Bedienungsanleitung GE 000 gpd

45 Seiten 0.27 mb
Download

Zur Seite of 45

Summary
  • GE 000 gpd - page 1

    E4H-CE AND E8-CE SERIES W A TER PURIFICA TION MACHINES 3 m 3 /hr to 45 m 3 /hr 18,000 gpd to 288,000 gpd Operation and Maintenance Manual ...

  • GE 000 gpd - page 2

    ...

  • GE 000 gpd - page 3

    INSTRUCTIONS FOR E4H-CE AND E8-CE W A TER PURIFICA TION OPERA TION AND MAINTENANCE MANUAL T ABLE OF CONTENTS Page 1.0 DESCRIPTION 1 1.1 Definitions 1 1.1.1 Permeate Rate 1 1.1.2 Concentrate Rate 1 1.1.3 Feed Rate 1 1.1.4 Reverse Osmosis 1 1.1.5 Membrane Elements 2 1.1.6 Clean-In-Place 2 1.1.7 Flow Control Center 2 1.1.8 A verage Pressure 2 1.1.9 Co ...

  • GE 000 gpd - page 4

    Page 4.0 MACHINE OPERA TION AND MAINTENANCE 17 4.1 Daily Log Sheets 17 4.2 Pre-Filter Cartridge 17 4.3 Cleaning 17 4.4 Draining Machine for Shipment 19 4.5 Membrane Element Replacement 19 4.6 Membrane Element Removal 21 5.0 FIELD INST ALLED ACCESSORIES 22 5.1 Pretreatment Shutdown 22 5.2 Permeate Flush 22 5.3 Chemical Pump 24 5.4 Clean-In-Place Ins ...

  • GE 000 gpd - page 5

    Page LIST OF FIGURES Figure T itle 1.1 Normal V ersus Cross Flow Filtration 1 1.2 Membrane Element W ith Interconnectors 2 1.3 Principles of Operation 3 LIST OF T ABLES Figure T itle 1.1 Flow Specifications for E-CE Reverse Osmosis Machines 7 1.2 Minimum/Maximum Boost Pressure 8 1.3 Membrane Element Specifications 9 2.4 Feed W ater Requirements 10 ...

  • GE 000 gpd - page 6

    1.0 DESCRIPTION E-CE Series Reverse Osmosis (RO) machines are durable pieces of equipment, which, with prop- er care, will last for many years. These instructions give operation and maintenance details vital to the sustained performance of the machine. Please read completely before operating your machine. 1.1 Definitions The operating definitions p ...

  • GE 000 gpd - page 7

    1.1.5 Membrane Elements Membrane elements are interleaved layers of semi-permeable membrane, spacer , and permeate carrier spiraled around a central permeate tube make up the mem- brane element. Figure 1.2 Membrane Element with Interconnectors 1.1.6 Clean-In-Place The abbreviation for Clean-In-Place is CIP . 1.1.7 Flow Control Center The Flow Contr ...

  • GE 000 gpd - page 8

    C f = Feed Concentration C p = Permeate Concentration C c = Concentrate Concentration C avg = A verage Concentration in Machine 1.1.10 Salt (Ionic) Passage Ionic Salt Passage equals the percent of dissolved salts passed through the mem- brane element or 100% minus rejection. 1.1.1 1 Recovery Recovery equals permeate rate divided by feed rate and is ...

  • GE 000 gpd - page 9

    4 Rejection = [(C avg ) - (C P )] x 100 (C avg ) = [(237.5 mg/L) + (8.3 mg/L)] x 100 (237.5) = 96.5% Passage = (C P ) x 100 (C f ) = (8.3 mg/L) x 100 (237.5) = 3.5% Recovery = (Q P ) x 100 (Q f ) = (18 gpm) x 100 (24gpm) = 75% ...

  • GE 000 gpd - page 10

    1.2 Machine Nomenclature E-CE Series water purification machines are numbered in such a way as to indicate the permeate flow you can expect from the machine and other specifications: Example: RE, E8-CE-9, 400, 5, 66 - 75 1.3 Features E4H-CE and E8-CE water purification machines have all the features necessary for safe, continuous production of high ...

  • GE 000 gpd - page 11

    6 · Multi-stage centrifugal pump, SS construction (SS end castings and wetted parts, Noryl* internals) on the 3 to 3 to 34m 3 /hr and AS (all Stainless Steel components) on the 45m 3 /hr . · Electrical package includes Programmable Logic Controller (PLC), IEC66 control enclosure with a 24VDC control circuit, Siemens TP070 operator interface termi ...

