-
Ferris Industries 5900972 - page 1
5100647 Revision T Tractor: Model Number: Description 5900633 CCWKAV19, 5900635 CCWKAV25, 5900637 CCWKAV19CE, 5900638 CCWKAV25CE, 5900972 CCWKAV26, Mower Deck: Model Number: Description 5900636 CCW/48, 48” Cut 5900644 CCW/52, 52” Cut 5900645 CCW/61, 61” Cut 5900646 CCW/48CE, 48” Cut 5900647 CCW/52CE, 52” Cut OPERATOR’S MANUAL Comfort Co ...
-
Ferris Industries 5900972 - page 2
Briggs & Stratton Power Products Group, LLC Copyright © 2012 Briggs & Stratton Corporation Milwaukee, WI, USA. All rights reserved. Ferris is a trademark of Briggs & Stratton Corporation Milwaukee, WI, USA. Contact Information: Briggs & Stratton Power Products Group, LLC 5375 N. Main St. Munnsville, NY 13409-4003 (800) 933-6175 www ...
-
Ferris Industries 5900972 - page 3
Safety Rules & Information ............................... 2 Identification Tags ............................................. 8 Safety Decals ...................................................... 9 Safety Interlock System .................................. 10 Safety Icons ...................................................... 11 Features & ...
-
Ferris Industries 5900972 - page 4
2 Safety Rules & Information Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Do not operate this machine unless you have been trained. Reading and understanding this operator’s manual is a way t ...
-
Ferris Industries 5900972 - page 5
3 Safety Rules & Information Slope Operation You could be seriously injured if you use this unit on too steep of a slope. Using the unit on a slope that is too steep where you do not have adequate footing and unit traction (and control) can cause you to lose control and possibly slip and fall or roll the unit over. Always mow across slopes, not ...
-
Ferris Industries 5900972 - page 6
4 Safety Rules & Information Enclosed Areas Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers. The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death. Fuel and Maintenance Always disengage all drives, shutoff the e ...
-
Ferris Industries 5900972 - page 7
5 2. Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards. 3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided. 4. Be sure of your footing while using pedestrian controlled equipment, espec ...
-
Ferris Industries 5900972 - page 8
6 Safety Rules & Information 23. Use care when approaching blind corners, shrubs, trees or other objects that may obscure vision. 24. To reduce fire hazard, keep unit free of grass, leaves & excess oil. Do not stop or park over dry leaves, grass or combustible materials. 25. OSHA regulations may require the use of hearing protection when ex ...
-
Ferris Industries 5900972 - page 9
7 Safety Rules & Information SERVICE AND MAINTENANCE To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. ...
-
Ferris Industries 5900972 - page 10
8 www.ferrisindustries.com Identification Numbers North American Models CE Models SAMPLE SAMPLE When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your model/serial number and engine serial numbers on the space provided for easy access. These numbers can be found in the location ...
-
Ferris Industries 5900972 - page 11
Safety Decals SAFETY DECALS Before operating your unit, read the safety decals. The cautions and warnings are for your safety. To avoid a personal injury or damage to the unit, understand and follow all the safety decals. 9 NORTH AMERICAN MODELS CE MODELS (EXPORT) ALL MODELS 1 2 3 4 5 6 7 8 9 10 3 2 4, 9, 10 8 5, 9, 10 1 6, 7 This decal is installe ...
-
Ferris Industries 5900972 - page 12
10 www.ferrisindustries.com Safety Interlock System / Safety Icons SAFETY INTERLOCK SYSTEM This unit is equipped with safety interlock switches. These safety systems are present for your safety, do not attempt to bypass safety switches, and never tamper with safety devices. Check their operation regularly. Operational SAFETY Checks Test 1 — Engin ...
-
Ferris Industries 5900972 - page 13
11 CE SAFETY ICONS Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing. Remove the key and consult technical literature before performing repairs or maintena ...
