller ( 3 ) and use the four-way controller ( 45 ) to select h , i , or i . The self-timer lamp will blink to let you know that the camera is in remote control wait status. 6 Press the 4 button. The camera is ready to take a picture. 7 Press the shutter release button halfway. The autofocus system ...

  • Pentax 1938507 - page 129

    127 Shooting Functions 4 • Exposure may be affected if light enters the viewfinder. Attach the provided ME viewfinder cap or use the AE lock function (p.102). (To ignore the light entering the viewfinder, set the exposure mode to a (Hyper-manual) (p.93).) • Select a setting other than h , i or i in the Drive Mode options screen to stop the remo ...

  • Pentax 1938507 - page 130

    128 Shooting Functions 4 Using Mirror Up Function to Prevent Camera Shake Use the Mirror Up function if camera shake is evident even when cable switch (optional) or remote control unit (optional) is used with a tripod. When shooting with the 2 sec. Self-Timer, the mirror pops up and the shutter is released 2 seconds after you press it, thereby avoi ...

  • Pentax 1938507 - page 131

    129 Shooting Functions 4 Changing the Shooting Conditions Automatically when Shooting (Auto Bracket) You can take continuous pictures with different exposure when the shutter release button is pressed. The first frame is exposed with no compensation, the second frame is underexposed (negative compensation) and the third is overexposed (positive com ...

  • Pentax 1938507 - page 132

    130 Shooting Functions 4 2 Set the step interval. Turn the rear e-dial while pressing the ] button. The available bracketing amounts in [2. EV Steps] in the [ A Custom Setting] menu (p.73) are as follows. 3 Press the shutter release button halfway. The focus indicator ] appears in the viewfinder when focused. 4 Press the shutter release button full ...

  • Pentax 1938507 - page 133

    131 Shooting Functions 4 You can save pictures with three different white balance, saturation, hue, sharpness and contrast levels. Unlike exposure bracketing, three pictures are saved with each shot. You can set the saving order with [9. Auto Bracketing order] in the [ A Custom Setting] menu. 1 Select [Extended Bracket] in the [ A Rec. Mode] menu a ...

  • Pentax 1938507 - page 134

    132 Shooting Functions 4 5 Press the four-way controller ( 3 ) to select [Bracketing amount] and press the four-way controller ( 5 ). Use the four-way controller ( 23 ) to select the bracketing amount. For [White Balance], select from BA±1, BA±2, BA±3, GM±1, GM±2 and GM±3. The default setting is BA±1. For [Saturation], [Hue], [Contrast] and ...

  • Pentax 1938507 - page 135

    133 Shooting Functions 4 Storing User Settings You can store the current camera settings and easily retrieve them simply by setting the mode dial to A . The following settings can be stored. Store the settings in [USER] in the [ R Set-up] menu. You can also perform settings when the mode dial is set to A . To change the Exposure Mode, press the 3 b ...

  • Pentax 1938507 - page 136

    Memo 134 ...

  • Pentax 1938507 - page 137

    5 Using the Flash This chapter provides details on the built-in flash of u and describes how to take pictures with the external flash. Compensating Flash Output ............................. 136 Allowing Shooting while Charging Flash ......... 137 Flash Characteristics in Each Exposure Mode .......................................................... ...

  • Pentax 1938507 - page 138

    136 Using the Flash 5 Compensating Flash Output You can change the flash output in a range of –2.0 to +1.0. The flash compensation values are as follows for 1/2 EV and 1/3 EV. * Set interval of steps in [2. EV Steps] in the [ A Custom Setting] menu. (p.101) Turn the rear e-dial to set [Flash Mode] in the Fn menu (p.75). Step interval Flash compen ...

  • Pentax 1938507 - page 139

    137 Using the Flash 5 Allowing Shooting while Charging Flash You can set to enable shooting while flash is being charged. Set [On] for [28. Release when Charging] in the [ A Custom Setting] menu (p.74). Pictures cannot be taken while the flash is charging by default. 28. Release when Charging Enables shutter release while the built-in flash is char ...

  • Pentax 1938507 - page 140

    138 Using the Flash 5 Flash Characteristics in Each Exposure Mode • When taking a moving subject, you can use the flash to change the blur effect. • Any desired shutter speed 1/180 sec. or slower can be set for taking a flash photograph. • The aperture value automatically changes according to the ambient brightness. • The shutter speed is l ...

  • Pentax 1938507 - page 141

    139 Using the Flash 5 You can use slow-speed sync when shooting portraits with the sunset in the background. Both the portrait and the background are captured beautifully. Using e / K / c mode 1 Set the mode dial to e , K or c . 2 Press the K button. 3 Press the { button and press the four-way controller ( 3 ). 4S e l e c t G or H and press the 4 b ...

  • Pentax 1938507 - page 142

    140 Using the Flash 5 Trailing curtain sync discharges the flash immediately before the shutter curtain closes. When shooting moving objects with a slow shutter speed, Trailing curtain sync and Slow-speed sync produce different effects depending on when the flash is discharged. For example, when shooting a moving car with Trailing curtain sync, tra ...

  • Pentax 1938507 - page 143

    141 Using the Flash 5 Distance and Aperture when Using the Built-in Flash A set criteria is necessary between the guide number, aperture and distance when shooting with the flash to obtain the correct exposure. Calculate and adjust the shooting conditions if flash output is not sufficient. Built-in flash guide number The following equation calculat ...

  • Pentax 1938507 - page 144

    142 Using the Flash 5 DA, D FA, FA J, FA and F Lens Compatibility with the Built-in Flash Depending on the lens used with the u , even if a lens without a hood is attached, the use of the built-in flash may not be possible or may be limited due to vignetting. DA, D FA, FA J, and FA lenses not listed below can be used without problems. * Following a ...

  • Pentax 1938507 - page 145

    143 Using the Flash 5 Using an External Flash (Optional) Using the optional external flash AF540FGZ, AF360FGZ or AF200FG enables a variety of flash modes, such as P-TTL auto flash mode, depending on the external flash being used. See the chart below for details. (Yes: Available #: Restricted No: Not available) *1 When using DA, D FA, FA J, FA, F or ...

  • Pentax 1938507 - page 146

    144 Using the Flash 5 The AF360FGZ does not have the function to set the FORMAT size to [DIGITAL], but the difference in angle of view between standard 35 mm format and the u is automatically calculated based on the focal length of the lens used (when using DA, D FA, FA J, FA or F lenses). The conversion indicator appears and the format size indica ...

  • Pentax 1938507 - page 147

    145 Using the Flash 5 With the AF540FGZ or AF360FGZ, you can discharge the flash to take a picture at a shutter speed faster than 1/180 second. High-speed flash sync can be used with the flash attached to the camera, or wireless. Attaching and Using the AF540FGZ or AF360FGZ on the Camera 1 Remove the cover of the hot shoe and attach the external fl ...

  • Pentax 1938507 - page 148

    146 Using the Flash 5 Setting the Channel for the External Flash on the Camera First set the channel for the external flash unit on the camera. 1 Set the channel for the external flash unit. 2 Attach the external flash to the camera hot shoe. 3 Turn on the camera and the external flash, and press the shutter release button halfway. The built-in fla ...