  • GE 000 gpd - page 12

    1.4 Specifications for E-CE Series Machines The machine flow specifications listed, T able 1.1 below , are based on 25 ° C (77 ° F) and 2000 ppm NaCl. T able 1.1 Flow Specifications for Reverse Osmosis E-CE Machines 7 MODEL Recovery Units Permeate Rate Concentrate Rate (50-66%) Concentrate Rate (75%) Feed Rate (50-66%) Feed Rate (75%) Recycle Rat ...

  • GE 000 gpd - page 13

    1.4.1 Feed W ater Specifications The feed water requirements listed in T able 1.1 must be met to ensure quality per- meate and extended membrane element life. 1.4.2 Permeate Flow Rate Stated in T able 1.1 and on the machine serial number label (assumes no permeate back pressure, 2000 mg/L T otal Dissolved Solids (TDS) maximum feed concen- tration, ...

  • GE 000 gpd - page 14

    1.4.5 Reverse Osmosis Membrane Element Rejection E8-CE RO machines use Fiberglass Reinforced Plastic (FRP). E4H-CE RO machines use tape wrapped membrane elements. For more information, refer to the Spare Parts List (P/N 1233377). T able 1.3 Membrane Element Specifications 9 Specification Outer Cover Material T ypical Ionic Rejection (TDS) Nominal P ...

  • GE 000 gpd - page 15

    2.0 INST ALLA TION The following installation guidelines will help you install your new E-CE RO machine. 2.1 Feed W ater Requirements The following feed water requirements must be met before installing your new E-CE RO machine to ensure quality permeate and extended membrane element life. T able 2.4 Feed W ater Requirements 2.2 Mounting E-CE Series ...

  • GE 000 gpd - page 16

    membrane element housings for removal and loading of membrane elements. If 1 14 cm (45-inches) are not available, the entire membrane element housing may need to be removed for membrane element replacement. 2.3 Plumbing The E4H-CE and E8-CE come with flanged connections installed on all isolation valves. T able 2.5 Connections 2.4 Power and Electri ...

  • GE 000 gpd - page 17

    3.0 PREP ARA TION AND ST AR T -UP 3.1 Pretreatment for W ater Purification All systems will operate most efficiently on filtered water with a pH of less than 6.5 and a Silt Density Index (SDI) of 5 or below . If the machine is operated on higher pH water, other forms of pretreatment may be necessary . A water analysis prior to start-up of the machi ...

  • GE 000 gpd - page 18

    STEPS 1. Recheck the function and integrity of your pretreatment equipment. Ensure that your water softener , activated carbon filters, and iron filters (where applicable) have been leaked checked, back washed, and thoroughly rinsed for service before starting up your RO unit. 2. Attach the feed water pipe to the inlet of the machine. The standard ...

  • GE 000 gpd - page 19

    It is also important to understand the relationship of these two valves, the pressure gauge, and your RO pump. The pump has a fixed amount of flow produced, and the valves are the control devices to distribute this fixed flow amount. The pres- sure gauge is an indicator of applied membrane element pressure a the flows set by the valves 8. Press the ...

  • GE 000 gpd - page 20

    15. As the machine purges the air and fills with water , the pressure will gradually increase. W ater should flow through the permeate and concentrate piping, viewed on the individual flow meters. If you do not see flow , turn the machine OFF and return to Section 3.2 (Initial Start-Up). 16. Gradually adjust the concentrate flow control valve. As y ...

  • GE 000 gpd - page 21

    3.3 Daily Start-Up Check the machine to insure isolation valves are in the proper positions for operation. T o turn the RO ON, press the RO button so it is in the ON position. If the alarm light is lit, push the “Alarm Reset” switch on the control enclosure and the alarm button on the OIT . If the alarm light stays lit, check the RO for an alar ...

  • GE 000 gpd - page 22

    4.0 MACHINE OPERA TION AND MAINTENANCE The operation and maintenance of a E-CE RO Series machine is relatively simple, but requires regular data recording and routine preventative maintenance. It cannot be emphasized enough the importance of filling out the Daily Log Sheet (Section 7.3) during each operating shift. A Start- Up Data Sheet was comple ...

  • GE 000 gpd - page 23

    flow and/or rejection of salts, or an increased pressure drop across the machine will indi- cate when cleaning is required. GE Osmonics recommends cleaning at least every month to assure good membrane element performance and long membrane element life. GE Osmonics offers a full line of chemical cleaners for specific cleaning needs. Refer to the Spa ...

