Deutsch dropdown-ico

Bedienungsanleitung Oki C3400

35 Seiten 0.61 mb
Download

Zur Seite of 35

Summary
  • Oki C3400 - page 1

    59387501.jpg ...

  • Oki C3400 - page 2

    Network User’s Guide for C3400n and C3530 MFP Copyright Information - 2 Copyright Information Copyright © 2008 by Oki Data Amer icas, Inc. All Rights Reserved Document Information Network User’s Guide C3400n and C3530 MFP P/N 59387501, Revision 2.1 July, 2008 Disclaimer Every effort has been made to ensure th at the information in this documen ...

  • Oki C3400 - page 3

    Network User’s Guide for C3400n and C3530 MFP Table of Contents - 3 Table of Contents Notes, cautions and warnings . . . . . . . . . . . . . . . . . . . . . . . 5 Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specification ...

  • Oki C3400 - page 4

    Network User’s Guide for C3400n and C3530 MFP Table of Contents - 4 Setting the Printer Discovery settings . . . . . . . . . . . . . . . . . . 26 Changing the password . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Enable/Disable the Printer Web Page . . . . . . . . . . . . . . . . . . . 27 Quitting the network card setup utility . . ...

  • Oki C3400 - page 5

    Network User’s Guide for C3400n and C3530 MFP Notes, cautions and warnings - 5 N OTES , CAUTIONS AND WARNINGS NOTE A note provides additional inform ation to supplement the main te xt. ONLY USE GENUINE OKI ORIGINAL CONSUMABLES TO ENSURE THE BEST QUALITY AND PERFORMANCE FROM YOUR HARDWARE . NON-OKI ORIGINAL PRODUCTS MAY DAMAGE YOUR PRINTER'S ...

  • Oki C3400 - page 6

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 6 N ETWORK C ONFIGURATION I NTRODUCTION This User’s Guide explains the functiona lity of your printer’s built in 100BASE- TX/10BASE-T network interface. This network interface supports IE EE802.2, IEEE802.3, Ethernet-II and SNAP, and can detect those frame types automatical ...

  • Oki C3400 - page 7

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 7 S PECIFICATION S ELF - DIAGNOSTIC TEST With the printer power switched on, press the TES T button located on the Network Interface Panel (at the rear of the printer) for more than three seconds and then release. The self-diagnostic test results and configuration settings are ...

  • Oki C3400 - page 8

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 8 C ONFIGURATION UTILITIES You can configure the network interface card (NIC) by using one of th e following methods: UTILITY FEATURES SYSTEM REQUIREMENTS Network Card Setup Configure the N etwork Interface Card (NIC) by launching or installing the Network Card Setup utility . ...

  • Oki C3400 - page 9

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 9 N ETWORK C ARD S ETUP UTILITY The Network Card Setup utility allows you to carry out the following: > Set IP address, Subnet Mask and Gatew ay for TCP/IP manually or by using DHCP . > Launch the Printer W eb Page. > Enable/disable the Printer Settings W eb Page. > ...

  • Oki C3400 - page 10

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 10 key . Y ou can find the IP Address on the Self-Diagnostic T est printout. The Printer W eb Page is displayed. NOTE: On the web page you can view printer stat us, job lists and links. You can also configure the IP Address, Subnet Mask and Gateway for the network card. However ...

  • Oki C3400 - page 11

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 11 Network General Network Settings TCP / IP SNMP View and adjust any network settings relating to y our printer . Job List Job Queue Allows you to manage pending jobs for your printe r . Security Protocol ON/OFF Menu Lock Pas s wo r d Configuration Change your password and app ...

  • Oki C3400 - page 12

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 12 U SING SNMP The printer and network card can be managed via a standard SNMP management station. The network ca rd supports SNMPv1, MIB-II and Oki D a t a P r i v a t e M I B . T o e n a b l e c o r r e c t m a n a g e m e n t f r o m a n S N M P m a n a g e m e n t station, ...

  • Oki C3400 - page 13

    Network User’s Guide for C3400n and C3530 MFP Network Configuration - 13 4. In the “Choose Setup Language” dialog, select the appropriate language and click OK . The Oki LPR utility is displayed. 5. Click Next . 6. Click Yes to accept the Software Licence Agreement. 7. V erify “Destination” Folder and “Spool” F olde r and click Next . ...