  • Pentax 1938507 - page 149

    147 Using the Flash 5 Wireless Shooting Using a Combination of the Built-in Flash and an External Flash Unit 1 Remove the external flash unit for which the channel was set on the camera, and place at the desired location. 2 Set the flash mode of the camera to r , and pop up the built-in flash. 3 Confirm that both flashes are fully charged and then ...

  • Pentax 1938507 - page 150

    148 Using the Flash 5 As with the built-in flash, red-eye reduction is available with an external flash.This may not be available on some flashes or may have restrictions for usage conditions. See the chart on p.143. When using the built-in flash with an external flash (AF540FGZ or AF360FGZ) that is set to the Trailing curtain sync function, the bu ...

  • Pentax 1938507 - page 151

    149 Using the Flash 5 As shown in the illustration below, attach the Hot Shoe Adapter F G (optional) to the camera hot shoe and an Off-Camera Shoe Adapter F (optional) to the bottom of the external flash, and connect these with the Extension Cord F5P (optional). The Off-Camera Shoe Adapter F can be mounted using the tripod screw to your tripod. Onl ...

  • Pentax 1938507 - page 152

    150 Using the Flash 5 When combining two or more external flashes Combining two or more external flashes (AF540FGZ, AF360FGZ or AF200FG) or using an external flash in combination with the built-in flash allows multiple flash photography (contrast-control-sync flash photography). This is based on the difference between the amounts of light discharge ...

  • Pentax 1938507 - page 153

    151 Using the Flash 5 You can connect an external flash to the camera with a sync cord by using the X-sync socket. X-sync Socket • The use of high-voltage or high-current external flashes may cause a camera breakdown. • When a cord is connected to the X-sync socket, linked functions will not work. • To prevent vignetting caused from Trailing ...

  • Pentax 1938507 - page 154

    Memo 152 ...

  • Pentax 1938507 - page 155

    6 Shooting Settings This chapter describes how to set the save format for pictures taken and other settings. Setting the Image Processing Method in Capture Mode (Custom Image) ........................................ 154 Setting the File Format ......................................156 ...

  • Pentax 1938507 - page 156

    154 Shooting Settings 6 Setting the Image Processing Method in Capture Mode (Custom Image) By using Custom Image to change the [Image Tone], you can adjust settings such as the color and contrast before shooting an image. Select from the following six modes for Image Tone: Bright, Natural, Portrait, Landscape, Vibrant and Monochrome. The default se ...

  • Pentax 1938507 - page 157

    155 Shooting Settings 6 2 Press the 4 button. The Custom Image screen appears. After the power is turned on, the last image taken is displayed in the background. Set the main switch to | to change the background image to the Digital Preview image. 3 Use the four-way controller ( 45 ) to choose the Image Tone. 4 Use the four-way controller ( 23 ) to ...

  • Pentax 1938507 - page 158

    156 Shooting Settings 6 Setting the File Format You can select the number of recorded pixels from X , J , P and i . The more pixels there are, the larger the picture and the bigger the file size. The file size will also differ according to the [JPEG Quality] setting. The default setting is X 4672×3104. The paper sizes above are references for opti ...

  • Pentax 1938507 - page 159

    157 Shooting Settings 6 You can set the image quality level. The file size will also differ according to the [JPEG Rec. Pixels] setting. The default setting is C (Best). You can set the JPEG quality level in [JPEG Quality] in the [ A Rec. Mode] menu. (p.72) When the quality level is changed, the number of recordable images at that quality level app ...

  • Pentax 1938507 - page 160

    158 Shooting Settings 6 You can set the format of image files. The default setting is JPEG. Set [File Format] in the [ A Rec. Mode] menu. (p.72) When the file format is changed, the number of recordable images appears at the top right of the screen. You can select PEF or DNG format in [RAW file format] in the [ A Rec. Mode] menu when images are cap ...

  • Pentax 1938507 - page 161

    159 Shooting Settings 6 You can set the function when the | button (p.19) is pressed. The following settings are available. 1 Select [ | Button] in the [ A Rec. Mode] menu. 2 Press the four-way controller ( 5 ). 3 Use the four-way controller ( 45 ) to select O (On) or P (Off) for [Cancel each time]. When set to O (On), the recording format each tim ...

  • Pentax 1938507 - page 162

    160 Shooting Settings 6 White balance is a function for adjusting the color of an image so that white objects appear white. Set the white balance if you are not satisfied with the color balance of pictures taken with white balance set to F (Auto), or to intentionally apply a creative effect to your images. The default setting is F (Auto). * The col ...

  • Pentax 1938507 - page 163

    161 Shooting Settings 6 2 Press the four-way controller ( 4 ). The White Balance screen appears. 3 Press the four-way controller ( 23 ) and set. Set the main switch to | to display Digital Preview with the set White Balance. Fine-tuning White Balance is easier with Digital Preview. Press the { button to save the background Digital Preview image. 4 ...

  • Pentax 1938507 - page 164

    162 Shooting Settings 6 The u allows you to fine tune the White Balance setting. 1 Perform desired settings in Steps 1 to 3 of “Setting the White Balance”. 2 Press the four-way controller ( 5 ). The White Balance fine tune screen appears. 3 Use the four-way controller ( 2345 ) to fine tune White Balance. Seven levels and 225 patterns are availa ...

  • Pentax 1938507 - page 165

    163 Shooting Settings 6 You can adjust the white balance depending on the light source when taking pictures. With Manual White Balance, the camera can store delicate shades that cannot be precisely adjusted with the white balance preset values provided in the camera (p.160). This provides the optimum white balance for your surroundings. 1 Press the ...

  • Pentax 1938507 - page 166

    164 Shooting Settings 6 6 Press the shutter release button fully. Slide the focus mode lever to when the shutter cannot be released. The screen to select the measuring range is displayed. 7 Use the rear e-dial to select the entire screen or spot area for the measuring range. 8 When a spot area is selected, use the four-way controller ( 2345 ) to ...

  • Pentax 1938507 - page 167

    165 Shooting Settings 6 Use figures to set the color temperature. 1 Press the { button. The Fn menu appears. 2 Press the four-way controller ( 4 ). The White Balance screen appears. 3 Use the four-way controller ( 3 ) to select Color Temperature (the default setting is 5000K). 4 Press the four-way controller ( 5 ). 5 Use the four-way controller ( 2 ...

  • Pentax 1938507 - page 168

    166 Shooting Settings 6 7 Adjust the Color Temperature with the front and rear e-dial. Color Temperature steps differ depending on the e-dial. * The default setting for Color Temperature step units is Kelv in. You can change the step units to Mired in [19. Color temp. steps] in the [ A Custom Setting] menu. However, figures are converted to Kelvin ...

  • Pentax 1938507 - page 169

    167 Shooting Settings 6 You can set the color space to use. The default setting is [sRGB]. Set [Color Space] in the [ A Rec. Mode] menu. (p.72) Setting the Color Space 1s R G B Sets to sRGB color space. 2 AdobeRGB Sets to AdobeRGB color space. File names differ depending on the color space setting as shown below. For sRGB : IMGPxxxx.JPG For AdobeRG ...

