-
Pelco ES31C - page 1
ES30C/ES31C Series Esprit ® with IOP C309M-J (9/04) ® OPERA TION/PROGRAMMING ...
-
Pelco ES31C - page 2
2 C309M-J (9/04) ...
-
Pelco ES31C - page 3
C309M-J (9/04) 3 CONTENTS Section Page IMPORT ANT SAFETY INSTRUCTIONS .................................................................................................. ............................................................................. 5 OPERA TION .......................................................................................... ...
-
Pelco ES31C - page 4
4 C309M-J (9/04) WHITE BALANCE .................................................................................................................. .................................................................................... 40 WIPER MODE ......................................................................................................... ...
-
Pelco ES31C - page 5
C309M-J (9/04) 5 IMPORT ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...
-
Pelco ES31C - page 6
6 C309M-J (9/04) OPERA TION POWER-UP DISPLA Y When the system is powered up, the selected protocol, revision number , and other information is displayed on the monitor . For e xample, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power - up mode. ( ...
-
Pelco ES31C - page 7
C309M-J (9/04) 7 OPERA TING NOTES ENVIRONMENT AL RANGE The operating temperature ranges from a minimum of -50 ° F (-45 ° C) to a maximum of 122 ° F (50 ° C) for sustained system operation or 140 ° F (60 ° C) absolute maximum. The entire unit can de-ice and be operational in two hours from a temperature of -13 ° F (-25 ° C). The thermostatic ...
-
Pelco ES31C - page 8
8 C309M-J (9/04) PA TTERNS The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens command. Presets, flip, digital zoom, proportional pan, and turbo are not allowed in a pattern. Zones can be enabled while running a ...
-
Pelco ES31C - page 9
C309M-J (9/04) 9 PROGRAMMING - ES30C16/ES31C16 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sync Menu Power Up Default Exit Power -Up Menu Wiper Mode Momentary Wiper Dwell <s> 2 Wiper T ime <m> 60 Exit *Wiper Menu Limit Stops Off Set Man ...
-
Pelco ES31C - page 10
10 C309M-J (9/04) PROGRAMMING - ES30C22/ES31C22 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sync Menu Power Up Default Exit Power -Up Menu Wiper Mode Momentary Wiper Dwell <s> 2 Wiper T ime <m> 60 Exit *Wiper Menu Limit Stops Off Set Ma ...
-
Pelco ES31C - page 11
C309M-J (9/04) 11 PROGRAMMING - ES30CBW18/ES31CBW18 Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sync Menu Power Up Default Exit Power -Up Menu Wiper Mode Momentary Wiper Dwell <s> 2 Wiper T ime <m> 60 Exit *Wiper Menu Limit Stops Off Set ...
-
Pelco ES31C - page 12
12 C309M-J (9/04) PROGRAMMING ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’ s controllers varies according to the type of controller you are using. Instructions for progra mming preset 95 are given below for ...
-
Pelco ES31C - page 13
C309M-J (9/04) 13 AUTO FOCUS MODE There are two auto focus modes: Auto – If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode. The system will return to auto focus if you pan or tilt the unit or do a zoom function. Off – If the mode is set to off, the system will operate in the m ...
-
Pelco ES31C - page 14
14 C309M-J (9/04) AUTO IRIS The following are the settings for auto iris: Mode Level Peak To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the cursor (>) beside Auto Iris. 5. Press the Iris Open ...
-
Pelco ES31C - page 15
C309M-J (9/04) 15 AUTO IR LEVEL (MODELS ES30CBW18/ES31CBW18 ONL Y) The auto IR level is the light level at which the infrared filter switches IN or OUT . Following are the available settings for the Auto IR Level: DUSK (default) – approximately 6 lux (black-white) approximately 13 lux (color) DARK – approximately 0.1 lux (black-white) approxima ...
-
Pelco ES31C - page 16
16 C309M-J (9/04) AUTO SHARPNESS The following settings are available for auto sharpness: On – Automatically sets the sharpness of the camera. Off – The sharpness of the camera needs to be manually set (refer to Sharpness ). To change the mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Pre ...
-
Pelco ES31C - page 17
C309M-J (9/04) 17 AZ/EL Az/El programs the horizontal display position of the Azimuth 1 /Elevation 2 label. NOTE: Az/El display is not available while you are programming or running a pattern. The following settings are available for the Az/El label: Off – Label is not displayed. Left (default) – Label is displayed on the left-hand side of the ...
-
Pelco ES31C - page 18
18 C309M-J (9/04) AZ/EL LINE Az/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE: Az/El display is not available while you are pr ...
