Bedienungsanleitung Husqvarna K 3600 MKII

24 Seiten 1.6 mb
Download

Zur Seite of 24

Summary
  • Husqvarna K 3600 MKII - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h K 3600 MKII Oper ator ′ s manual Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine. ...

  • Husqvarna K 3600 MKII - page 2

    2 – English KEY T O SYMBOLS Ke y to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ed pro ...

  • Husqvarna K 3600 MKII - page 3

    English – 3 CONTENTS Contents KEY T O SYMBOLS K ey to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the power cutter? ............................... 4 SAFETY INSTR UCTIONS Steps bef ore using a new ...

  • Husqvarna K 3600 MKII - page 4

    4 – English WHA T IS WHA T? What is what on the power cutter? 1 Diamond blade 2 Blade guard/spra y guard 3 Hydraulic motor 4 Locking b utton for the drive wheel 5 Grease nipples 6 Control f or the guide rollers 7 F ront handle (adjustable) 8 W ater adjustment control 9 Switch 10 W ater connector 11 Couplings f or h ydraulic hoses 12 Rating plate ...

  • Husqvarna K 3600 MKII - page 5

    English – 5 SAFETY INSTR UCTIONS Steps before using a ne w power cutter . • This machine is a h ydraulically operated po wer cutter intended f or free-hand cutting. The machine should be connected to a h ydraulic unit with an oil flow of 35-42 litres/min and a maximum pressure of 150 bar . • Please read the operator’ s manual carefully . ? ...

  • Husqvarna K 3600 MKII - page 6

    6 – English SAFETY INSTR UCTIONS Switch loc k and ON/OFF valve for the water The s witch lock is designed to pre vent accidental operation of the s witch. The ON/OFF valve f or the water supply is also controlled with the s witch lock. When the s witch lock (A) is pressed in this opens the w ater valv e and releases the switch (B). As long as the ...

  • Husqvarna K 3600 MKII - page 7

    English – 7 SAFETY INSTR UCTIONS Checking the b lade guard Check that the guard is complete and without an y crac ks or def ormations. General safety precautions • A power cutter is designed to cut hard materials, such as masonr y . Obser ve the increased risk of kickbac k when cutting soft materials. See instructions under the heading How to a ...

  • Husqvarna K 3600 MKII - page 8

    8 – English SAFETY INSTR UCTIONS Cutting General • Star t cutting with the machine running at maximum speed. • Alwa ys hold the machine in a fir m grip with both hands. Hold it so that the thumbs and fingers grip round the handles. Cutting technique The technique described below is of a general character . Check the details of each b lade c ...

  • Husqvarna K 3600 MKII - page 9

    English – 9 SAFETY INSTR UCTIONS Large w ork Cuts e xceeding 1 m - secure a batten along the line to be cut. The batten acts as a guide. Use this guide to make a marking cut along the entire length of the cut, 50-70 mm (2-3 inches) in depth. Remov e the guides once the marking cut has been made. Small work First make a shallo w marking cut, max 5 ...

  • Husqvarna K 3600 MKII - page 10

    10 – English SAFETY INSTR UCTIONS • Be aler t to mov ement of the work piece or anything else that can occur , which could cause the cut to close and pinch the blade . Pull in Pull in occurs when the disc’ s lower section suddenly stops or when the cut closes. (T o av oid, see the heading ”Basic r ules” and ”Jamming/rotation”, here be ...

  • Husqvarna K 3600 MKII - page 11

    English – 11 SETTINGS AND ADJUSTMENTS Drive On account of the machine’ s unique design the dr iving power is not transf erred at the centre of the blade. The flanges on the two guide rollers run in the blade’ s groov es. Springs on the guide rollers press out the rollers, which in turn press the V - shaped edge on the inside diameter of the ...

  • Husqvarna K 3600 MKII - page 12

    12 – English SETTINGS AND ADJUSTMENTS • Loosen the knob to offload the springs. • Pull out the lock f or the front handle and move the handle to the ser vice position. • Remov e the three screws holding the suppor t roller guard using a 6 mm he x ke y and lift off the cover . • Fit the blade . CA UTION! The blade has a g roov e (A) on on ...

  • Husqvarna K 3600 MKII - page 13

    English – 13 SETTINGS AND ADJUSTMENTS CA UTION! The machine should be upright. If the machine lies on its side the weight of the b lade makes it difficult to make a correct adjustment. • Tighten the knobs fully and the machine is ready to use. Hydraulic hoses • Bef ore connecting the hoses: Ensure that the couplings are clean, both on the ma ...