  • Pentax 1938507 - page 170

    Memo 168 ...

  • Pentax 1938507 - page 171

    7 Playback Functions This chapter describes how to use the various playback functions in Playback mode. How to Operate the Menus During Playback ... 170 Rotating Images ................................................. 172 Enlarging Playback Images ............................... 173 Displaying Multiple Images ............................... 175 Di ...

  • Pentax 1938507 - page 172

    170 Playback Functions 7 How to Operate the Menus During Playback Press the 3 button in Playback mode. The [ Q Playback] menu appears. Perform settings related to playback and editing images in the [ Q Playback] menu. Set custom functions to fully use the functions of a SLR camera with the Custom Function Menu. The default setting does not change C ...

  • Pentax 1938507 - page 173

    171 Playback Functions 7 Press the { button during playback. The Fn menu appears. Press the four-way controller ( 2345 ) or the 4 button to set the operation. Playback Fn Menu Setting Items Key or Button Item Function Page 2 DPOF Settings Sets the DPOF settings. p.204 4 Digital Filter Changes the color tone of captured images, adds softening and sl ...

  • Pentax 1938507 - page 174

    172 Playback Functions 7 Rotating Images The u features a function that uses a sensor to rotate and correct the direction of the image when an image is captured with the side of the shutter release button facing up and the Mode dial facing down. You can also rotate the captured image 90° counterclockwise at a time with the steps below. 1 Press the ...

  • Pentax 1938507 - page 175

    173 Playback Functions 7 Enlarging Playback Images Images can be magnified up to 32 times in playback mode. 1 Press the Q button and use the four-way controller ( 45 ) to select an image. 100-0046 100-0046 100-0046 1/2000 1/2000 F5.6 F5.6 1/2000 F5.6 ...

  • Pentax 1938507 - page 176

    174 Playback Functions 7 2 Turn the rear e-dial to the right (toward y ). Image enlarges at each calibration (1.2 times* to 32 times). Operations available during Enlarged view * The default setting for the first click (minimum magnification) on the rear e-dial (toward right) is 1.2 times. You can change this in [Playback display] in [ Q Playback] ...

  • Pentax 1938507 - page 177

    175 Playback Functions 7 Displaying Multiple Images You can display 4, 9 or 16 images on the monitor at the same time. The default setting is 9-image display. The number of images can be changed but 9-image display is explained here. 1 Press the Q button. 2 Turn the rear e-dial to the left (toward f ). The multi-image display screen appears. Up to ...

  • Pentax 1938507 - page 178

    176 Playback Functions 7 3 Turn the rear e-dial to the right (towards y ) or press the 4 button. A full screen display of the selected image appears. 1 In the multi-image display screen, press the { button. The multi-image options screen appears. 2 Use the four-way controller ( 425 ) to select the number of images to display at once. The camera ret ...

  • Pentax 1938507 - page 179

    177 Playback Functions 7 Displaying a Folder You can display the contents of folders in the multi-image display screen. 1 Turn the rear e-dial to the left in the multi-image display screen. 2 Use the four-way controller ( 2345 ) to select the folder you want to display and press the 4 button. The images in the folder are displayed according to the ...

  • Pentax 1938507 - page 180

    178 Playback Functions 7 Comparing Images You can display two images side-by-side. 1 Press the { button in Playback mode, and then press the 4 button. Two images are displayed side-by-side. The same image is displayed on the left and right. Turn the front e-dial to select the images to compare. You can also press the { button in Enlarged view to di ...

  • Pentax 1938507 - page 181

    179 Playback Functions 7 Slideshow You can play back all images recorded on your SD Memory Card successively. To start continuous playback, use the menu screen displayed on the monitor. 1 Press the Q button and use the four-way controller ( 45 ) to select an image to be displayed first. 2 Press the { button. The Fn menu appears. OK Fn Exit Exit Exi ...

  • Pentax 1938507 - page 182

    180 Playback Functions 7 3 Press the four-way controller ( 5 ). Start screen is displayed and slideshow begins. Operations available during a slideshow Operations available when paused 4 Stop the slideshow. Slideshow ends when one of the following is performed during playback or when paused. • Four-way controller ( 3 ) is pressed *1 • Q button ...

  • Pentax 1938507 - page 183

    181 Playback Functions 7 Set image display interval for slideshow to [3 sec], [5 sec], [10 sec] or [30 sec]. The default setting is [3 sec]. Set whether or not to play back repeatedly. The default setting is [Off]. 1 Select [Slideshow] in the [ Q Playback] menu. 2 Press the four-way controller ( 5 ). 3 Press the four-way controller ( 5 ) and use th ...

  • Pentax 1938507 - page 184

    182 Playback Functions 7 Changing Playback Display Method The camera switches display information when you press the M button in the Playback screen. A histogram shows the brightness distribution of an image. The horizontal axis represents brightness (dark at the left and bright at the right) and the vertical axis represents the number of pixels. T ...

  • Pentax 1938507 - page 185

    183 Playback Functions 7 Understanding Brightness If the brightness is correct, the graph peaks in the middle. If the image is too dark, the peak is on the left side, and if it is too bright, the peak is on the right side. When the image is too dark, the part to the left is cut off (dark portions with no detail) and when the image is too bright, th ...

  • Pentax 1938507 - page 186

    184 Playback Functions 7 You can set whether or not to display the Bright/Dark area warning in Playback mode and set the initial magnification when enlarging images. 1 Select [Playback display] in the [ Q Playback] menu. 2 Press the four-way controller ( 5 ). 3 Use the four-way controller ( 45 ) to select O (On) or P (Off). 4 Use the four-way contr ...

  • Pentax 1938507 - page 187

    185 Playback Functions 7 Deleting Multiple Images You can delete all saved images at once. 1 Press the Q button. 2 Press the i button twice. The Delete All screen appears. 3 Use the four-way controller ( 23 ) to select [Delete All]. Deleting All Images Deleted images cannot be restored. A confirmation screen appears when there are protected images. ...

  • Pentax 1938507 - page 188

    186 Playback Functions 7 4 Press the 4 button. All images are deleted. A confirmation screen appears when there are protected images. Press the four-way controller ( 23 ) to select [Delete All] or [Leave All] and press the 4 button. You can delete multiple images from the multi-image display at once. 1 Press the Q button. 2 Turn the rear e-dial to ...

  • Pentax 1938507 - page 189

    187 Playback Functions 7 3 Press the i button. 9 appears on the images. 4 Use the four-way controller ( 2345 ) to move to the images to delete and press the 4 button. Image is selected and O appears. Protected images cannot be selected. 5 Press the i button. The Delete confirmation screen appears. 6 Use the four-way controller ( 23 ) to select [Sel ...

  • Pentax 1938507 - page 190

    188 Playback Functions 7 You can delete all images in a selected folder. 1 Turn the rear e-dial to the left (toward f ) in Playback mode to display the folders. 2 Press the four-way controller ( 2345 ) to select the folder to delete and press the i button. The Delete Folder confirmation screen appears. 3 Use the four-way controller ( 2 ) to select ...

