-
Hitachi CP-S833W - page 1
This Liquid Crystal Projector can display various computer signals and NTSC/P AL/SECAM video signals . Outline (1) High brightness A highly efficient optical system with a UHP lamp ensures high brightness. (2) High resolution Three separate high-definition liquid crystal panels are used for the R, G and B signals. (3) Compact size , light weight f ...
-
Hitachi CP-S833W - page 2
As these colours may not correspond with the coloured makings identifying the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Yellow. The wire coloured Blue must be connected t ...
-
Hitachi CP-S833W - page 3
3 Bef ore use Examples of illustrated marks [ Before Use ] Illustrated marks Various illustrated marks are used in this product and instruction manual so the product is used correctly and safely, and also to protect you and others from danger and your property from being damaged. This shows that a person could be killed or injured if the wrong oper ...
-
Hitachi CP-S833W - page 4
W arning 4 If any abnormality occur s. · When there is an abnormal smell or smoke, if you use this unit as it is, this could cause a fire or electric shock, etc. When an abnormality is found, immediately turn off the power switch and pull out the power plug from the power outlet. Check that there is no smoke, etc., then contact your dealer to repa ...
-
Hitachi CP-S833W - page 5
· If the cord is damaged (core wire is exposed, disconnected, etc.), ask your dealer to replace it. It may cause a fire, electric shock, etc. · Check that no dirt adheres to the power plug and fully insert without any play. If dirt adheres or the connection is incomplete, it may cause a fire, electric shock, etc. · The outer shield of power cord ...
-
Hitachi CP-S833W - page 6
6 Do not place this unit where it gets hot. Be careful since if you place the unit outdoors, in a place exposed to direct sunlight or near a heating device, the cabinet and parts could be affected. Cleaning the lens. To clean the lens, use a generally- available lens cleaning tissue (used for cleaning lens of camera, glasses, etc.). Be careful not ...
-
Hitachi CP-S833W - page 7
7 Main unit Lens Speaker Speaker Remote control sensor · Use the remote control transmitter within the range of about 16 feet from the remote control sensor and within 30 ° to both the left and right. Cooling fan (exhaust) Names and functions of eac h par t Handle ON indicator This blinks in the standby mode and lights in the operation mode.(See ...
-
Hitachi CP-S833W - page 8
8 Names and functions of eac h par t (continued) RGB input terminal D-sub 15pin shrink terminal (1/2) VIDEO input terminal (on video-equipped models only) S-VIDEO input terminal Mini DIN 4pin connector (1/2) VIDEO input terminal RCA Jack (1/2) AUDIO L/R input terminal RCA Jack (1/2) AC IN socket Connect the provided power cord. MAIN POWER switch Ma ...
-
Hitachi CP-S833W - page 9
9 Remote contr ol transmitter Names and functions of eac h par t (continued) *1 POSITION ON icon When presses POSITION ON button, back light on and icon is displayed. While displaying the icon, you can operate POSITION. Icon is displaying in video mode, but can not operate POSITION. *2 When the back light of MENU ON or POSITION ON button on without ...
-
Hitachi CP-S833W - page 10
Slide the battery compartment cover in the direction of the arrow while pressing slightly down on it. 10 Caution Cautions on use of batteries · Do not use batteries not specified for this unit. Also do not use old and new batteries together. It may cause a fire, injury due to burst of battery or liquid leakage. · When inserting batteries, pay att ...
-
Hitachi CP-S833W - page 11
Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage. Be especially careful not to install it with ventilation holes blocked. 11 Determine pictur ...
-
Hitachi CP-S833W - page 12
12 7 Press the INPUT b utton or the INPUT SELECT (VIDEO or RGB) b utton to select the sour ce of the signal to be pr ojected on the screen. · The selected signal input is displayed at the bottom right of the screen for 3 seconds. P ower on all connected equipment. The method of connecting various equipment, see on the page 19 ~ 27. T urn the MAIN ...
