Deutsch dropdown-ico

Bedienungsanleitung Cisco Systems WS-SVC-CMM

36 Seiten 0.9 mb
Download

Zur Seite of 36

Summary
  • Cisco Systems WS-SVC-CMM - page 1

    Corporate Headquarters: Copyright © 20 0 1–20 05 Cisco Systems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Catalyst 6500 Series Switch and Cisco 7600 Series Router CM M Installation and Verification Note Product Number: WS-SVC-CMM This publication contains the procedures for installing and c ...

  • Cisco Systems WS-SVC-CMM - page 2

    2 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Contents Contents This publication contains these sections: • Front Panel Descriptions, page 2 • Requirements, page 6 • Safety Overvie w , page 7 • Required T ools, page 9 • Installing and Removing the CMM, page 9 • Removing and ...

  • Cisco Systems WS-SVC-CMM - page 3

    3 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Front Panel Descriptions • Port adapter slots— Figure 1 sho ws the E1 port adapter in the left and middle slots, with a blank f iller plate in the right slot. • REAR MODULE ST A TUS LED— T able 2 describes the REAR MODULE ST A TUS L ...

  • Cisco Systems WS-SVC-CMM - page 4

    4 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Front Panel Descriptions 6-Port T1 and E1 Port Adapters The front panel features of the 6-port T1 and E1 port adapters are as follows: • Receiv e port LEDs—The LEDs on the front panel indicate the status of each T1 and E1 interface. T a ...

  • Cisco Systems WS-SVC-CMM - page 5

    5 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Front Panel Descriptions 24-Port FXS Port Adapter The front panel features of the 24-port FXS port adapter are as follows: • Recei ve port LEDs—The LEDs on the front panel indicate the status of each FXS interface. T able 4 describes th ...

  • Cisco Systems WS-SVC-CMM - page 6

    6 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Requirements Figur e 4 Ad-hoc Conf erencing and T r anscoding Por t Adapt er Fr ont Panel F eatur es Requirements These sections describe the hardware and software requirements: • Hardware Requirements, page 6 • Software Requirements, p ...

  • Cisco Systems WS-SVC-CMM - page 7

    7 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Safety Overview Software Requirements For software requirements, refer to the Release Notes for the Cisco Catalyst 6500 Series and the Cisco 7600 Series Communication Media Module at this URL: http://www .cisco.com/univ ercd/cc/td/doc/produ ...

  • Cisco Systems WS-SVC-CMM - page 8

    8 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Safety Overview Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other ...

  • Cisco Systems WS-SVC-CMM - page 9

    9 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Required Tools Required Tools Warning Only trained and qualif ied personnel should be allowed to install, replace, or service this equipment. Statement 1030 These tools are required to remov e and replace the CMM and port adapters: • Flat ...

  • Cisco Systems WS-SVC-CMM - page 10

    10 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM T o install the CMM into the Catalyst 6500 series switch or the Cisco 7600 series router , perform these steps: Step 1 Make sure that you take the necessary precautions to pre vent ESD damage. Step 2 Choose ...

  • Cisco Systems WS-SVC-CMM - page 11

    11 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM Figur e 5 P ositioning the Module in a Hor izontal Slot Chassis 58569 INPUT OK FAN OK OUTPUT FAIL o INPUT OK FAN OK OUTPUT FAIL o 1 2 3 FAN STA TUS 4 5 6 SUPERVISOR2 WS-X6K-SUP2-2GE STATUS SYSTEM CONSOLE PWR ...

  • Cisco Systems WS-SVC-CMM - page 12

    12 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM Figur e 6 Clear ing the EMI Gasket in a Hor izontal Slot Chassis b. Using the thumb and foref inger of each hand, grasp the two ejector lev ers and press down to create a small (0.040 inch [1 mm]) gap betwee ...