  • Husqvarna K 3600 MKII - page 14

    14 – English ST ARTING AND ST OPPING Star ting and stopping Starting • Grip the front handle with the left hand. • Grip the rear handle with the r ight hand. When you g rip the rear handle this releases the s witch lock. Stopping The machine is stopped by releasing the s witch. ! W ARNING! Note the follo wing before starting: Make sure you ar ...

  • Husqvarna K 3600 MKII - page 15

    English – 15 MAINTENANCE Maintenance Dismantling the complete guide r oller • Remov e the suppor t roller cov er. • Lift off the blade . • Unscrew the knob . First tur n the knob a fe w turns until you f eel a resistance. The guide roller then f ollows the knob out and stops when it f eels a resistance. The guide roller is pressed into the ...

  • Husqvarna K 3600 MKII - page 16

    16 – English MAINTENANCE Drive wheel 1 Lock the axle using the loc king button. See the instructions under the heading What is what?. 2 Loosen the centre screw and remo v e the washer . 3 Y ou can now lift off the drive wheel. CA UTION! Replace the dr ive wheel when fitting a ne w blade. A worn dr ive wheel can result in the b lade slipping and ...

  • Husqvarna K 3600 MKII - page 17

    English – 17 MAINTENANCE Reconstructing the blade Couplings 1 W ater 2 W ater filter 3 Return 4 Pressure IMPOR T ANT! If the coupling is dir ty , the dir t can enter the oil and cause increased wear on the h ydraulic motor , h ydraulic pump , v alves , etc. It can also pre v ent the coupling from sealing correctly . Alwa ys clean the couplings b ...

  • Husqvarna K 3600 MKII - page 18

    18 – English MAINTENANCE Maintenance schedule CA UTION! The char t is based on daily use of the equipment. Blades conforming to EN13236 Husqvarna K3600 MKII only conf orms to 98/37/EC and EN13236 together with the blades listed below: Note: The blades are a vailab le in different hardnesses f or diff erent materials, this is stated with two digit ...

  • Husqvarna K 3600 MKII - page 19

    English – 19 TR OUBLE SHOO TING Mechanics Symptom Probab le cause The blade does not rotate . Roller knobs not tightened fully . The blade not fitted on guide rollers correctly . Rollers tensioned too much. P ossible f aulty hose connection to the h ydraulic system. P ossible f aulty hose connection to the drive source or other h ydraulic proble ...

  • Husqvarna K 3600 MKII - page 20

    20 – English TECHNICAL D A T A *W e recommend the use of environmentally appro v ed h ydraulic oil. **With high ambient temperatures use oil with a higher viscosity . Note 1: Noise emissions in the environment measured as sound power (L W A ) in conformity with EC directive 2000/14/EC . Note 2: Noise pressure lev el according to EN 792-7/A1. Repo ...

  • Husqvarna K 3600 MKII - page 21

    English – 21 TECHNICAL D A T A EC-declaration of conf ormity Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqvarna K 3600 dating from 2010 serial numbers and onwards (the y ear is clearly stated on the rating plate, f ollowed by the serial number), complies with the requ ...

  • Husqvarna K 3600 MKII - page 22

    ´®z+UBT¶6A¨ ´®z+UBT¶6A¨ ...

  • Husqvarna K 3600 MKII - page 23

    ...

  • Husqvarna K 3600 MKII - page 24

    ´®z+UBT¶6A¨ 2010-01-13 ´®z+UBT¶6A¨ 1153345-26 Original instructions ...

Produzent Husqvarna Kategorie Saw

Dokumente, die wir vom Produzenten des Geräts Husqvarna K 3600 MKII erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Husqvarna
- Bedienungsanleitungen K 3600 MKII
- Produktkarten Husqvarna
- Informationsbroschüren
- oder Energieetiketten Husqvarna K 3600 MKII
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Husqvarna K 3600 MKII.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Husqvarna K 3600 MKII, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Husqvarna K 3600 MKII. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Husqvarna K 3600 MKII ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Husqvarna K 3600 MKII, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Husqvarna K 3600 MKII hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Husqvarna K 3600 MKII verständlich ist.

Eine gänzliche Bedienungsanleitung von Husqvarna sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Husqvarna K 3600 MKII bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Husqvarna K 3600 MKII befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Husqvarna K 3600 MKII, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Husqvarna K 3600 MKII - die uns die ersten Schritte während der Nutzung von Husqvarna K 3600 MKII erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Husqvarna K 3600 MKII hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Husqvarna K 3600 MKII im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Husqvarna K 3600 MKII?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Husqvarna K 3600 MKII nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Husqvarna K 3600 MKII hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)