-
Hitachi CP-S833W - page 13
13 Basic operations (contin ued) · To reduce temperature inside the projector (cooling down), fan will rotate for about 1 minute after the lamp is turned off. · Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged. Press the ST ANDBY/ON button, f or 1 second. · The ON indicator lights up orange and the lamp turns ...
-
Hitachi CP-S833W - page 14
14 Basic operations (contin ued) MA GNIFYING FUNCTION It is possible to display a partially magnified picture. This function can be used in combination with a FREEZE function. [T O CHANGE MA GNIFICA TION] 3 Press the MA GNIFY + b utton. · By doing so, the center of the picture can be magnified as one part, becoming double in size. 1 Press the MA G ...
-
Hitachi CP-S833W - page 15
15 Press the MENU ( ) b uttons or the MENU ON / OFF b utton. · On-screen menus are displayed on the screen. 1 Select the menu to be adjusted using the MENU ( ) b uttons or DISK P AD . · Menu displayed in green is selected. 2 Select the item to be adjusted using the MENU ( ) b uttons or DISK P AD . · Item displayed in green can be adjusted. When ...
-
Hitachi CP-S833W - page 16
16 RGB signal input VIDEO signal input The menu SET UP serves for the change of parameters influencing the picture and for the move picture position. Adjustments and functions (contin ued) · When start up screen is displayed ( " NO INPUT IS DETECTED " or " SYNC IS OUT OF RANGE " is displayed), SETUP menu items other than VOLUME ...
-
Hitachi CP-S833W - page 17
17 Adjustments and functions (continued) The menu INPUT serves for the selection of input source. The menu IMAGE serves of the picture inversion. SETUP INPUT IMAGE OPT. MESSAGE TURN ON TURN OFF SETUP INPUT IMAGE OPT. MIRROR BLANK REVEAL MESSAGE SETUP INPUT IMAGE OPT. BLANK WHITE BLUE BLACK SETUP INPUT IMAGE OPT. REVEAL FAST MEDIUM SLOW SETUP INPUT ...
-
Hitachi CP-S833W - page 18
18 The menu OPT. allows you to control communication function etc. Adjustments and functions (continued) SETUP INPUT IMAGE OPT. COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF START UP SETUP INPUT IMAGE OPT. 7N1 8N1 COM. BITS SETUP INPUT IMAGE OPT. 1200 2400 4800 9600 19200 COM. SPEED (bps) SETUP INPUT IMAGE OPT. LANGUAGE ENGLISH FRANÇAIS DEUTSCH ESP ...
-
Hitachi CP-S833W - page 19
19 1. Input / output signal Connection to the RGB signal terminal 2. Signal input / output terminal 51 10 6 15 11 D-sub 15pin shrink terminal (Female) 1. Input signal Connection to the video signal terminals 2. Signal input terminal Ground Luminance signal S VIDEO input (Mini DIN4 pin) Ground Chrominance signal Caution Video input signal terminals ...
-
Hitachi CP-S833W - page 20
20 3. Example of computer signal Connection to the RGB signal terminal(contin ued) Caution · Some input source may not be displayed properly because they are not compatible with the projector. · Some input source may not be displayed in full size as shown "Display Dots". Resolution H X V fH (kHz) fV (Hz) Standard Type Note 1 Note 2 Note ...
-
Hitachi CP-S833W - page 21
21 4. Initial set signals The following signals are initially set. The settings may be different depending on the computer type. In this case, adjust the settings referring to pages 15, 16. Connection to the RGB signal terminal(contin ued) Back porch(b) Back porch(b) DATA HSYNC DATA VSYNC Sync.(a) Front porch(d) Active(c) Sync.(a) Front porch(d) Ac ...
-
Hitachi CP-S833W - page 22
22 1. Contr ol signal terminal Connection to the contr ol signal terminal 2. Mouse em ulation 5 1 10 6 15 11 D-sub 15pin shrink terminal (Male) Caution Turn off the power of both the projector and computer before connecting. Connect the computer to the control terminal of the projector using an appropriate cable. Refer to the instruction manual of ...
