Deutsch dropdown-ico

Bedienungsanleitung Snapper ERP2187519BV, EP2187519BV

32 Seiten 1.59 mb
Download

Zur Seite of 32

Summary
  • Snapper ERP2187519BV, EP2187519BV - page 1

    Safety Instructions & Operator's Manual for NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for further details. Manual No. 7101607 ...

  • Snapper ERP2187519BV, EP2187519BV - page 2

    Thank Y ou for pur chasing this quality-built Snapper product. We’re pleased that you placed your confidence in the Snapper brand. When operated and maintained according to the instructions in this manual, your Snapper product will provide many years of dependable service. This manual contains safety information to make you aware of the hazards a ...

  • Snapper ERP2187519BV, EP2187519BV - page 3

    1 Operator Safety Features and Controls Operation Maintenance T roubleshooting Warranties T able of Contents Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Decal Identification ...

  • Snapper ERP2187519BV, EP2187519BV - page 4

    www .snapper .com 2 Operator Safety ! ! Important Operator Safety Instructions WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The o ...

  • Snapper ERP2187519BV, EP2187519BV - page 5

    3 Operator Safety ! ! Important Operator Safety Instructions (Continued) Safe Handling of Gasoline (Continued From Previous Page) 6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner . Always place the contain- ers on the ground away from the vehicle before filling. 7. Remove gas-powered equipment from t ...

  • Snapper ERP2187519BV, EP2187519BV - page 6

    www .snapper .com 4 Operator Safety (2) Warning Instructions: A. Read, understand and follow instructions and warnings in the operator’ s manual, as well as on the mower , engine and attachments before operating. B. Indicates possible severe injury from rotating cutting blades. C. Do not operate without entire grass catcher or guard in place. D. ...

  • Snapper ERP2187519BV, EP2187519BV - page 7

    5 Operator Safety (3) Engine Speed Control: Indicates direction to increase engine RPM (hare), decrease engine RPM (tortoise). (4) Speed Selector: Shows direction of motion and the ability to select ground speed by moving lever forward or backward. Decal Identification (Continued) (5) Operator Presence Control (OPC): Arrow points to the OPC bail. W ...

  • Snapper ERP2187519BV, EP2187519BV - page 8

    www .snapper .com 6 Features and Controls IMPORT ANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your Snapper dealer if you have questions. Features and Controls A. Oil Fill Cap and Dipstick B. Fuel Filler Cap C. Recycling Cover D. Rear Height Adjustment Latch (2) E. ...

  • Snapper ERP2187519BV, EP2187519BV - page 9

    7 Operation Pre-Start Check List Make the following checks and perform the ser vice required before each start-up. 1. Check the guards, deflectors, grass bag, adapter , and covers to make sure all are in place and securely tightened. 2. Check the blade control (A, Figure 1) , wheel drive control (B) , and ground speed control (C) to insure they wor ...

  • Snapper ERP2187519BV, EP2187519BV - page 10

    www .snapper .com 8 Operation Starting and Operation (Continued) Propelling the Mower 1. Start the engine. Refer to the Section entitled “Starting and Operation – Engine and Blade”. 2. Move the ground speed control (A, Figure 5) to the desired speed position. 3. Squeeze the wheel drive control (B) against the handle to engage the wheel drive ...

  • Snapper ERP2187519BV, EP2187519BV - page 11

    9 Operation Cutting Height Adjustment 1. Pull the height adjusting latch (A, Figure 7) outward and move to the desired cutting height. 2. Set all wheels at the same cutting height. The highest cutting position is Notch 7 (Figure 8) . The lowest cutting position is Notch 1. Recycling Operation Note: For best recycling results, cut up to a maximum of ...

  • Snapper ERP2187519BV, EP2187519BV - page 12

    www .snapper .com 10 Operation Installing the Discharge Deflector 1. Remove the recycling cover . Refer to the Section entitled “Recycling Operation”. 2. Install the deflector (A, Figure 10) to the deck in place of the recycling cover , making sure that: The front hole (B) on the outside front of the deflector fits over the stud where the front ...

  • Snapper ERP2187519BV, EP2187519BV - page 13

    11 Operation Installing the Recycling Plug (Optional Accessory on Some Models) 1. Once the adapter has been installed, recycling may be desired. Insert the recycling plug (A, Figure 12) com- pletely and securely into the adapter (B) . Install the grass bag as a safeguard. 2. Refer to the Section entitled “Recycling Operation”. Installing the Gr ...

  • Snapper ERP2187519BV, EP2187519BV - page 14

    www .snapper .com 12 Maintenance Maintenance - Introduction T o retain the quality of the mower , use genuine SNAPPER replacement parts only . Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower , always mention the model and serial number . Ser vice - After First 5 Hours Chang ...

  • Snapper ERP2187519BV, EP2187519BV - page 15

    13 Maintenance Check Mower Blade 1. Disconnect the spark plug wire and secure the end away from the plug. 2. Tilt the mower up on its rear wheels for access to the blade cap screw (A, Figure 17) . Do not tilt the mower with the spark plug or carburetor down. Important: Drain the fuel tank before tipping the mower . DO NOT tip the machine with the c ...

  • Snapper ERP2187519BV, EP2187519BV - page 16

    www .snapper .com 14 Maintenance Mower Blade Replacement Standard Blade Wear Limit 1. Inspect the blade (Figure 18) frequently for signs of excessive wear or damage: (A) New blade (B) Wear limit (notch starts) (C) Dangerous condition! Do not use on the mower! Replace with a new blade. Ninja Blade Wear Limit 1. Inspect the blade (Figure 19) frequent ...