  • Pentax 1938507 - page 191

    189 Playback Functions 7 Protecting Images from Deletion (Protect) You can protect images from being accidentally deleted. 1 Press the Q button and use the four-way controller ( 45 ) to select an image. 2 Press the Z button. The Protect screen appears. 3 Use the four-way controller ( 23 ) to select [Protect]. 4 Press the 4 button. The selected imag ...

  • Pentax 1938507 - page 192

    190 Playback Functions 7 1 Press the Q button. 2 Press the Z button twice. The Protect all images screen appears. 3 Press the four-way controller ( 23 ) to select [Protect] and press the 4 button. All images saved in the SD Memory Card are protected. Protecting All Images Select [Unprotect] in Step 3 to cancel the Protect setting on all of the imag ...

  • Pentax 1938507 - page 193

    191 Playback Functions 7 Connecting the Camera to AV Equipment By using the provided video cable (I-VC28), you can play back images using a TV or other device with a video IN jack as your monitor. Make sure that both the TV and the camera are turned off before connecting the cable. 1 Selecting the Video Output Format (p.233) 1 Open the terminal cov ...

  • Pentax 1938507 - page 194

    Memo 192 ...

  • Pentax 1938507 - page 195

    8 Processing Images This chapter describes how to process pictures taken and edit RAW images. Processing Images with Digital Filters ............. 194 Editing RAW Images .......................................... 197 ...

  • Pentax 1938507 - page 196

    194 Processing Images 8 Processing Images with Digital Filters You can edit shot images using digital filters. Processed images are saved under a different name. 1 Press the { button in Playback mode. The Fn menu appears. 2 Press the four-way controller ( 4 ). The screen for selecting the filter appears. TIFF and RAW images cannot be processed usin ...

  • Pentax 1938507 - page 197

    195 Processing Images 8 3 Use the four-way controller ( 45 ) to select an image. 4 Use the four-way controller ( 23 ) to select a filter. Select a filter and preview the effects on the image. 5 Adjust with the front e-dial and rear e-dial. Filter name Function Front e-dial Rear e-dial B&W Converts to a black and white image. Changes the contras ...

  • Pentax 1938507 - page 198

    196 Processing Images 8 When another image is selected with the four-way controller ( 45 ), the image appears in the set filter. 6 Press the 4 button. The save confirmation screen appears. 7 Use the four-way controller ( 23 ) to select [Save as]. Press the 3 button to return to the previous screen. Select [Cancel] and press the 4 button to return t ...

  • Pentax 1938507 - page 199

    197 Processing Images 8 Editing RAW Images You can convert captured RAW files into JPEG or TIFF files. 1 Press the { button in Playback mode. The Fn menu appears. 2 Press the four-way controller ( 3 ). 3 Press the 4 button. The parameters recorded in the image file appear. To specify the parameters, see “Specifying the Parameters” (p.200). Edit ...

  • Pentax 1938507 - page 200

    198 Processing Images 8 4 Press the 4 button. The save confirmation screen appears. 5 Use the four-way controller ( 23 ) to select [Save as]. Press the 3 button to return to the previous screen. Select [Cancel] and press the 4 button to return to single-image playback mode. 6 Press the 4 button. The edited image is saved under a different name. Sel ...

  • Pentax 1938507 - page 201

    199 Processing Images 8 4 Press the four-way controller ( 2345 ) to select the RAW image to edit and press the 4 button to select the check box ( O ). Press the 4 button again to clear the check box ( P ). Turn the rear e-dial toward f to select single-image display and view the image. You can select up to 100 images at a time. 5 Press the { button ...

  • Pentax 1938507 - page 202

    200 Processing Images 8 Specifies the parameters for editing RAW images. When multiple images are selected, all images are edited with the same parameters. If Quality Level is not set to [TIFF], images are saved as JPEG images. 1 Select [Change Setting] in Step 3 of p.197 or Step 5 of p.199 and press the 4 button. The parameter setting screen appea ...

  • Pentax 1938507 - page 203

    201 Processing Images 8 3 Use the four-way controller ( 45 ) to change the parameter. Use the four-way controller ( 5 ) to display the setting screen for White Balance/Custom Image. To make these settings, see “Adjusting the White Balance” (p.160) and “Setting the Image Processing Method in Capture Mode (Custom Image)” (p.154). 4 Press the ...

  • Pentax 1938507 - page 204

    Memo 202 ...

  • Pentax 1938507 - page 205

    9 Printing from the Camera This chapter describes how to make the printing settings. Setting the Printing Service (DPOF) ................. 204 Printing Using PictBridge .................................. 207 ...

  • Pentax 1938507 - page 206

    204 Printing from the Camera 9 Setting the Printing Service (DPOF) You can order conventional photograph prints by taking the SD Memory Card with recorded images to a store for a printing service. DPOF (Digital Print Order Format) settings allow you to specify the number of copies or to imprint the date. Set the following items for each image. 1 Pr ...

  • Pentax 1938507 - page 207

    205 Printing from the Camera 9 4 Use the four-way controller ( 45 ) to choose the number of copies and press the four-way controller ( 3 ). The frame moves to [Date]. 5 Use the four-way controller ( 45 ) to choose whether to insert the date ( O ) or not ( P ). O : The date will be printed. P : The date will not be printed. You can select the next o ...

  • Pentax 1938507 - page 208

    206 Printing from the Camera 9 2 Press the four-way controller ( 2 ). The DPOF screen appears. 3 Press the { button. The screen for making DPOF settings for all images appears. 4 Use the four-way controller ( 45 ) to choose the number of copies and whether to insert the date ( O ) or not ( P ). Refer to Steps 4 and 5 of “Printing Single Images” ...

  • Pentax 1938507 - page 209

    207 Printing from the Camera 9 Printing Using PictBridge This function lets you print images directly from the camera without using a PC (direct printing). Connect the camera and PictBridge compatible printer with the included USB cable (I-USB17) to print directly. Select the images you want to print, the number of copies and whether to insert the ...

  • Pentax 1938507 - page 210

    208 Printing from the Camera 9 1 Press the 3 button. 2 Use the four-way controller ( 45 ) to select the [ R Set-up] menu. 3 Use the four-way controller ( 23 ) to select [USB Connection]. 4 Press the four-way controller ( 5 ). A pop-up menu appears. 5 Use the four-way controller ( 23 ) to select [PictBridge]. 6 Press the 4 button. The setting is cha ...

  • Pentax 1938507 - page 211

    209 Printing from the Camera 9 1 Turn off the camera. 2 Face the arrow on the provided USB cable toward the S mark on the camera, and connect the camera and PictBridge compatible printer. The PictBridge logo is displayed on PictBridge compatible printers. 3 Turn the printer on. 4 After printer start-up is complete, turn the camera on. The PictBridg ...