-
Ferris Industries 5900972 - page 14
12 www.ferrisindustries.com CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section. Please t ...
-
Ferris Industries 5900972 - page 15
13 Features & Controls Neutral Return Pedal The neutral return pedal provides a hands-free return to neutral. This is used in conjunction with the Reverse Speed Control Levers (B) to properly stop the machine. See the Operation section for steering instructions. Fuel Tank Cap To remove the cap, turn counterclockwise. Cutting Height Adjust Handl ...
-
Ferris Industries 5900972 - page 16
14 www.ferrisindustries.com CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section. Please t ...
-
Ferris Industries 5900972 - page 17
15 Features & Controls Parking Brake Handle The parking brake is released by pushing DOWN on the parking brake handle until it stops. To engage the parking brake, pull UP on the handle until it locks over center. Engine Kill/Operator Presence Handles These handles are a major factor in the safety interlock system of the mower. The handles are n ...
-
Ferris Industries 5900972 - page 18
16 www.ferrisindustries.com GENERAL OPERATING SAFETY Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower. • Become familiar with all of the controls and how to stop the unit. • Drive in an open area without mowing to become accustomed to the un ...
-
Ferris Industries 5900972 - page 19
17 WARNING If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now. Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls. STARTING THE ENGINE 1. Engage the parking brake and make sure the PTO switch is di ...
-
Ferris Industries 5900972 - page 20
18 www.ferrisindustries.com Operation Figure 3. Forward Travel. A. Forward Speed Control Lever Figure 4. Reverse Travel. A. Reverse Steering Control Levers Figure 5. Left Turn Travel. A. Left Hand Steering Control Lever DRIVING THE MOWER NOTE: Before attempting to drive the mower make sure you have read the Features and Controls section and underst ...
-
Ferris Industries 5900972 - page 21
19 Operation Figure 7. Increase Speed To The Left Wheel. A. Left Hand Forward Speed Override Lever Figure 8. Increase Speed To The Right Wheel. A. Right Hand Forward Speed Override Lever Figure 6. Right Turn Travel. A. Right Hand Steering Control Lever To make a right-hand turn (See Figure 6): Gently squeeze the right hand steering control lever (A ...
-
Ferris Industries 5900972 - page 22
20 www.ferrisindustries.com Operation MOWING Before mowing, set the cutting height as described in the Troubleshooting, Adjustments & Repair section. 1. Engage the parking brake. Make sure the PTO switch is disengaged and the motion control lever is in the NEUTRAL position. 2. Start the engine (see STARTING THE ENGINE). 3. Set the throttle to F ...
-
Ferris Industries 5900972 - page 23
21 When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: 1. Mow when the grass is between three and five inches high. 2. Mow with sharp blades. Short clippings of grass one inch or shorter decompose more quickly than longer blades. Sha ...
-
Ferris Industries 5900972 - page 24
22 www.ferrisindustries.com PUSHING THE MOWER BY HAND 1. Disengage the PTO, engage the parking brake, turn the ignition OFF, and remove the key. 2. To disengage the transmissions (free-wheel position), lift the hydraulic release levers (A, Figure 9) located in front of the gas tank. Lock into position shown in Figure 9. 3. Disengage the parking bra ...
-
Ferris Industries 5900972 - page 25
23 Operation STORAGE Temporary Storage (30 Days Or Less) Remember, the fuel tank will still contain some gasoline, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation. Here is a che ...
-
Ferris Industries 5900972 - page 26
24 www.ferrisindustries.com MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your mower. You will need to keep a record of your operating time. Regular Maintenance SAFETY ITEMS Before Each Use Every 5 Hours Every 25 Hours Every 100 Hours Every 250 Hours Spring & Fall Check Safety Interlock Syste ...
-
Ferris Industries 5900972 - page 27
25 WARNING Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills. Do not remove fuel filter when engine is hot, as spilled gasoline may ignite. DO NOT spread hose clamps fur ...