  • Snapper ERP2187519BV, EP2187519BV - page 17

    15 Maintenance Blade Sharpening (Continued) 4. Sharpen the blade on a grinding wheel at an angle of 22 to 28 degrees (B, Figure 21) . DO NOT sharpen the blade beyond the original cutting edge (A) . 5. Check blade for balance. If necessary , correct balance by grinding heavy end of blade. 6. Reinstall blade (B, Figure 20) . Note the correct assembly ...

  • Snapper ERP2187519BV, EP2187519BV - page 18

    www .snapper .com 16 Maintenance Driven and Drive Disc Ser vice If the mower does not propel itself properly , check for the following problems: 1. Grease on the drive disc (A, Figure 23) causing slippage. 2. Broken or disconnected drive spring (B) . 3. Driven disc (C) is out of adjustment. 4. Driven disc rubber is worn - does not contact drive dis ...

  • Snapper ERP2187519BV, EP2187519BV - page 19

    17 Maintenance Driven Disc Adjustment (Continued) 2. Remove the driven disc spring (A, Figure 26) from the driven disc assembly (B) . Also remove the pin and washer (C) from the transfer rod (D) , and remove the end of the transfer rod from the hole in the driven disc assembly . 3. Slide the driven disc assembly over to 1/8” (A, Figure 27) from t ...

  • Snapper ERP2187519BV, EP2187519BV - page 20

    www .snapper .com 18 Maintenance Driven Disc Replacement (Continued) 2. Using needle nose pliers, unhook the drive spring (A, Figure 29) and slide the driven disc assembly off the hex shaft. 3. Remove the two snap rings (A, Figure 30) which secure the rubber driven disc (B) to the driven disc assembly . 4. Install a new rubber driven disc onto the ...

  • Snapper ERP2187519BV, EP2187519BV - page 21

    19 Maintenance Replacing the Bearing On the Pulley End Of the Hex Shaft T o replace the bearing on the pulley end of the hex shaft, proceed as follows: 1. Hold the hex shaft with an adjustable wrench held next to the pulley . 2. Remove the 3/8” hex lock nut (B, Figure 31) , located on the outside of the right wheel bracket. 3. Remove the holder ( ...

  • Snapper ERP2187519BV, EP2187519BV - page 22

    www .snapper .com 20 Maintenance Engine Drive Belt Replacement (Stretch T ype Belts - Continued) IMPORT ANT : Drain the fuel tank before tipping the mower . DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination ...

  • Snapper ERP2187519BV, EP2187519BV - page 23

    21 Maintenance ITEM SERVICE PERFORMED REF . EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 7 X Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre-Cleaner Clean Sponge Element Engine Manual X** Air Cleaner Clean or Replace Engine Manual X** Spark Plug Replace Engine Manual X Engine Cooling System Cl ...

  • Snapper ERP2187519BV, EP2187519BV - page 24

    www .snapper .com 22 T roubleshooting PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start Using Recoil Starter 1. Fuel tank empty . 1. Fill fuel tank with fresh fuel. 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for Instructions. 3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug. Engine ...

  • Snapper ERP2187519BV, EP2187519BV - page 25

    23 Warranties 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original pur chaser’ s residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective i ...

  • Snapper ERP2187519BV, EP2187519BV - page 26

    www .snapper .com 24 Notes ...

  • Snapper ERP2187519BV, EP2187519BV - page 27

    25 ...

  • Snapper ERP2187519BV, EP2187519BV - page 28

    www .snapper .com 26 Notes ...

  • Snapper ERP2187519BV, EP2187519BV - page 29

    27 Notes ...

  • Snapper ERP2187519BV, EP2187519BV - page 30

    www .snapper .com 28 Notes ...

  • Snapper ERP2187519BV, EP2187519BV - page 31

    29 Notes ...

  • Snapper ERP2187519BV, EP2187519BV - page 32

    www .snapper .com Snapper Products 535 Macon Street McDonough, GA 30253 1-800-935-2967 30 EUROPEAN 21” STEEL DECK W ALK MOWERS SERIES 19 Engine Power Rating Information: The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & T orque Rating Pr ...

Produzent Snapper Kategorie Lawn Mower

Dokumente, die wir vom Produzenten des Geräts Snapper ERP2187519BV, EP2187519BV erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Snapper
- Bedienungsanleitungen ERP2187519BV, EP2187519BV
- Produktkarten Snapper
- Informationsbroschüren
- oder Energieetiketten Snapper ERP2187519BV, EP2187519BV
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Snapper ERP2187519BV, EP2187519BV.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Snapper ERP2187519BV, EP2187519BV, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Snapper ERP2187519BV, EP2187519BV. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Snapper ERP2187519BV, EP2187519BV ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Snapper ERP2187519BV, EP2187519BV, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Snapper ERP2187519BV, EP2187519BV hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Snapper ERP2187519BV, EP2187519BV verständlich ist.

Eine gänzliche Bedienungsanleitung von Snapper sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Snapper ERP2187519BV, EP2187519BV bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Snapper ERP2187519BV, EP2187519BV befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Snapper ERP2187519BV, EP2187519BV, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Snapper ERP2187519BV, EP2187519BV - die uns die ersten Schritte während der Nutzung von Snapper ERP2187519BV, EP2187519BV erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Snapper ERP2187519BV, EP2187519BV hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Snapper ERP2187519BV, EP2187519BV im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Snapper ERP2187519BV, EP2187519BV?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Snapper ERP2187519BV, EP2187519BV nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Snapper ERP2187519BV, EP2187519BV hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)