  • Pentax 1938507 - page 212

    210 Printing from the Camera 9 1 Use the four-way controller ( 23 ) to select [Single Image] on the PictBridge menu. 2 Press the 4 button. The Print single image screen appears. 3 Use the four-way controller ( 45 ) to choose an image to print. 4 Use the four-way controller ( 23 ) to choose the number of copies. You can print up to 99 copies. 5 Use ...

  • Pentax 1938507 - page 213

    211 Printing from the Camera 9 7 Press the { button. The screen for changing print settings appears. 8 Select [Paper Size] and press the four-way controller ( 5 ). The Paper Size screen appears. 9 Use the four-way controller ( 2345 ) to choose the paper size. You can only choose a size that is supported by your printer. When [ _ Setting] is selecte ...

  • Pentax 1938507 - page 214

    212 Printing from the Camera 9 1 Use the four-way controller ( 23 ) to select [All Images] on the PictBridge menu. 2 Press the 4 button. The Print all images screen appears. 3 Choose the number of copies and whether to imprint the date or not. The number of copies and the date setting that you choose apply to all of the images. Refer to Steps 4 and ...

  • Pentax 1938507 - page 215

    213 Printing from the Camera 9 1 Use the four-way controller ( 23 ) to select [DPOF AUTOPRINT] on the PictBridge menu. 2 Press the 4 button. The Print w/DPOF settings screen appears. Use the four-way controller ( 45 ) to check the number of copies for each image, whether the date is imprinted or not, and total number of copies. The number of copies ...

  • Pentax 1938507 - page 216

    Memo 214 ...

  • Pentax 1938507 - page 217

    10 Camera Settings This chapter describes how to change the camera settings. How to Operate the [ R Set-up] Menu ............... 216 Formatting the SD Memory Card ...................... 218 Setting the Beep Setting, Date and Time, and Display Language ............................................... 219 Adjusting the Monitor and the Menu Display ... ...

  • Pentax 1938507 - page 218

    216 Camera Settings 10 How to Operate the [ R Set-up] Menu Press the 3 button and use the four-way controller ( 45 ) to display the [ R Set-up] menu. Perform various settings related to the camera in the [ R Set-up] menu. [ R Set-up] Menu Setting Items Item Function Page USER Registers the current camera settings to USER. p.133 Format Formats the S ...

  • Pentax 1938507 - page 219

    217 Camera Settings 10 *1 Refer to p.11 of the “PENTAX PHOTO Browser 3/PENTAX PHOTO Laboratory 3 Operating Manual” for details on connecting the camera to a PC. *2 In USER mode, this is displayed instead of Reset. Sensor Cleaning Locks the mirror in the up position for cleaning the CMOS sensor. p.254 Reset Resets all settings. p.238 Reset USER ...

  • Pentax 1938507 - page 220

    218 Camera Settings 10 Formatting the SD Memory Card Use this camera to format (initialize) an SD Memory Card that is unused or has been used on other cameras or digital devices. Formatting will delete all the data on the SD Memory Card. 1 Select [Format] in the [ R Set-up] menu. 2 Use the four-way controller ( 5 ) to display the Format screen. 3 U ...

  • Pentax 1938507 - page 221

    219 Camera Settings 10 Setting the Beep Setting, Date and Time, and Display Language You can turn the camera operation beep on or off. The default setting is all O (On). There are five items that you can set: In-focus, AE Lock, | button, Self- timer and Remote Control. 1 Select [Beep] in the [ R Set-up] menu. 2 Press the four-way controller ( 5 ). ...

  • Pentax 1938507 - page 222

    220 Camera Settings 10 You can change the initial date and time settings. You can also set the display style. Choose [mm/dd/yy], [dd/mm/yy] or [yy/mm/dd]. Choose [12h] (12 hour) or [24h] (24 hour) for time display method. Set in [Date Adjust] in the [ R Set-up] menu. (p.216) 1 Setting the Date and Time (p.48) Changing the Date and Time and the Disp ...

  • Pentax 1938507 - page 223

    221 Camera Settings 10 The date and time selected in “Initial Settings” (p.45) serve as the date and time of your present location. Setting [World Time] enables you to display the local date and time on the monitor when traveling overseas. 1 Select [World Time] in the [ R Set-up] menu. 2 Press the four-way controller ( 5 ). The World Time scree ...

  • Pentax 1938507 - page 224

    222 Camera Settings 10 7 Use the four-way controller ( 3 ) to select [DST]. 8 Use the four-way controller ( 45 ) to select O (On) or P (Off). Select O (On) if the Destination city uses daylight saving time (DST). 9 Press the 4 button. The World Time setting is saved. 10 Press the 3 button twice. The camera is ready to take a picture. • See “Lis ...

  • Pentax 1938507 - page 225

    223 Camera Settings 10 List of World Time Cities Region City Region City North America Honolulu Africa/ West Asia Dakar Anchorage Algiers Vancouver Johannesburg San Francisco Istanbul Los Angeles Cairo Calgary Jerusalem Denver Nairobi Chicago Jeddah Miami Tehran Toronto Dubai New York Karachi Halifax Kabul Central and South America Mexico City Male ...

  • Pentax 1938507 - page 226

    224 Camera Settings 10 You can change the language in which the menus, error messages, etc. are displayed. Set in [Language/ ] in the [ R Set-up] menu. (p.216) You can choose from 18 languages: English, French, German, Spanish, Portuguese, Italian, Dutch, Danish, Swedish, Finnish, Polish, Czech, Hungarian, Turkish, Russian, Korean, Chinese (Traditi ...

  • Pentax 1938507 - page 227

    225 Camera Settings 10 Adjusting the Monitor and the Menu Display You can set the size of the text selected in the menus to [Std.] (normal display) or [Large] (magnified display). Set in [Text Size] in the [ R Set-up] menu. (p.216) Set the length of time that the guides are displayed on the monitor when the camera is turned on or the exposure mode ...

  • Pentax 1938507 - page 228

    226 Camera Settings 10 You can adjust the brightness of the monitor. Adjust settings when the monitor is hard to see. Set in [Brightness Level] in the [ R Set-up] menu. (p.216) Adjusts the color of the monitor. 1 Select [LCD Color Tuning] in the [ R Set-up] menu. 2 Press the four-way controller ( 5 ). 3 Use the four-way controller ( 23 ) to adjust ...

  • Pentax 1938507 - page 229

    227 Camera Settings 10 5 Press the 3 button. The camera returns to the Capture or Playback mode. You can perform the settings related to Instant Review and Digital Preview. You can set the Instant Review display time and whether or not to display the histogram and Bright/Dark area warning. The default settings are [1 sec] for the display time and [ ...

  • Pentax 1938507 - page 230

    228 Camera Settings 10 4 Use the four-way controller ( 3 ) to select [Histogram]. 5 Use the four-way controller ( 45 ) to select O (On) or P (Off) for [Histogram]. 6 Use the four-way controller ( 3 ) to select [Bright/Dark area]. 7 Use the four-way controller ( 45 ) to select O (On) or P (Off). 8 Press the 3 button twice. The camera is ready to tak ...

