Bedienungsanleitung GBC PF3200

18 Seiten 0.49 mb
Download

Zur Seite of 18

Summary
  • GBC PF3200 - page 1

    Operation Manual Per fect Binder Model No. PF3200 ® ...

  • GBC PF3200 - page 2

    2 • Do not attempt to service your PF-3200 yourself. Contact an authorized GBC service representative for any required repairs or major maintenance for your PF-3200 . • There are NO user-serviceable parts inside the machine. T o avoid potential personal injury and/or property or machine damage, DO NOT REMOVE THE MACHINE’S COVER . • Y ou may ...

  • GBC PF3200 - page 3

    3 (THE FOLLOWING NOTE APPLIES ONL Y TO THE UNITS RA TED 1 15V 60HZ.) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment ...

  • GBC PF3200 - page 4

    SAFETY INSTRUCTIONS CAUTION: PF-3200 has implemented secondary thermostat to prevent the glue tank temperature from going over 392°F (200°C). When it occurs, the power of PF-3200 will be automatically turned off. Y ou have to wait for the glue tank to cool down before you can restart the machine. If this problem occurs again, call your authorized ...

  • GBC PF3200 - page 5

    5 Model PF-3200 Perfect Binder Maximum Book Size 12.6" x 15.75" (320mm x 400mm) Minimum Book Size 3.15" x 1.97" (80mm x 50mm) Maximum Binding Thickness 1.6" (40mm) Glue W arm Up 25 minutes (varies depending upon glue type) Glue W arm Up in Stand-by Mode 5 minutes Cycle Speed 360 cycles per hour Production Speed Up to 200 bo ...

  • GBC PF3200 - page 6

    6 INST ALLA TION Note: Y ou must remove the three red shipping brackets before installing your PF-3200. The procedures for installation: Step 1: Remove the red shipping bracket located on the left side of the clamp station as shown. Then reinstall the screws in clamp station. Step 2: Remove two red shipping brackets that are located around the nipp ...

  • GBC PF3200 - page 7

    7 No. Symbol Function LED Display / Symbol Example 1 EMERGENCY 2 ST AND BY / LED 3 CLOSE 4 LED DISPLA Y 5 CLEAR 6 COUNTER 7 ST ART / LED 8 OPEN 9 FUNCTION / LED 10 NOTCH / LED Stops all the actions of the machine. Except when “HOT” shows on the LED display . T emporarily lowers the temperature of glue tank so it won’t burn the glue when the m ...

  • GBC PF3200 - page 8

    8 1. T urn ON the power switch of PF-3200 as shown. The heater of PF-3200 will automatically heat the glue to the preset working temperature and display the status of the heating processes. • The 4 leftmost spaces of LED: the status of heating process (COLD, W ARM, or HOT). • The 2 rightmost spaces of LED: the elapsed time of heating. 2. Start ...

  • GBC PF3200 - page 9

    9 After the “ST ARTUP” procedures, the PF-3200 will automatically set itself MANUAL operation and flashing “LOAD BOOK” display . Note that the “NOTCH” LED is ON. 1. A. Press the “OPEN” button and place the book block inside the clamps. Be sure to follow the label instructions on the clamp to load the book block to the RIGHT of the r ...

  • GBC PF3200 - page 10

    10 Note: If you accidentally remove or drop the cover sheet during the clamping station returning to the nipping station, the control panel will show “COVER?”. At this moment, you have to place the cover on the nipping station and press “ST ART” button to resume the process. 5. When the display indicates “PUSH OPEN”, press the “OPEN? ...

  • GBC PF3200 - page 11

    11 Note: All books done in this mode must be same thickness. 1. In the MANUAL mode, make one book. Centering the cover to the centered point and adjust the side guide accordingly . 2. Press “FUNCTION” button to switch to “AUTO” operation. The “AUTO” LED will be lit and display flashing “LOAD BOOK” as shown. Note: The “NOTCH” LED ...

  • GBC PF3200 - page 12

    12 Note: If you accidentally remove or drop the cover sheet during the clamping station return to the nipping station, the control panel will show “COVER?”. At this moment, you have to place the cover on the nipping station and press “ST ART” button to recover the process. Having completed one bound book, the clamp will automatically open a ...

  • GBC PF3200 - page 13

    13 “P AD” is one of the PF-3200 operations that apply to special binding applications such as binding without a cover sheet. 1. Press “FUNCTION” button to switch to “P AD” operation. The “P AD” LED will be lit and display flashing “LOAD P AD” as shown. Note: The “NOTCH” LED is normally OFF . But you can press “NOTCH” but ...

  • GBC PF3200 - page 14

    14 ST ANDBY MODE Press “ST ANDBY” button, the PF-3200 will temporarily lower the temperature of glue tank so it won’t burn the glue when the machine is not operated. The LED displays “STBY00” as shown below . Where “00” is the timer display for the duration of the standby period. Press “ST ANDBY” button again when the “ST ANDBY? ...

  • GBC PF3200 - page 15

    15 The glue level may require adjustment when the thickness of the book or pad varies. Use the following book spine illustrations for guidelines. • Increasing the holt-melt glue when • Decreasing hot-melt glue when • Adjusting the glue level: 1. Turn the glue adjustment lock knob counter clockwise to loosen. 2. Increase the amount of glue by ...

  • GBC PF3200 - page 16

    16 After you have finished using the binder for the day , follow the following steps: 1. Close the clamps while the LED display flashing “LOAD BOOK” or “LOAD P AD”. 2. Press “ST ART” and “CLEAR” keys simultaneously . The clamp station will automatically move to the left of the machine and LED display “NP SVC”. 3. Clean the resid ...

  • GBC PF3200 - page 17

    17 T o enter the timer setup menu, you will need to press and hold down both the “OPEN” and “CLOSE” buttons, then turn the power on. Y ou should see “SET TR” in the LED DISPLA Y . Press the “FUNCTION” button to sequentially display TR1, TR2, TR3, TR4, TR5, TR6, “SA VE”, “CANCEL”, and “RESET”. Once you have selected the s ...

  • GBC PF3200 - page 18

    ® General Binding Corporation Northbrook, IL 60062-4195 http://www .GBC.com Printed in the U.S.A. Rev . A1 GBC Part # 7301322 ...

Produzent GBC Kategorie Binding Machine

Dokumente, die wir vom Produzenten des Geräts GBC PF3200 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen GBC
- Bedienungsanleitungen PF3200
- Produktkarten GBC
- Informationsbroschüren
- oder Energieetiketten GBC PF3200
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung GBC PF3200.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen GBC PF3200, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen GBC PF3200. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts GBC PF3200 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts GBC PF3200, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von GBC PF3200 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von GBC PF3200 verständlich ist.

Eine gänzliche Bedienungsanleitung von GBC sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von GBC PF3200 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von GBC PF3200 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich GBC PF3200, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts GBC PF3200 - die uns die ersten Schritte während der Nutzung von GBC PF3200 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit GBC PF3200 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von GBC PF3200 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich GBC PF3200?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit GBC PF3200 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit GBC PF3200 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)