  • Oki C3400 - page 14

    Network User’s Guide for C3400n and C3530 MFP Windows - 14 W INDOWS O VERVIEW This chapter provides guidelines on how to print over the network from various Microsoft Windows platforms. There are numerous ways of printing from Windows and the exact set-up will vary depending upon your environment. There are also numerous versions of Windows, whic ...

  • Oki C3400 - page 15

    Network User’s Guide for C3400n and C3530 MFP Windows - 15 2. If not already configured, a suitable IP address, Subnet Mask and Gateway address should be configured . If necessary , refer to Microsoft On-line Help. 3. Restart the oper ating system. C ONFIGURING W INDOWS TO USE TCP/IP N ETWOR KING W INDOWS 98/M E 1. Select Start -> Settings -&g ...

  • Oki C3400 - page 16

    Network User’s Guide for C3400n and C3530 MFP Windows - 16 6. The Windows NT installation CD-ROM may be required. Follow the remaining dialog box prompts. W INDOWS 2000 1. Select Start -> Settings -> Network and Dial-up Connections. 2. Double-click the Local Area Connection icon. In the “Local Area Connection Status” dialog bo x, click ...

  • Oki C3400 - page 17

    Network User’s Guide for C3400n and C3530 MFP Windows - 17 L AUNCHING THE N ETWORK C ARD S ETUP UTILITY The following steps describe how to launch and install the Network Card Setup utility: 1. Ensure that the printer is switched on and connected to the network. 2. Insert the Software CD-ROM into the CD-ROM drive. The Setup Utility starts automat ...

  • Oki C3400 - page 18

    Network User’s Guide for C3400n and C3530 MFP Windows - 18 S TARTING THE N ETWORK C ARD S ETUP UTILITY Once installed, you can launch the Ne twork Card Setup utility by selecting Start -> Programs -> Okidata -> Network Card Setup. M ANUALLY CONFIGURING THE IP ADDRESS If there is no DHCP protocol to automatically assign IP addresses to de ...

  • Oki C3400 - page 19

    Network User’s Guide for C3400n and C3530 MFP Windows - 19 3. Click OK . The “ Admin Password R equired” dialog b ox appears. 4. Enter the admin password as requested and click OK . 5. The “Setup Completed” message is displayed. If you now try to view the Printer Web Page, an error message is displayed (containing instructions on how to e ...

  • Oki C3400 - page 20

    Network User’s Guide for C3400n and C3530 MFP Windows - 20 C ONFIGURING W INDOWS TO PRINT TO THE NETWORK PRINTER Once you have configured the Network Card Setup utility you must configure Windows to print to the network printer. W INDOWS 98/M E When printing using TCP/IP the Oki LPR utility use the following procedure: 1. When installing the driv ...

  • Oki C3400 - page 21

    Network User’s Guide for C3400n and C3530 MFP Windows - 21 If the LPR port is not available, insta ll the Microsoft TCP/IP Printing Service. Insert the printer driver for Windows NT4.0. 1. Select Start -> Settings -> Control P anel. 2. Double-click the Network icon. 3. In the “Network” dialog box, click the “Services” tab. 4. If “ ...

  • Oki C3400 - page 22

    Network User’s Guide for C3400n and C3530 MFP Windows - 22 6. Click Next . 7. The “ Add Standard TCP/IP Printer P ort Wizard” is displayed. Click Next . 8. Click Next . 9. Under “Name or address of server providing LPD”, enter the host na m e o r I P a dd r e ss o f yo u r pr i n te r , fo r ex a m p le , ‘ 19 2.168.1.31’ . If the abo ...

  • Oki C3400 - page 23

    Network User’s Guide for C3400n and C3530 MFP Windows - 23 W INDOWS XP NOTE: Windows XP requires administrator privileges. With Windows XP, there are four op tions for printing using TCP/IP: > Oki LPR > Standard TCP/IP P ort usi ng: •L P R • Port 9100 Oki LPR To install the Oki LPR port, see “Oki LPR” on page 20. Standard TCP/IP Por ...

  • Oki C3400 - page 24

    Network User’s Guide for C3400n and C3530 MFP Windows - 24 Port 9100 > Set “Protocol” to Ra w . > Ensure that the “Port Number” is 9100 and that “SNMP Status Enabled” is not selected. 10. Click OK . 11. Click Next. 12. Click Finish and follow the instructions on the screen to finish installing the printer . ...