  • Pentax 1938507 - page 231

    229 Camera Settings 10 You can set whether or not to display the histogram and Bright/Dark area warning during Digital Preview. The default setting is [Off] for the histogram and Bright/Dark area warning. 1 Select [Digital Preview] in the [ Q Playback] menu. 2 Press the four-way controller ( 5 ). The screen for setting the Digital Preview appears. ...

  • Pentax 1938507 - page 232

    230 Camera Settings 10 Setting the Image File Naming Convention You can select the method for assigning the folder names for storing images. The default setting is [Date]. Set in [Folder Name] in the [ R Set-up] menu. (p.216) You can select the method for assigning the file number of an image when saved to a new folder. Select O (On) or P (Off) for ...

  • Pentax 1938507 - page 233

    231 Camera Settings 10 You can change the file names of images. The default naming conventions for the color space (p.167) settings are as follows. [xxxx] indicates the file number. This is displayed as a four-digit sequential number. (p.230) For sRGB, you can change [IMGP] (4 characters) to the desired characters. For AdobeRGB, of the 4 characters ...

  • Pentax 1938507 - page 234

    232 Camera Settings 10 4 After entering the desired characters, press the { button. The text is changed. 5 Press the 3 button twice. The camera returns to the Capture or Playback mode. You can reset the file name to the default setting by selecting [Reset File Name]. (p.241) ...

  • Pentax 1938507 - page 235

    233 Camera Settings 10 Selecting the Video Output Format and Power Settings When you connect the camera to AV equipment such as a TV, choose the appropriate video output format (NTSC or PAL) for playing back images. Set in [Video Out] in the [ R Set-up] menu. (p.216) 1 Connecting the Camera to AV Equipment (p.191) You can set the camera to turn off ...

  • Pentax 1938507 - page 236

    234 Camera Settings 10 You can set the battery priority to the camera or the battery grip when a battery grip (p.256) is attached. The default setting is [Auto Select]. 1 Select [Select battery] in the [ R Set-up] menu. 2 Press the four-way controller ( 5 ). The screen for selecting the battery appears. 3 Press the four-way controller ( 5 ). Use th ...

  • Pentax 1938507 - page 237

    235 Camera Settings 10 Using Pixel Mapping Pixel mapping is a function for mapping out and correcting for defective pixels in the CMOS sensor. 1 Select [Pixel Mapping] in the [ R Set-up] menu. 2 Press the four-way controller ( 5 ). 3 Press the four-way controller ( 23 ) to select [Pixel Mapping] and press the 4 button. Defective pixels are mapped a ...

  • Pentax 1938507 - page 238

    236 Camera Settings 10 Selecting Capture Mode Settings to Save in the Camera You can select which settings to save when the camera is turned off. The following settings can be saved: Flash mode, Drive mode, White Balance, Sensitivity, EV Compensation, Flash Exp. Comp., Auto Bracket, Playback Display and File No. The default setting is all [On]. 1 S ...

  • Pentax 1938507 - page 239

    11 Resetting to Default Settings Resets the camera settings. Resetting Rec. Mode/Playback/Set-up Menu ... 238 Resetting the Custom Function Menu .............. 239 Resetting Other Settings ................................... 240 ...

  • Pentax 1938507 - page 240

    238 Resetting to Default Settings 11 Resetting Rec. Mode/Playback/Set- up Menu Settings in [ A Rec. Mode] menu, [ Q Playback] menu and [ R Set-up] menu can be reset to default settings. However, Date Adjust, Language/ , Video Out, Text Size and the World Time city setting are not reset. When the exposure mode is set to USER, [Reset USER setting] (p ...

  • Pentax 1938507 - page 241

    239 Resetting to Default Settings 11 Resetting the Custom Function Menu Reset settings in [ A Custom Setting] menu to default settings. Settings in [ A Rec. Mode] menu, [ Q Playback] menu and [ R Set-up] menu are not reset. 1 Select [Reset Custom Function] in the [ A Custom Setting] menu. 2 Use the four-way controller ( 5 ) to display the Reset Cus ...

  • Pentax 1938507 - page 242

    240 Resetting to Default Settings 11 Resetting Other Settings You can reset saved USER mode settings to their default settings. 1 Set the mode dial to A . 2 Select [Reset USER setting] in the [ R Set-up] menu. 3 Use the four-way controller ( 5 ) to display the Reset USER setting screen. 4 Use the four-way controller ( 23 ) to select [Reset]. 5 Pres ...

  • Pentax 1938507 - page 243

    241 Resetting to Default Settings 11 If you changed the file name setting (p.231), you can reset this to the default setting. 1 Select [File Name] in the [ R Set-up] menu and press the four-way controller ( 5 ). 2 Press the four-way controller ( 23 ) to select [Reset File Name] and press the four-way controller ( 5 ). 3 Press the four-way controlle ...

  • Pentax 1938507 - page 244

    Memo 242 ...

  • Pentax 1938507 - page 245

    12 Appendix Default Settings .................................................. 244 Functions Available with Various Lens Combinations ..................................................... 249 Notes on [36. Using Aperture Ring] .................. 251 Cleaning the CMOS Sensor ............................... 252 Optional Accessories ................. ...

  • Pentax 1938507 - page 246

    244 Appendix 12 Default Settings The table below lists the factory default settings. Table notations are as follows. The current setting (last memory) is saved when the camera is turned off. Reset Setting Yes : The setting returns to the default setting with the reset function (p.237). No : The setting is saved even after reset. [ A Rec. Mode] Menu ...

  • Pentax 1938507 - page 247

    245 Appendix 12 [ Q Playback] Menu [ R Set-up] Menu Item Default Setting Reset Setting Page Playback display Bright/Dark area P (Off) Yes p.184 Quick Zoom P (Off) Yes Instant Review Display Time 1 sec Yes p.227 Histogram P (Off) Yes Bright/Dark area P (Off) Yes Live View Show Grid P (Off) Yes p.228 AF Frame Display P (Off) Yes Digital Preview Histo ...

  • Pentax 1938507 - page 248

    246 Appendix 12 *1 Reset only for [Reset USER setting] displayed when Mode dial is set to A (USER). *2 Reset only for [Reset File Name] in the [File Name] menu. [ A Custom Setting] Menu LCD Color Tuning ±0 Yes p.226 Video Out According to default setting No p.233 USB Connection PC Yes p.208 Auto Power Off 1 min Yes p.233 Folder Name Date Yes p.230 ...

  • Pentax 1938507 - page 249

    247 Appendix 12 *1 The saved adjustment value is reset only for [Reset] in the [35. AF Adjustment] menu. *2 The [ A Custom Setting] menu settings are reset. 13. AF Button Function Enable AF Yes p.112 14. AF by Press Halfway On Yes – 15. Superimpose AF Area On Yes p.107 16. AF in remote control Off Yes p.74 17. Slow Shutter Speed NR Auto Yes p.80 ...

  • Pentax 1938507 - page 250

    248 Appendix 12 Fn Menu *1 Automatically discharged in Green Mode. *2 [Bright] when [Language/ ] is set to a language other than Japanese. *3 The filter color and frequency settings can be saved or reset. Item Default Setting Reset Setting Page Drive Mode 9 (Single frame shooting) Yes p.117, p.122, p.125 Flash Mode E (Flash On) *1 Yes p.60 White Ba ...

