-
AT&T 9341 - page 1
900 MHz Cor dless T elephone with Caller ID/Call W aiting 9341 Please also read Part 1 — Important Product Infor mation USER ’ S MANU AL Pa r t 2 A T&T and the globe symbol are registered trademar ks of A T&T Corp. licensed to Adv anced American T elephones. REVISED 6/14/00 9341_book_1ATT 6/14/00 4:07 PM Page ii ...
-
AT&T 9341 - page 2
© 2000 Advanced Amer ican T elephones. All rights reser ved. Printed in China. XXXXXXXX Issue 1A T&T 5/00 9341_book_1ATT 6/14/00 4:07 PM Page iii ...
-
AT&T 9341 - page 3
CONTENTS 1 BEFORE Y OU BEGIN . . . . . . . . . . . . . . . 3 About Caller Identification ............3 INST ALLA TION . . . . . . . . . . . . . . . . . . . . . . . 4 Befor e Y ou Install ...........................4 T able/Desk Installation...................5 W all Installation..............................6 FEA TURE SETTINGS . . . . . . . . . . . ...
-
AT&T 9341 - page 4
9341_book_1ATT 6/14/00 4:07 PM Page 2 ...
-
AT&T 9341 - page 5
BEFORE Y OU BEGIN 3 About Caller Identification (Caller ID) This product has a Caller ID with Call W aiting featur e that works with ser vice from your local phone service provider . Caller ID with Call W aiting lets you see who’ s calling before y ou answer the phone, even when y ou’ re on another call. Y ou may need to c hange your phone serv ...
-
AT&T 9341 - page 6
INST ALLA TION 4 Befor e Y ou Install 1 Choose a location for the base near an electrical outlet and a telephone jack. This phone requires a modular telephone jac k and a standard electrical outlet (110v A C) not controlled by a wall switc h. 2 Install the handset battery. b) Align two holes in plug with socket pins, and snap the plug into place. d ...
-
AT&T 9341 - page 7
INST ALL A TION 5 3 Attach belt clip to the cordless handset (optional) . T o attach T o r emov e T ab le/Desk Installation Standard electrical outlet Modular telephone jack 1 Connect the telephone line cord. 2 Connect the power cord. 9341_book_1ATT 6/14/00 4:07 PM Page 5 ...
-
AT&T 9341 - page 8
INST ALLA TION 6 3 Char ge the handset battery. Place the handset in the base. Charge the battery for at least 16 hours the first time. 4 Check for dial tone. After the batteries are charg ed, pick up the handset and press P ; you should hear a dial tone. 5 Set the dial mode. If you hav e touch tone service, the phone is ready to use as soon as the ...
-
AT&T 9341 - page 9
INST ALLA TION 7 a) Align holes on base with mounting studs on wall jack. b) Place power cord as shown, so it hangs straight down between base and wall. c) Pull base down on mounting studs until it locks into place. 5 Follow Steps 3–5 in T able/Desk Installation. 2 Connect the telephone line cord . 3 Connect the power cord. 4 Mount the base on th ...
-
AT&T 9341 - page 10
Time/Date 1 Press G until the screen displays 2 Press S . The month f lashes. 3 Use < or > to select the current month. 4 Press S . 5 Repeat Steps 3 and 4 to set the day , hour , minute and AM or PM. Ringer Selection 1 Press G until the scr een displays 2 Press > to select 1 , 2 , 3 , 4 , or OFF . Y ou hear a sample of each ring display ed ...
-
AT&T 9341 - page 11
TELEPHONE OPERA TION 9 End a Call Press O — OR — Place handset in base Exit progr amming. Cancel a page. Handset V olume While on a call, adjust volume of what y ou hear . Hold Press to put a call on hold. Press again to release hold, or lift the handset of an e xtension. Answ er a Call Pr ess any key e xcept O . Change Channel Switc h to a cle ...
-
AT&T 9341 - page 12
TELEPHONE OPERA TION 10 Page/ Handset Locator Pr ess to page the handset for up to 90 seconds. Press again to cancel, or press any key on handset. On steadily when handset is in use or is charging in base On steadily when y ou have unr eviewed call inf ormation. If y ou subscribe to telephone company v oice mail with a visual message waiting signal ...
-
AT&T 9341 - page 13
TELEPHONE OPERA TION 11 T emporar y T one Dialing If you hav e dial pulse (rotar y) ser vice, you can chang e from dial pulse to touch tone dialing during a call by pressing * . This is useful if you need to send touch tone signals f or access to telephone banking or long-distance ser vices. 1 Dial the number . 2 Press * . Buttons pressed after thi ...