-
Ferris Industries 5900972 - page 28
26 www.ferrisindustries.com CHECK HYDRAULIC OIL LEVEL 1. Observe the oil reservoir (B, Figure 11). The oil level should be at the “FULL” line (C). 2. Before removing the reservoir cap, make sure the area around the reservoir cap is free of dust, dirt, or other debris. 3. If necessary, unscrew the reservoir cap and add SAE straight 20 or 30 weig ...
-
Ferris Industries 5900972 - page 29
27 Regular Maintenance Figure 15. Lubrication Points Mower Deck Lubrication Points* LUBRICATION Lubricate the unit at the locations shown in Figure 15 as well as the following lubrication points. Grease: • front caster wheel axles & yokes • deck lift pivot blocks • mower deck spindles • mower deck idler arm Use grease fittings when pres ...
-
Ferris Industries 5900972 - page 30
28 www.ferrisindustries.com Regular Maintenance CLEANING THE BATTERY AND CABLES 1. Disconnect the cables from the battery, negative cable first (B, Figure 16). 2. Clean the battery terminals and cable ends with a wire brush until shiny. 3. Reinstall the battery and reattach the battery cables, positive cable first (A). 4. Coat the cable ends and ba ...
-
Ferris Industries 5900972 - page 31
29 SERVICING THE MOWER BLADES 1. Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps. 2. Remove the deck guard. 3. Raise the mower deck and secure with jack stands. 4. To remove blade for sharpening, use two (2) 15/16” wrenches to remove the nut from the top of the blade bolt. (Figure 17). 5. ...
-
Ferris Industries 5900972 - page 32
30 www.ferrisindustries.com TROUBLESHOOTING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies. See the inform ...
-
Ferris Industries 5900972 - page 33
31 Rider Troubleshooting Continued. PROBLEM CAUSE REMEDY Engine runs, but mower will 1. Transmission release lever(s) 1. Move into drive position. not drive. in “neutral” position. 2. Belt is broken. 2. See Drive Belt Replacement. 3. Drive belt slips. 3. See problem and cause below. 4. Brake is not fully released. 4. See authorized service deal ...
-
Ferris Industries 5900972 - page 34
32 www.ferrisindustries.com Troubleshooting, Adjustment & Repair TROUBLESHOOTING COMMON CUTTING PROBLEMS PROBLEM CAUSE REMEDY Streaking. 1. Blades are not sharp. 1. Sharpen your blades. 2. Blades are worn down to far. 2. Replace your blades. 3. Engine speed is too slow. 3. Always mow at full throttle. 4. Ground speed is too fast. 4. Slow down. ...
-
Ferris Industries 5900972 - page 35
33 Troubleshooting, Adjustment & Repair MOWING HEIGHT ADJUSTMENT See Figure 20. The mowing height adjustment can be changed by turning the cutting height adjustment handle. To Raise the Mower Deck: Turn the cutting height adjustment handle (A, Figure 20) clockwise. To Lower the Mower Deck: Turn the cutting height adjustment handle counter clock ...
-
Ferris Industries 5900972 - page 36
34 www.ferrisindustries.com Troubleshooting, Adjustment & Repair B A Figure 23. Lift Rod Clevis Adjustment A. Clevis, 1/2-20 B. 1/2-20 Jam Nut C. Cotter Pin D. Clevis Pin E. Rear Deck Lift Rod D C E DECK LEVELING ADJUSTMENT NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted. 1. Park machine on a flat ...
-
Ferris Industries 5900972 - page 37
35 Troubleshooting, Adjustment & Repair Figure 26. Deck Level Adjustment A. Jam nut B. Adjustment Bolt C. Chain Hanger Clevis A B C 6. Manually position the left hand mower blade so that the tip of the blade is pointing towards the front and back of the mower. Measure from the front tip of the blade on the cutting edge to the ground. Record thi ...