-
Hitachi CP-S833W - page 23
23 Connection to the contr ol signal terminal (continued) PS/2 mouse ADB (Mac) mouse 2 1 4 3 6 5 2 1 4 3 6 5 8 7 10 9 12 11 14 13 15 CLK D ATA SEL0 RTS GND +5V D ATA GND +5V CLK 2 1 4 3 6 5 2 1 4 3 8 7 10 9 12 11 14 13 15 RTS GND +5V ADB GND +5V ( POWER ON ) D ATA 2 1 4 3 6 5 2 1 4 3 Projector Computer Mini Din 6pin Mini Din 4pin Projector Computer ...
-
Hitachi CP-S833W - page 24
24 Connection to the contr ol signal terminal (continued) 3. Comm unication (1) Connect the projector and computer using RS 232C cable. (2) Turn off the computer and after computer is setting up, turn on the projector. (3) Select the data speed (COM.SPEED) and the data format (COM.BITS) of the projector. (See page 18) (4) Start communication. 4. Co ...
-
Hitachi CP-S833W - page 25
25 Connection to the contr ol signal terminal (continued) Contr ol data table Caution If computer sends the undefined command code or data code, Projector can not guarantee operation. Command is consisted of 2 command bytes and following data bytes. 1-st byte indicates the kinds of commands and the length of command. '0xH' : Error-reply P ...
-
Hitachi CP-S833W - page 26
26 The procedure of getting the Projector status (1)Computer sends the command '20H'+'yyH' to Projector. (2)Projector reply the command '1xH'+'yyH'+data bytes. The procedure of setting the Projector status (1)Computer sends the command '3xH'+'yyH'+data bytes. (2)Projector changes it’s st ...
-
Hitachi CP-S833W - page 27
27 INPUT S-VIDEO VIDEO AUDIO L R 1 1 1 2 2 2 RGB IN AUDIO IN OUT RGB OUT CONTROL 1 2 12 Example of system setup Connecting v arious equipment. AC Inlet Computer(Desk type) Computer (Note type) VTR with S-VHS out (video model only) VTR, etc. (video model only) CRT Display Audio amplifying equipment Caution · Turn power off to all devices before con ...
-
Hitachi CP-S833W - page 28
28 Clean the air filter about every 100 hours or when " CHECK THE AIR FLO W " is displayed. Cleaning the air filter T urn the main power s witich off and disconnect the po wer plug fr om the po wer outlet. 1 Remo ve the air filter fr om the bottom. 2 Clean the air filter using a v acuum c leaner . · When air filter is very dirty, wash it ...
-
Hitachi CP-S833W - page 29
29 Lamp Light source lamp has a service life. The picture will become dark or color will be poor when the lamp is used for a long time. If usage of lamp is continued in such cases, it could cause a malfunction. Replace lamp with new one. As reference for replacement time, indicator will operate or message will be displayed when the power is turned ...
-
Hitachi CP-S833W - page 30
30 On-screen displa y The following messages are displayed on the screen. Messa g e table *1 This message are not displayed after 3 minutes. But this message are displayed when you turn on the power again. Install the lamp co ver and fix it using scre ws. · To prevent burn, install the lamp cover and secure it using the screws. · Do not turn on t ...
-
Hitachi CP-S833W - page 31
31 Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer. When y ou think something wr ong A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem. Messa g e table (contin ued) The ON indicator, LAMP indicator and TEMP indicator will lig ...
-
Hitachi CP-S833W - page 32
32 Specifications All dimensions shown in inches. · All specifications are subject to change without notice. Dimension diagram 12.6 9.4 4.8 2.9 0.6 (0.4) Product name Liquid crystal projector Model name CP-S833W/E Display system 3 sheets of liquid crystal panels, 3 primary color lights shutter system Liquid crystal panel 2.3cm (0.9 inchs) TFT acti ...
Haben Sie eine Frage bezüglich Hitachi CP-S833W?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Hitachi CP-S833W nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Hitachi CP-S833W hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.