  • Pentax 1938507 - page 251

    249 Appendix 12 Functions Available with Various Lens Combinations Lenses that can be used with this camera Only DA and FA J lenses and D FA/FA/F/A lenses having an s position on the aperture ring can be used with this camera. Refer to Notes on [36. Using Aperture Ring] (p.251) for other lenses and D FA/FA/F/A lenses with aperture ring set to a pos ...

  • Pentax 1938507 - page 252

    250 Appendix 12 Lens names and mount names DA lenses with an ultrasonic motor and FA zoom lenses with power zoom use the K AF2 mount. FA prime lenses (non-zoom lenses), DA lenses without ultrasonic motors and D FA, FA J and F lenses use the K AF mount. See the lens manual for details. Lenses and accessories that cannot be used with this camera When ...

  • Pentax 1938507 - page 253

    251 Appendix 12 Notes on [36. Using Aperture Ring] Aperture Ring Use When [36. Using aperture ring] is set to [Permitted] in [ A Custom Setting] menu (p.75), the shutter can be released even if the aperture ring of the D FA, FA, F or A lens is not set to the s position or a lens without a s position is attached. However, the features will be restri ...

  • Pentax 1938507 - page 254

    252 Appendix 12 Cleaning the CMOS Sensor Shadows may appear in the image for white backgrounds and other shooting conditions if the CMOS sensor becomes dirty or dusty. This indicates that the CMOS sensor must be cleaned. The Dust Removal function shakes the CMOS sensor to remove dust that has collected. 1 Select [Dust Removal] in the [ R Set-up] me ...

  • Pentax 1938507 - page 255

    253 Appendix 12 1 Select [Dust Alert] in the [ R Set- up] menu. 2 Press the four-way controller ( 5 ). 3 Point the lens at a white wall or other uniform surface and press the shutter release button fully. After image processing is performed, the Dust Alert screen appears. 4 Press the 4 button. The image is saved and Dust Alert is exited. • The ex ...

  • Pentax 1938507 - page 256

    254 Appendix 12 Raise the mirror up and open the shutter to clean with a blower. Please contact PENTAX Service Center for professional cleaning because the CMOS sensor is a precision part. Cleaning services involve a fee. You can use the Imagesensor Cleaning Kit O-ICK1 (optional) when cleaning the CMOS. 1 Turn the camera off and remove the lens. 2 ...

  • Pentax 1938507 - page 257

    255 Appendix 12 4 Press the four-way controller ( 5 ). The Sensor Cleaning screen appears. 5 Use the four-way controller ( 23 ) to select [Mirror Up]. 6 Press the 4 button. The mirror is locked in the up position. If you used Dust Alert to detect dust on the sensor within the last 30 minutes, the Dust Alert image appears on the monitor. Clean the s ...

  • Pentax 1938507 - page 258

    256 Appendix 12 Optional Accessories A number of dedicated accessories are available for this camera. Please contact a PENTAX Service Center for details regarding accessories. Products marked with an asterisk (*) are the same as those supplied with the camera. The Battery Grip has features such as a shutter release button, front e- dial, rear e-dia ...

  • Pentax 1938507 - page 259

    257 Appendix 12 Auto Flash AF540FGZ Auto Flash AF360FGZ The AF540FGZ and AF360FGZ are P-TTL auto flash units with a maximum guide number of approximately 54 and approximately 36 (ISO 100/m), respectively. Their features include slave-sync flash, contrast- control-sync flash, auto flash, high-speed sync flash, wireless flash, slow- speed sync and tr ...

  • Pentax 1938507 - page 260

    258 Appendix 12 Off-camera Shoe Clip CL-10 When using the AF540FGZ or AF360FGZ as a wireless flash, this large clip is used for setting the external flash on a desk or table. Magnifier Eyecup O-ME53 This viewfinder accessory is for magnifying up to 1.18 times. When the eyecup is attached to the u with a viewfinder magnification of 0.95 times, the c ...

  • Pentax 1938507 - page 261

    259 Appendix 12 ME Viewfinder Cap (*) Eyecup F P (*) LF-80: AF Frame Matte (standard) LL-80: AF Divided Matte LI-80: AF Scale Matte Connect to the cable switch terminal and operate the camera shutter release button. The cord length is 0.5 m. Lets you shoot pictures from within 5 m of the front or back of the camera. Interchangeable Focusing Screen ...

  • Pentax 1938507 - page 262

    260 Appendix 12 Camera Case O-CC55 Camera Strap O-ST53 (*) Clean the optical parts such as the CMOS sensor and lens of this camera. Body Mount Cap K Hot Shoe Cover F K (*) USB Cable I-USB17 (*) Video Cable I-VC28 (*) Sync Socket 2P Cap (*) Camera Case/Strap Imagesensor Cleaning Kit O-ICK1 Others ...

  • Pentax 1938507 - page 263

    261 Appendix 12 Error Messages Error Message Description Memory card full The SD Memory Card is full and no more images can be saved. Insert a new SD Memory Card or delete unwanted images. (p.40, p.70) You may be able to save new images by converting to JPEG format or changing the JPEG record pixels or JPEG quality setting. (p.156, p.157) No image ...

  • Pentax 1938507 - page 264

    262 Appendix 12 Not enough battery remaining to activate Pixel Mapping Appears during pixel mapping if the battery level is insufficient. Replace the battery with a charged one or use an AC adaptor D-AC50 (optional). (p.39) Image folder cannot be created The maximum folder number (999) and file number (9999) are being used, and no more images can b ...

  • Pentax 1938507 - page 265

    263 Appendix 12 No ink in the printer Pri nte r h as run out of ink. Replace ink and print. Paper stuck in the printer Paper is jammed in the printer. Remove paper and print. Data error A data error has occurred during printing. Turn the power off This appears when exiting the PictBridge mode. Turn the main switch off. Error Message Description ...

  • Pentax 1938507 - page 266

    264 Appendix 12 Troubleshooting We recommend checking the following items before contacting a service center. Problem Cause Remedy The camera does not turn on The battery is not installed Check if a battery is installed. If not, install a charged battery. The battery power is low Replace with a charged battery or use the AC adapter D-AC50 (optional ...

  • Pentax 1938507 - page 267

    265 Appendix 12 In rare cases, the camera may not operate correctly due to static electricity. This can be remedied by taking the battery out and putting it back in again. When the mirror remains in the up position, take the battery out and put it back in again. Then, turn the power on. The mirror will retract. After the procedure is done, if the c ...

  • Pentax 1938507 - page 268

    266 Appendix 12 Main Specifications Number of Shots Type TTL autofocus, auto-exposure SLR digital-still camera with built-in retractable P-TTL flash Effective Pixels Approx. 14.6 megapixels Sensor Total pixels approx. 15.07 megapixels, CMOS with a primary color filter Recorded Pixels X (RAW: 4672×3104 pixels), X (JPEG: 4672×3104 pixels), J (3872? ...