  • Oki C3400 - page 25

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 25 M ACINTOSH O VERVIEW This guide is for administrators and it should be used in conjunction with the relevant Macintosh manual. Ensure that the latest Macintosh service packs are installed. S UPPORTED VERSIONS Macintosh operating systems OS 9 to OS X 10.4.6 are supported. P RINTING THE C ...

  • Oki C3400 - page 26

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 26 N ETWORK C ARD S ETUP UTILITY FOR M AC OS 9 You can use the Oki Network Card Setup Utility (Macintosh) to assign an IP address and configure the network interface card. For more background information on the Network Card Setup Utility, refer to the “Network Card Setup utility” on pa ...

  • Oki C3400 - page 27

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 27 3. Under “Printer Discovery Settings” enter the “IP Broadcast Settings” and click Add . 4. Ensure that “Search local subnets” is selected. 5. Y ou can modify the “Timeout Settings” for the search scope. If y ou want to restore the original settings at any time, click the ...

  • Oki C3400 - page 28

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 28 2. From the main menu, select Printer -> W eb P age Settings. 3. Select Enable or Disable and click Save . 4. Enter your password and click OK . The “Settings updated successfully” message is displayed. 5. Click OK . The printer automatically restarts. If you now try to view the ...

  • Oki C3400 - page 29

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 29 N ETWORK C ARD S ETUP UTILITY FOR M AC OS X The built in Network Interface Card is also supported in the Macintosh OS X environment. Run the installer on the driver CD to install the printer driver. You can use the Oki Network Card Setup Utility (Macintosh) to assign an IP address and c ...

  • Oki C3400 - page 30

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 30 1. In the “Network Card Setup” pa ne, click to select the printer . 2. From the main menu, click Options -> Preferences. 3. Under “Printer Discovery Settings” enter the “IP Broadcast Settings” and click Add . 4. Ensure that “Search local subnets” is selected. 5. Y ou ...

  • Oki C3400 - page 31

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 31 E NABLE /D ISABLE THE P RINTER W EB P AGE To enable/disable access to the Printer Web Page: 1. In the “Network Card Setup” pa ne, click to select the printer . 2. From the main menu, select Printer -> W eb P age Settings. 3. Select Enable or Disable and click Save . 4. Enter your ...

  • Oki C3400 - page 32

    Network User’s Guide for C3400n and C3530 MFP Macintosh - 32 C ONFIGURING THE NETWORK INTERFACE CARD You can configure the Network Interface Card, view your printer status and adjust printer settings through the Printer Web Page. To access the web page, ensure that your printer is connected to the network and type the printer IP address into a we ...

  • Oki C3400 - page 33

    Network User’s Guide for C3400n and C3530 MFP Troubleshooting - 33 T ROUBLESHOOTI NG The network addresses used in this manual are examples only. Network addresses used in your installation must be generated from your own network. S ELF - DIAGNOSTIC TEST P RINTER DOES NOT PRINT > Check that your printer is switched on. > Check the printer s ...

  • Oki C3400 - page 34

    Network User’s Guide for C3400n and C3530 MFP Troubleshooting - 34 C ANNOT PRINT WITH LPR Carry out the following procedures to verify the printer settings: > T urn the printer off for 15 seconds and then on again. > Check there is a response to the ping command. > Check the network cable is correctly connected. > Change the cable and ...

  • Oki C3400 - page 35

    Network User’s Guide for C3400n and C3530 MFP Index - 35 I NDEX Numerics 100BASE-TX 6 10BASE-T 6 E Ethernet 6 I IP Address 17 configuring 17 manual configuration 18 Network Card Setup Utility 17 N Network Card Setup 9 Mac OS 9 26 Mac OS X 29 Windows 17 Network interface 6 card (NIC) 8 Panel 6 Network Interface Card 8 Network Interface Card (NIC) ...

Produzent Oki Kategorie Printer

Dokumente, die wir vom Produzenten des Geräts Oki C3400 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Oki
- Bedienungsanleitungen C3400
- Produktkarten Oki
- Informationsbroschüren
- oder Energieetiketten Oki C3400
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Oki C3400.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Oki C3400, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Oki C3400. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Oki C3400 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Oki C3400, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Oki C3400 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Oki C3400 verständlich ist.

Eine gänzliche Bedienungsanleitung von Oki sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Oki C3400 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Oki C3400 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Oki C3400, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Oki C3400 - die uns die ersten Schritte während der Nutzung von Oki C3400 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Oki C3400 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Oki C3400 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Oki C3400?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Oki C3400 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Oki C3400 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)