-
Pelco ES31C - page 19
C309M-J (9/04) 19 AZIMUTH ZERO Azimuth is the pan angle from 0 ° to 359 ° . Azimuth zero is the programmed 0 ° point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point. To set azimuth zero: 1. Program preset 95 (28). The main menu appears. 2. Posi ...
-
Pelco ES31C - page 20
20 C309M-J (9/04) BACKLIGHT COMPENSA TION There are two backlight compensation modes: On – The system uses the center 10 percent of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed. NOTE: E ...
-
Pelco ES31C - page 21
C309M-J (9/04) 21 DIRECTION Direction programs the horizontal display position of the Direction label (N, NW , NE, …). NOTE: For direction to be accurate, the azimuth zero must be set to magnetic north. NOTE: Direction display is not available while you are programmming or running a pattern. The following settings are available for the Direction ...
-
Pelco ES31C - page 22
22 C309M-J (9/04) DIRECTION LINE Direction Line controls the vertical display position of the Direction label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE: Direction display is not available while you ar ...
-
Pelco ES31C - page 23
C309M-J (9/04) 23 DISPLA Y DURA TION Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor . The available settings for display duration include the following: CONST ANT - The label is displayed continuously . 2 SECONDS (default) - The label is displayed for 2 seconds after PTZ functions end. 5 SE ...
-
Pelco ES31C - page 24
24 C309M-J (9/04) GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase the noise level of the picture. To change the gain: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter ...
-
Pelco ES31C - page 25
C309M-J (9/04) 25 IR FIL TER MODE (MODELS ES30CBW18/ES31CBW18 ONL Y) There are two settings for the IR filter mode: Auto – IR filter switches in and out automatically . IMPORT ANT : Automatic shutter speed must be set to Auto for the IR filter to operate automatically . If the automatic shutter speed is disabled, the IR filter setting will automa ...
-
Pelco ES31C - page 26
26 C309M-J (9/04) LIMIT STOPS NOTE: Limit stops are inactive while setting items in the program menu (e.g. azimuth zero, scan limits, manual pan limits). TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to ent ...
-
Pelco ES31C - page 27
C309M-J (9/04) 27 LIMIT STOPS MENU The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu. 4. Move the cursor to Set Man Limits and press the Iris Open button. PRE ...
-
Pelco ES31C - page 28
28 C309M-J (9/04) Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached. The manual scan limit stops can be set in one of two ways: At the controller by programming presets 92 and 93 or At the controller by programming the Limit Stops menu PRESETS Refe ...
-
Pelco ES31C - page 29
C309M-J (9/04) 29 LINE SYNCHRONIZA TION If cameras are out of phase with each other , they may produce what appears to be vertical roll when switching between cameras. There are two settings for line synchronization: On – Adjust the synchronization of the power line voltage so that it is in phase with other cameras. Off – The system synchronize ...
-
Pelco ES31C - page 30
30 C309M-J (9/04) LOWLIGHT LIMIT (MODELS ES30C22/ES31C22 AND ES30CBW18/ES31CBW18 ONL Y) This setting determines the maximum length of time the shutter will remain open automatically in low light conditions. There are six choices: 2 = 1/2 second 8 = 1/8 second 30 = 1/30 second 4 = 1/4 second 15 = 1/15 second 60 = 1/60 second NOTE: LOWLIGHT does not ...
-
Pelco ES31C - page 31
C309M-J (9/04) 31 P ARK TIME MINUTES This feature causes the system to park at preset 1 after a programmed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature. NOTE: Preset 1 must be programmed for the dome to park. To change the park time: 1. P ...
-
Pelco ES31C - page 32
32 C309M-J (9/04) PA TTERN LENGTH The Esprit can do the following: One full pattern - 1.5, 3, or 6 minutes long or T wo half patterns - .75, 1.5, or 3 minutes long This pattern can consist of any standard pan, tilt, or lens command. Presets, flip, and turbo are not allowed in a pattern. Zone scan can be enabled while running a pattern. NOTE: Digita ...
-
Pelco ES31C - page 33
C309M-J (9/04) 33 POWER-UP MODE This feature lets the dome resume a desired condition following power -up. The menu includes the following choices. • Default – On power -up, the system goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen. • Park – The syst ...
-
Pelco ES31C - page 34
34 C309M-J (9/04) PROPORTIONAL P AN There are two proportional pan modes: On – Enables the proportional pan mode. The amount of zoom controls the pan and tilt. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings. This keeps the image from moving too fast on the mo ...
-
Pelco ES31C - page 35
C309M-J (9/04) 35 RESET CAMERA Default Setting <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Other> Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Resetting the camera returns the settings to their defaults. Models Models Models ES30 ...