  • GE 000 gpd - page 24

    reestablish normal operation. Operate the machine as described in the flushing section for at least one hour . The deter gent is sufficiently flushed when the per- meate conductivity is restored to its normal previous level. When conductivity is back to normal, divert the permeate and concentrate back to service positions. 4.4 Draining Machine for ...

  • GE 000 gpd - page 25

    2. Cut the bag open as close as possible to the seal at the end of the bag, so that the bag may be reused if necessary . 3. Remove the membrane element from the bag and remove the foam protectors from each end of the membrane element. 4. Remove the parts from the parts container (if included) and inspect. Make sure all parts are clean and free of d ...

  • GE 000 gpd - page 26

    4.6 Membrane Element Removal As time progresses, the efficiency of the membrane element will be reduced. In general, the salt rejection does not change much until two or three years after installation, when operated on properly pretreated feed water and routine maintenance performed. The per- meate flow rate will begin to decline slightly after one ...

  • GE 000 gpd - page 27

    5.0 FIELD INST ALLED ACCESSORIES 5.1 Pretreatment Shutdown E-CE Series RO machines are equipped with Pretreatment Shutdown control capability . Pretreatment Shutdown is the ON/OFF control of the RO via a signal from a remote device. External Control can be used when Permeate Flush is not desired prior to RO shutdown (Permeate Flush, Section 5.2). T ...

  • GE 000 gpd - page 28

    centration of the diluted feed stream, at the operating recovery , is that the water in the machine at shutdown will have total dissolved solids (TDS) concentrations approximate- ly equal to the machine feed TDS level. The low TDS environment created reduces the potential for membrane element fouling during the down period, extending membrane ele- ...

  • GE 000 gpd - page 29

    4. T urn the AUTO/HAND Button on the Pur ge Button located on the OIT to the “AUTO” position. W ith multiple remote devices wired in series, as described above, an open contact from any of the configured devices will activate the Permeate Purge Cycle. 5.3 Chemical Pump GE Osmonics offers a stand-alone chemical pump and tank that can be used to ...

  • GE 000 gpd - page 30

    6.0 TROUBLESHOOTING This troubleshooting guide can assist you in identifying common operating problems you may experience with your machine. The operator can easily correct many of these problems, howev- er , for those that persist or are not understood you should contact the GE Osmonics Customer Support Center . Have the following information avai ...

  • GE 000 gpd - page 31

    26 TROUBLESHOOTING SYMPTOM Low operating pressur e (continued) Low permeate flow rate POSSIBLE CAUSES Insufficient electrical power Pump not operating correctly Low operating pressure Dirty or fouled membrane elements Operating on cold water less than 13 ° C (55 ° F) Membrane elements installed backward or damaged concen- trate seal Flow meter in ...

  • GE 000 gpd - page 32

    27 TROUBLESHOOTING SYMPTOM Low permeate flow rate (continued) Low concentrate flow rate, normal or higher than normal pressur e POSSIBLE CAUSES Operating on cold water less than 13 ° C (55 ° F) Membrane elements installed backward or damaged concen- trate seal Concentrate valve plugged Concentrate outline line restricted Flow meter inaccurate Dir ...

  • GE 000 gpd - page 33

    SYMPTOM High operating pressur e W ater flowing when machine is turned OFF Declining rejection (high permeate conductivity) POSSIBLE CAUSES Recycle or concentrate valve plugged Inaccurate pressure gauge Restricted flow after pump outlet T elescoped membrane ele- ment covering membrane ele- ment housing outlet port Inlet solenoid valve not clos- ing ...

  • GE 000 gpd - page 34

    29 TROUBLESHOOTING SYMPTOM Declining rejection (high permeate conductivity) (continued) Machine not operating POSSIBLE CAUSES O-ring seal broken or dam- aged Change in incoming water quality Inaccurate conductivity moni- tor or fouled probe Pressurized storage switch or float switch has cut power to machine External control or permeate purge contro ...

  • GE 000 gpd - page 35

    30 TROUBLESHOOTING SYMPTOM Machine not operating (continued) Electrical machine shut down POSSIBLE CAUSES Thermal overload in motor has tripped No power to machine Motor and/or pump not oper- ating properly Alarm condition has turned OFF machine Alarm condition has turned OFF machine External control or permeate purge control contacts have been shu ...

  • GE 000 gpd - page 36

    TROUBLESHOOTING SYMPTOM Electrical machine shut down (continued) Conductivity drifts or changes after calibration Display is blank pH reading is off by mor e than 1pH unit POSSIBLE CAUSES Motor starter overloaded, heater tripped. Calibration may have been done before the reading stabi- lized The stable line may contain electrical noise T urbine met ...