  • Pentax 1938507 - page 269

    267 Appendix 12 JPEG Quality (Compression): Z (Premium) = 1/2.8, C (Best) = 1/4.5, D (Better) = 1/8, E (Good) = 1/16 Recorded Pixels File Format/ JPEG Quality Capacity 4GB 2GB 1GB 512MB 256MB 128MB i 1824×1216 Z Approx. 1828 Approx. 931 Approx. 461 Approx. 230 Approx. 116 Approx. 59 C Approx. 2943 Approx. 1499 Approx. 737 Approx. 368 Approx. 185 A ...

  • Pentax 1938507 - page 270

    268 Appendix 12 LCD Panel Display b is lit = Built-in flash ready, b is blinking = Flash should be used or incompatible lens is being used, 3 = Auto discharge, > = Redeye reduction, Q = Slow-speed sync, 9 =Single frame shooting, j = Continuous shooting, g = Self-timer, h = Remote control shooting, ? = Battery exhaustion warning, ] = Auto bracket ...

  • Pentax 1938507 - page 271

    269 Appendix 12 Built-in Flash P-TTL built-in flash with serial control, GN approx. 13 (ISO 100 • m), Angles of coverage: 18 mm lens angle of view, Flash synchronization speed range at 1/180 sec. and slower, Daylight-sync flash, Slow-speed-sync flash, ISO range = P- TTL: 100 to 6400 External Flash Sync Hot shoe with M -contact, which couples with ...

  • Pentax 1938507 - page 272

    270 Appendix 12 Glossary AdobeRGB Color space recommended by Adobe Systems, Inc. for commercial printing. Wider range of color reproduction than sRGB. Covers most of the color range so colors only available when printed are not lost when editing images on a computer. When image is opened by non-compatible software, the colors look lighter. AE Meter ...

  • Pentax 1938507 - page 273

    271 Appendix 12 CMOS Sensor Photography element which converts the light entering through the lens into electric signals that create the image. Color Space A defined range of colors from the spectrum which are used. In digital cameras, [sRGB] is defined as the standard by Exif. In this camera, [AdobeRGB] is also used because of the richer color exp ...

  • Pentax 1938507 - page 274

    272 Appendix 12 Dynamic Range (D-Range) Indicated with a value expressing the light level reproducible in an image. This is the same as the term “latitude” used with silver halide film. Generally, when the dynamic range is wide, it is difficult for bright and dark areas to occur in the image, and when the dynamic range is narrow, a sharp image ...

  • Pentax 1938507 - page 275

    273 Appendix 12 Mired Proportional scale of measurement that consistently shows color change per unit. Determined by multiplying the inverse of the color temperature by 1,000,000. ND (Neutral Density) Filter A filter with many saturation levels that adjusts the brightness without affecting the color tone of pictures. Noise Reduction Process to redu ...

  • Pentax 1938507 - page 276

    274 Appendix 12 sRGB (standard RGB) International standard of color space established by the IEC (International Electrotechnical Commission). This is defined from color space for PC monitors and is also used as the standard color space for Exif. Vignetting The picture edges are blackened when part of the light coming from the subject is blocked by ...

  • Pentax 1938507 - page 277

    275 12 Appendix Index Symbols [ A Custom Setting] Menu ...................... 73, 170, 246 i (Delete) button ............. 21, 70 m (EV Compensation) button ............................. 19, 100 ] (Exposure Bracket) button ............................. 19, 129 K (Flash pop-up) button ............................... 19, 60 B (Green mode) ........... ...

  • Pentax 1938507 - page 278

    276 12 Appendix [ A Custom Setting] Menu ...................... 73, 170, 246 D Date Adjust ............................. 48 Date change ......................... 220 Daylight (White Balance) ...... 160 Daylight-Sync Shooting .......... 64 Delete ............................. 70, 185 Delete All Images ................. 185 i (Delete) button ........ ...

  • Pentax 1938507 - page 279

    277 12 Appendix High-ISO Noise Reduction ..... 80 High-Speed Flash Sync Mode .................................... 145 Histogram ....................... 26, 182 Hue ....................................... 154 Hyper-manual Mode a .......... 93 Hyper-program Mode e ........ 84 I Illustration (Digital Filter) ...... 195 Image Comparison ............... ...

  • Pentax 1938507 - page 280

    278 12 Appendix Print Service ......................... 204 Print Single Image ................ 210 Printer connection ................ 209 Program Line .......................... 82 Program Mode e ................... 84 Protect .................................. 189 Z (Protect) button ....... 21, 189 P-TTL (Flash) ....................... 148 P-TTL ...

  • Pentax 1938507 - page 281

    279 12 Appendix V Video cable .......................... 191 Video Output Format ............ 233 Viewfinder ........................ 27, 52 Vignetting ............................. 274 W White Balance ...................... 160 Wireless Mode (Flash) ......... 145 World Time ........................... 221 X M (Flash X-sync Speed) mode ............ ...

  • Pentax 1938507 - page 282

    280 12 Appendix WARRANTY POLICY All PENTAX cameras purchased through authorized bona fide photographic distribution channels are guaranteed against defects of material or workmanship for a period of twelve months from date of purchase. Service will be rendered, and defective parts will be replaced without cost to you within that period, provided th ...

  • Pentax 1938507 - page 283

    281 12 Appendix required, please keep the receipt or bills covering the purchase of your equipment for at least a year. Before sending your equipment for servicing, please make sure that you are sending it to the manufacturer’s authorized representatives or their approved repair shops, unless you are sending it directly to the manufacturer. Alway ...

  • Pentax 1938507 - page 284

    282 12 Appendix For customers in USA STATEMENT OF FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes o ...

  • Pentax 1938507 - page 285

    Declaration of Conformity According to 47CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals We: PENTAX Imaging Company A Division of PENTAX of America, Inc. Located at: 600 12 Street, Suite 300 Golden, Colorado 80401 U.S.A. Phone: 303-799-8000 FAX: 303-790-1131 Declare under sole responsibility that the product identified herein com ...

  • Pentax 1938507 - page 286

    Information on disposal for users 1. In the European Union If your product is marked with this symbol, it means that used electrical/electronic products should not be mixed with general household waste. There exists a separate collection system for these products. Used electric/electronic equipment must be treated separately and in accordance with ...

Produzent Pentax Kategorie Digital Camera

Dokumente, die wir vom Produzenten des Geräts Pentax 1938507 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pentax
- Bedienungsanleitungen 1938507
- Produktkarten Pentax
- Informationsbroschüren
- oder Energieetiketten Pentax 1938507
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pentax 1938507.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pentax 1938507, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pentax 1938507. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pentax 1938507 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pentax 1938507, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pentax 1938507 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pentax 1938507 verständlich ist.

Eine gänzliche Bedienungsanleitung von Pentax sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pentax 1938507 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pentax 1938507 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pentax 1938507, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pentax 1938507 - die uns die ersten Schritte während der Nutzung von Pentax 1938507 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pentax 1938507 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pentax 1938507 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pentax 1938507?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pentax 1938507 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pentax 1938507 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)