-
Pelco ES31C - page 36
36 C309M-J (9/04) SCAN SPEED The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. To change the scan speed: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other . 3. Press the Iris Open button to enter the menu entitled Other . 4. Position t ...
-
Pelco ES31C - page 37
C309M-J (9/04) 37 SHARPNESS Use the Sharpness setting to manually set the sharpness of the camera. To manually set the sharpness of the camera: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the cursor (>) beside Next. Press the Ir ...
-
Pelco ES31C - page 38
38 C309M-J (9/04) SHUTTER SPEED There are several electronic shutter speed settings: Auto 1/2 1/4 1/8 1/15 1/30 1/60 1/120 1/180 1/250 1/500 1/1000 1/2000 1/4000 1/10,000 1/30,000 In the Auto setting the camera controls the shutter speed automatically . Increasing the shutter speed lowers the light sensitiv ity , but rapidly moving objects will be ...
-
Pelco ES31C - page 39
C309M-J (9/04) 39 SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the Esprit system. Y ou can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second. The difference will be in the turbo ...
-
Pelco ES31C - page 40
40 C309M-J (9/04) WHITE BALANCE The settings for white balance are as follows: Auto white bal R Gain B Gain To change the white balance settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the cursor (>) beside Next. 5. Press t ...
-
Pelco ES31C - page 41
C309M-J (9/04) 41 WIPER MODE There are three wiper settings: Wiper Mode Wiper Dwell Wiper T ime To change the wiper settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Wiper . 3. Press the Iris Open button to enter the Wiper menu. 4. Move the joystick up or down to position the cursor next to one of the ...
-
Pelco ES31C - page 42
42 C309M-J (9/04) The Esprit system features onscreen programmable zone blanking. This feature lets you define any zone as blanked for video (viewing/ recording). Zones can be programmed to overlap each other , although this is not recommended. If you program two zones to overlap, the title of the zone with the highest priority (zone 8 is the highe ...
-
Pelco ES31C - page 43
C309M-J (9/04) 43 ZOOM Zoom programs the horizontal display position of the Zoom label. The following settings are available for the Zoom label: Off – Label is not displayed. Left – Label is displayed on the left-hand side of the screen. Center (default) – Label is displayed in the center of the screen. Right – Label is displayed on the rig ...
-
Pelco ES31C - page 44
44 C309M-J (9/04) ZOOM LIMIT ES30C16/ES31C16 - 16X optical zoom and 10X electronic zoom, can be set for 16X, 32X, 64X, 128X, or 160X. ES30C22/ES31C22 - 22X optical zoom and 10X electronic zoom, can be set for 22X, 32X, 88X, 176X, or 220X. ES30CBW18/ES31CBW18 - 23X optical zoom and 10X electronic zoom, can be set for 23X, 32X, 92X, 184X or 230X. To ...
-
Pelco ES31C - page 45
C309M-J (9/04) 45 ZOOM LINE Zoom Line controls the vertical display position of the Zoom label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE: Zoom display is not available while you are programming or run ...
-
Pelco ES31C - page 46
46 C309M-J (9/04) SPECIFICA TIONS ELECTRICAL Input V oltage: 24, 120, or 230 V AC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset featur e enabled when power becomes unstable or interrupted. Power Requirements: Maximum power consumption is 70 V A per system Heater and Defroster: Thermostatically controlled heater consumes 10 watts and cy ...
-
Pelco ES31C - page 47
C309M-J (9/04) 47 Sensitivity ES30C16/ES31C16: 0.05 lux at 1/2-second shutter speed (NTSC) 0.05 lux at 1/1.5-second shutter speed (P AL) ES30C22/ES31C22: 0.02 lux at 1/2-second shutter speed (NTSC) 0.02 lux at 1/1.5-second shutter speed (P AL) ES30CBW18/ES31CBW18: 0.08 lux at 1/2-second shutter speed (color , NTSC/P AL) 0.3 lux at 1/1.5-second shut ...
-
Pelco ES31C - page 48
...
-
Pelco ES31C - page 49
REVISION HISTORY Manual # Date Comments C309M 9/00 Original version. C309M-A 12/00 Added information on “Pan Limit” message per ECO #00-6635. C309M-B 6/01 Added information on zone blanking. C309M-C 9/02 Camera modifications. C309M-D 6/03 Added Az/El/Direction menu per ECO #03-8861. Updated layout. C309M-E 8/03 Revised per ECO #03-9210 for new ...
-
Pelco ES31C - page 50
W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 ® United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...
Haben Sie eine Frage bezüglich Pelco ES31C?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco ES31C nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco ES31C hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.