  • Cisco Systems WS-SVC-CMM - page 13

    13 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM Figur e 7 Ejector Lev er Closure in a Hor izontal Slot Chassis Note Failure to fully seat the module in the backplane connector can result in error messages. d. T ighten the two capti ve installation screws ...

  • Cisco Systems WS-SVC-CMM - page 14

    14 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM Figur e 8 P ositioning the Module in a V er tical Slot Chassis b. Carefully slide the module into the slot until the EMI gasket along the right edge of the module makes contact with the module in the slot ad ...

  • Cisco Systems WS-SVC-CMM - page 15

    15 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM Figur e 9 Clear ing the EMI Gasket in a V ertical Slot Chassis Caution Exerting too much pressure on the ejector le vers will bend and damage them. d. While pressing on the ejector lev ers, simultaneously cl ...

  • Cisco Systems WS-SVC-CMM - page 16

    16 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM Figur e 1 0 Ejector Lev er Closure in a V ertical Slot Chassis e. T ighten the two capti ve installation screws on the module. Note Make sure that the ejector le vers are fully closed before tightening the c ...

  • Cisco Systems WS-SVC-CMM - page 17

    17 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Installing and Removing the CMM T o remo ve a module from the chassis, perform these steps: Step 1 Disconnect any network interf ace cables that are attached to the module. Step 2 V erify that the captiv e installation screws on all of the ...

  • Cisco Systems WS-SVC-CMM - page 18

    18 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Removing and Replacing Port Adapters Removing and Replacing Port Adapters Follo w the procedures in this section to remove and replace the port adapters on the CMM: • Removing a Port Adapter from CMM Slots 1 through 3, page 18 • Instal ...

  • Cisco Systems WS-SVC-CMM - page 19

    19 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Removing and Replacing Port Adapters Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) th ...

  • Cisco Systems WS-SVC-CMM - page 20

    20 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Removing and Replacing Port Adapters Figur e 12 CMM (T op View with P ort Adapt ers Installed) Figur e 13 CMM (T op View with P ort Adapt ers Remov ed) 68453 AVVID Services Module STA TUS WS-X6600 Standoffs (6) Phillips screws (6) WS-X6600 ...

  • Cisco Systems WS-SVC-CMM - page 21

    21 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Removing and Replacing Port Adapters Installing a Port Adapter in CMM Slots 1 through 3 Note When you face the CMM front panel, slot 1 is on the left, slot 2 is in the middle, and slot 3 is on the right. Slot 4 is located internally . (See ...

  • Cisco Systems WS-SVC-CMM - page 22

    22 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Removing and Replacing Port Adapters Caution Using the screws or standof fs to seat the port adapter could warp the port adapter . Befor e you install and tighten the securing screws, ensure that the port adapter is fully seated by visuall ...

  • Cisco Systems WS-SVC-CMM - page 23

    23 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Removing and Replacing Port Adapters Step 4 In Figure 13 , note the location of the two slot 4 standof f mounting posts. Remove the tw o mounting posts that secure the port adapter . Step 5 In Figure 13 , note the location of the two slot ...

  • Cisco Systems WS-SVC-CMM - page 24

    24 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Verifying the Installation Caution Using the screws or standof fs to seat the port adapter could warp the port adapter . Before you install and tighten the securing screws, ensure that the port adapter is fully seated by visually v erifyin ...

  • Cisco Systems WS-SVC-CMM - page 25

    25 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 RJ-45 Port Connector and Cabling Specifications Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. T o avoid electric shock, use caution when working near WAN ports. When detac ...

  • Cisco Systems WS-SVC-CMM - page 26

    26 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 RJ-21 Port Connector and Cabling Specifications RJ-21 Port Connector and Cabling Specifications Caution Do not connect the WS-SVC-CMM-24 FXS port adapter directly to a voicemail serv er , IVR application, or fax serv er if the servers hav ...