  • GE 000 gpd - page 37

    TROUBLESHOOTING 32 SYMPTOM Chemical pump will not feed chemical Chemical pump feed reverse of what you expect- ed POSSIBLE CAUSES Pumping may be affected by other software variables Relay set point not properly configured REMEDIES Is the relay turned ON or OFF? Is the CIP input activated? Y ou must have permeate or concentrate flow for a relay conf ...

  • GE 000 gpd - page 38

    7.0 FORMS 7.1 RETURN GOODS AUTHORIZA TION (RGA) If you wish to return goods for repair , warranty evaluation and/or credit, please have your original sales order or invoice available when you call GE Osmonics. Call GE Osmonics at (800) 848 - 1750 and ask to speak with Customer Service. A GE Osmonics Customer Service representative will provide inst ...

  • GE 000 gpd - page 39

    34 E-SERIES ST AR T -UP DA T A SHEET Customer: Model Number: Serial Number: Date: T ested By Units (Circle One) Data Data Remarks Permeate Rate T otal Flow Rate Pre-Filter Pr essure Post-Filter Pressur e Primary Pressur e Final Pressur e Feed TDS Concentrate TDS A vg TDS Permeate TDS (manual) Permeate TDS (meter uS) % Passage (Perm TDS/A vg TDS) Ch ...

  • GE 000 gpd - page 40

    35 7.3 Daily Log Sheet NAME OF COMP ANY NOTE : Please record all calibrations of instruments or other occurrences related to this system. This is a template. Make copies as needed. *Symbols: Q - Flow Rate; C - Conductivity Reference the T roubleshooting Guide in your Instruction Manual where trends or differences are noted . DA TE AND TIME PRE-FILT ...

  • GE 000 gpd - page 41

    8.0 W ARRANTY 8.1 W arranty T erms Subject to the terms and conditions set forth hereinafter , Seller (GE Osmonics, Inc. or any of its authorized subsidiaries) warrants to the original purchaser (hereafter the “Buyer”) that the products manufactured by Seller are free from defects in material and in work- manship for twelve (12) months from the ...

  • GE 000 gpd - page 42

    discretion, be the sole judge of whether a returned product or component is defective in material or workmanship. Required or replaced products or components shall be returned freight. In genuine emergency situation, Seller will (at Seller’ s sole option) forward replacement parts to Buyer without waiting for authorized return of the questionable ...

  • GE 000 gpd - page 43

    NO W ARRANTY OR OTHER LIABILITY OF SELLER TO BUYER UNDER THIS AGREEMENT OR OTHER WISE WILL IN ANY EVENT EXCEED THE COST OF REPLACEMENT OF THE APPLICABLE SELLER PRODUCT , P AR T , OR ACCESSO- R Y THA T IS SUBJECT TO ANY BREACH OF SELLER’S W ARRANTY . SELLER WILL NOT BE LIABLE FOR ANY DAMAGE T O ANY PROPER TY OF BUYER OR TO BUYER’S CUST OMERS FOR ...

  • GE 000 gpd - page 44

    ...

  • GE 000 gpd - page 45

    Corporate Headquarters 5951 Clearwater Drive Minnetonka, MN 55343-8995 USA (952) 933-2277 Phone (952) 933-0141 Fax Euro/Africa Operations 230 rue Robert Schuman Z A des Uselles F-77350 Le MØe sur Seine FRANCE +33 1 64 10 2000 Phone +33 1 64 10 3747 Fax Asia/Pacific Operations 1044/8 SOI 44/2 Sukhumvit Road Prakanong Bangkok 10110 THAILAND +66 2 38 ...

Produzent GE Kategorie Water System

Dokumente, die wir vom Produzenten des Geräts GE 000 gpd erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen GE
- Bedienungsanleitungen 000 gpd
- Produktkarten GE
- Informationsbroschüren
- oder Energieetiketten GE 000 gpd
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung GE 000 gpd.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen GE 000 gpd, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen GE 000 gpd. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts GE 000 gpd ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts GE 000 gpd, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von GE 000 gpd hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von GE 000 gpd verständlich ist.

Eine gänzliche Bedienungsanleitung von GE sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von GE 000 gpd bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von GE 000 gpd befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich GE 000 gpd, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts GE 000 gpd - die uns die ersten Schritte während der Nutzung von GE 000 gpd erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit GE 000 gpd hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von GE 000 gpd im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich GE 000 gpd?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit GE 000 gpd nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit GE 000 gpd hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)