-
Ferris Industries 5900972 - page 38
4. Slide the drive belt over the edge of the stationary idler pulley (B). Carefully release the tension on the breaker bar until the idler arm comes to a stop. 6. Unhook the idler tension spring (C) from the anchor bolt (D). Remove the old belt and replace with a new one. Make sure the V-side of the belt runs in the pulley grooves. 7. Install the d ...
-
Ferris Industries 5900972 - page 39
TRANSMISSION DRIVE BELT REPLACEMENT 1. Remove the deck drive belt. See MOWER BELT REPLACEMENT sections. 2. Remove the clutch anchor bolts (A, Figure 30) that fasten the clutch anchor pad to the anchor. 3. Unplug the PTO clutch from the wire harness. 4. Remove the spring anchor nut (E) and remove the belt tension spring (D). 5. Drop the belt (H) fro ...
-
Ferris Industries 5900972 - page 40
38 www.ferrisindustries.com Troubleshooting, Adjustment & Repair TRANSMISSION NEUTRAL & TRACKING ADJUSTMENTS Neutral Adjustment 1. Park the machine on a smooth, level surface such as a concrete floor, away from bystanders and preferably facing a wall. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition ...
-
Ferris Industries 5900972 - page 41
39 Troubleshooting, Adjustment & Repair TRANSMISSION MAINTENANCE The hydrostatic transmissions are sealed units that require no maintenance other than the following. • Keep the machine and the transmission cooling fins clear or grass, leaves and debris. • Keep oil level in the reservoir (A, Figure 32) at the “FULL” line (B). Extra oil i ...
-
Ferris Industries 5900972 - page 42
40 www.ferrisindustries.com Troubleshooting, Adjustment & Repair BATTERY SERVICE Checking Battery Voltage A voltmeter can be used to determine condition of battery. When engine is off, the voltmeter shows battery voltage, which should be 12 volts. When engine is running, the voltmeter shows voltage of charging circuit which normally is 13 to 14 ...
-
Ferris Industries 5900972 - page 43
41 To Starter Switch Starting V ehicle Battery T o Ground To Starter Switch Dischar g ed V ehicle Battery Engine Block THIS HOOK-UP FOR NEGA TIVE GROUND VEHICLES MAKE CERT AIN VEHICLES DO NO T TOUCH Jumper Cab le Jumper Cab le WARNING Any procedure other than the preceding could result in: (1) personal injury caused by electrolyte squirting out the ...
-
Ferris Industries 5900972 - page 44
42 www.ferrisindustries.com Specifications SPECIFICATIONS NOTE: Specifications are correct at time of printing and are subject to change without notice. ENGINE: 19 Gross HP† Kawasaki Make Kawasaki Model FH580V Displacement 35.7 Cu. in (585 cc) Electrical System 12 Volt, 13 amp, Alternator, Battery: 340 CCA Oil Capacity 1.9 US qt. (1.8 L) w/ Filte ...
-
Ferris Industries 5900972 - page 45
THIS IS A 15 DEGREE SLOPE INSTRUCTIONS 1. Fold this page along the dotted line indicated above. 2. Align the left edge of this guide with a vertical tree , a power line pole, a fence post, or any vertical structure. 3. Compare the angle of the fold with the angle of the hill. SLOPE INDENTIFICA TION GUIDE ALIGN THIS EDGE WITH A VERTICAL SURF A CE (T ...
-
Ferris Industries 5900972 - page 46
Notes ...
-
Ferris Industries 5900972 - page 47
Thank you for purchasing Ferris commercial mowing equipment. Please take a few minutes to read this limited warranty information. It contains all the information you will need to have your Ferris mower repaired in the unlikely event that a breakdown covered by this limited warranty should occur. Owner’s Responsibilities - As a condition to our ob ...
-
Ferris Industries 5900972 - page 48
Comfort Control DD Series Walk-Behind Mowers OPERATOR’S MANUAL ...
Haben Sie eine Frage bezüglich Ferris Industries 5900972?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ferris Industries 5900972 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ferris Industries 5900972 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.