  • Cisco Systems WS-SVC-CMM - page 27

    27 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Accessing the Port Adapter Ports Accessing the Port Adapter Ports From the CMM command-line interface (CLI), you identify each port adapter by interface_name follo wed by slot_num / port_num . For example, to conf igure the f irst port on ...

  • Cisco Systems WS-SVC-CMM - page 28

    28 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Configuring the Port Adapter Ports Configuring the Port Adapter Ports Conf iguring the CMM interfaces is similar to conf iguring the voice interfaces on other Cisco products. CMM interface conf iguration requirements are dependent on your ...

  • Cisco Systems WS-SVC-CMM - page 29

    29 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Disaster Recovery for CMM Software Upgrades Disaster Recovery for CMM Software Upgrades Note Disaster recov ery is supported only on systems that are using Catalyst operating system software on the supervisor engine. This section describes ...

  • Cisco Systems WS-SVC-CMM - page 30

    30 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Disaster Recovery for CMM Software Upgrades Step 5 Enter the set poll disable command to disable polling. Step 6 Enter the set module power up mod command to power up the CMM. When the CMM po wers up, disaster recovery is complete. Step 7 ...

  • Cisco Systems WS-SVC-CMM - page 31

    31 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Regulatory Standards Compliance Step 7 After you complete the disaster recov ery , enter the clear f ilename-alias disk0:ws-svc-cmm command to terminate the f ilename translation. Step 8 After you complete the disaster recov ery , set the ...

  • Cisco Systems WS-SVC-CMM - page 32

    32 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Obtaining Documentation Obtaining Documentation Cisco documentation and additional literature are av ailable on Cisco.com. Cisco also provides se veral ways to obtain technical assistance and other technical resources. These sections e xpl ...

  • Cisco Systems WS-SVC-CMM - page 33

    33 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Documentation Feedback Documentation Feedback Y ou can send comments about technical documentation to bug-doc@cisco.com. Y ou can submit comments by using the response card (if present) behind the front cov er of your document or by writin ...

  • Cisco Systems WS-SVC-CMM - page 34

    34 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Obtaining Technical Assistance In an emergenc y , you can also reach PSIR T by telephone: • 1 877 228-7302 • 1 408 525-6532 Obtaining Technical Assistance For all customers, partners, resellers, and distrib utors who hold valid Cisco s ...

  • Cisco Systems WS-SVC-CMM - page 35

    35 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Obtaining Additional Publications and Information T o open a service request by telephone, use one of the follo wing numbers: Asia-Pacif ic: +61 2 8446 7411 (Australia: 1 800 805 227) EMEA: +32 2 704 55 55 USA: 1 800 553-2447 For a complet ...

  • Cisco Systems WS-SVC-CMM - page 36

    36 Catalyst 6500 Series Switch and Cisco 7600 Series Router CMM Installation and Verification Note 78-14107-07 Obtaining Additional Publications and Information • iQ Magazine is the quarterly publication from Cisco Systems designed to help gro wing companies learn how the y can use technology to increase rev enue, streamline their business, and e ...

Produzent Cisco Systems Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Cisco Systems WS-SVC-CMM erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco Systems
- Bedienungsanleitungen WS-SVC-CMM
- Produktkarten Cisco Systems
- Informationsbroschüren
- oder Energieetiketten Cisco Systems WS-SVC-CMM
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Systems WS-SVC-CMM.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Systems WS-SVC-CMM, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Systems WS-SVC-CMM. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Systems WS-SVC-CMM ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Systems WS-SVC-CMM, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Systems WS-SVC-CMM hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Systems WS-SVC-CMM verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Systems WS-SVC-CMM bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Systems WS-SVC-CMM befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Systems WS-SVC-CMM, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Systems WS-SVC-CMM - die uns die ersten Schritte während der Nutzung von Cisco Systems WS-SVC-CMM erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Systems WS-SVC-CMM hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Systems WS-SVC-CMM im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Systems WS-SVC-CMM?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Systems WS-SVC-CMM nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Systems WS-SVC-CMM hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)