-
AT&T 9341 - page 14
TELEPHONE OPERA TION 12 Displa y Screen Messages Screen Displa ys: When: STANDBY The handset is not in use. NO LINE The base is not connected to the telephone line, or the line is not wor king. RINGING There is a call coming in. CONNECTING The handset is waiting f or a dial tone. PHONE ON The handset is in use. MESSAGE WAITING Y ou have receiv ed t ...
-
AT&T 9341 - page 15
TELEPHONE MEMOR Y 13 This cordless phone can store 50 telephone numbers with names, each up to 16 digits long. Stor e Memor y Numbers 1 Mak e sure the handset is off. 2 Press M . The first available location is displa yed in the lower right cor ner of the screen. 3 Using the chart below , enter up to 16 char acter s for the name you’ re stor ing ...
-
AT&T 9341 - page 16
Edit Numbers Stor ed in Memor y 1 Press < to r eview number s stored in memor y . 2 Press S when the screen displa ys the number you want to edit. EDIT f lashes on the screen. 3 Edit the name/number display ed. Press > to switc h between name and number . 4 Press S to sav e the edited information. Delete Numbers Stor ed in Memor y Delete a Sp ...
-
AT&T 9341 - page 17
Dial Memor y Numbers 1 Press P . 2 Press M , then enter the memory location (01-50) — OR — 1 Press < under the phonebook icon ( ) to review numbers stored in memor y . 2 Press < or > until the screen displa ys the number you want to call, or enter the first letter of the name stored with the number . 3 Press P . TELEPHONE MEMOR Y 15 93 ...
-
AT&T 9341 - page 18
C ALLER ID OPERA TION 16 About Call Histor y This phone assigns each incoming call a number fr om 1 to 50. The most recent call will hav e the highest number . When the memor y is full, the oldest call information is deleted to make room f or new incoming call information. For eac h call that comes in, the screen displays the f ollowing information ...
-
AT&T 9341 - page 19
C ALLER ID OPERA TION 17 Delete Call Histor y Delete a Specific Call 1 Press > until the scr een displays the call information you w ant to delete. 2 Press S , then press > until DEL is f lashing. 3 Press S , then press < or > until the scr een displays DELETE? YES . 4 Press S . Y ou’ ll hear a ser ies of beeps confirming the deletion ...
-
AT&T 9341 - page 20
C ALLER ID OPERA TION 18 Stor e Call in Memor y 1 Press > until the scr een displays the call information you w ant to store. 2 Press S twice. 3 Press S to store the call inf ormation in the memor y location display ed in the upper r ight corner — OR — Press < , then enter a tw o-digit memor y location (01-50). 4 Press S . Y ou’ ll hear ...
-
AT&T 9341 - page 21
C ALLER ID OPERA TION 19 Call Block This featur e works with service available from your phone service provider to prevent y our call information from being seen by the people you call. T o activate call b lock ser vice, you must enter y our ser vice provider’ s call block code eac h time you make a call. Y ou can set the phone to automatically d ...
-
AT&T 9341 - page 22
Displa y Screen Messages Screen Displa ys: When: PRIVATE NAME The other par ty is blocking name inf or mation. PPP The other party is blocking number inf or mation. PRIVATE CALLER The other party is blocking name and number information. UNKNOWN NAME Y our phone company is unab le to receive information about this caller’ s name. UUU Y our phone c ...
-
AT&T 9341 - page 23
Char ging the Handset Ba tter y P ack This batter y should remain charg ed up to six days with the ringer turned on and up to 12 days with the ring er of f. A fully charg ed batter y provides an aver a ge talk time of about fiv e hour s. The batter y pack needs charging when: • A new batter y is installed in the handset. • The phone beeps twice ...
-
AT&T 9341 - page 24
BA TTERIES 22 Nickel-Cadmium Rechargeable Batteries m ust be recycled or disposed of pr operly . Do not dispose of in household garbage. If bur ned, it could explode. If punctured, it could release caustic material which could injure the skin or eyes. If swallo wed, it ma y be toxic. The RBRC ™ seal means that the manufacturer is v oluntar ily pa ...
-
AT&T 9341 - page 25
IN C ASE OF DIFFICUL TY 23 If you hav e dif ficulty operating this phone, tr y the suggestions belo w . For Customer Service, visit our website at www .telephones.att.com or call 1 800 222–3111. Please retain your r eceipt as your pr oof of pur chase . If the phone doesn’ t work at all, check these items first: • Mak e sure the A C adapter is ...
-
AT&T 9341 - page 26
IN C ASE OF DIFFICUL TY 24 If y ou hear noise or interference when using the phone: • Mak e sure the base antenna is full y upr ight. • Y ou may be out of rang e. Move c loser to the base. • Press and release G to c hange to another of the 30 c hannels available. If noise is exceptionall y loud, move closer to the base bef ore changing c hann ...
Haben Sie eine Frage bezüglich AT&T 9341?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit AT&T 9341 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit AT&T 9341 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.