Bedienungsanleitung MTD 31AS2B5

13 Seiten 3.33 mb
Download

Zur Seite of 13

Summary
  • MTD 31AS2B5 - page 1

    Ser vice Manual MTD Products LLC - Product T r aining and Education Dep artment FORM NUMBER 769-01416 9/2004 31AS2B5 Snow Thrower IMAGE SHO W S Y ARD-MAN UNIT NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power  equipment of the kind described in this publication, and are not in ...

  • MTD 31AS2B5 - page 2

    ...

  • MTD 31AS2B5 - page 3

    TABLE OF CONTENTS General Information ........ ................................................. ................ ............... ........... 1 Controls ............ ................................................. .............................. ............... ........... 1 Auger ........... ................................. ..................... ...

  • MTD 31AS2B5 - page 4

    ...

  • MTD 31AS2B5 - page 5

    1 31AS2B5-71 1 Snow Thrower Model Number #31AS2B5- 7 1 1 Seria l Number 1E074B20005 NOTE: The equipment that was used to write this section w as a prot otype an d was witho ut labels. There may be subtle dif ferences between prototypes and productio n equipment but the disassembly procedures preformed will remain the same. GENERAL INFORMATION T ecu ...

  • MTD 31AS2B5 - page 6

    2 switch and the A.C. plug connector with st arter button that is used for the electric start. See Figure 3. 4. BACK OF UNIT The Model tag is located on the back of the unit and includes phone numbers for customer assistance : T roy- Bilt 330-558-552 0 or 1-800-52 0-5520. The choke control is shown on the right side of the carburetor cover . T o th ...

  • MTD 31AS2B5 - page 7

    3 7. DISCHARGE CHUTE The mitten grip handle on the sno w chute allows easy adjustment side to side. See Figure 7. 8. AUGER DRIVE BELT REPLACEMENT 8.1. Remove the five (5) screws on the per imeter of the belt cov er using a 3 /8" socke t with shor t extension and ratchet. See Figure 8. 8.2. With t he cover re moved insp ect for wear on the belt ...

  • MTD 31AS2B5 - page 8

    4 engine pulley . Rep lace by using th e same proc e- dure. See Figure 1 1. 9. AUGER REMOVAL 9.1. Place a two by four wedge in the housing to hold the auger from turning. Using 1” socket, remove the auger pulley nut. The shaf t is reverse threaded an d the nut is removed by turning it clockwise. See Figure 12. NOTE: During reassembly place the 2X ...

  • MTD 31AS2B5 - page 9

    5 9.4. Remove and inspect the bearing and heavy washer for ear or damage. See Fig ure 15. 9.5. Facing the housing, slide the auger assembly to the right, and then r emove the auger and shaft assembly from the housing. See Figure 16 . Figure 15 Bearing and Washer Figure 16 Slide auger asse mbly to the righ t 9.6. Inspect the auger assembly for wea r ...

  • MTD 31AS2B5 - page 10

    6 1 1. FRONT SHROUD COVER REMOVAL 1 1.1. Remove the three screws from the inside to p of the auger housing using a 3/8" socket and ratchet. See Figure 19. 1 1.2. Remove the remaining five ( 5 ) perimeter screws and two ( 2 ) scr ews holding t he starter plug assemb ly using a 5/ 16" socket . The shr oud is slotted to allow the rem oval fr ...

  • MTD 31AS2B5 - page 11

    7 bling easier to leave the lower chute att ached and remove the deflector . See Figure 23. 1 1.6. Remove the gas cap and the o il dipstick and then lif t of f the shroud . With the Shroud removed you now have complete access to the engine, sta rter , fuel tank and all related items for servicing or replaceme nt. See Figure 24. Figure 23 Figure 24 ...

  • MTD 31AS2B5 - page 12

    8 NOTE: During reassembly , align the chute assembly by facing it to wards the pla stic retain- ing ring. Be sure the chute is positioned all the way to the right or left upo n re-assembly . See Figure 27. Check that the upper and lower flan ges lock into the retaining ring and that the latch closes and locks prop- erly . See Figure 28. 12. ENGINE ...

  • MTD 31AS2B5 - page 13

    9 13. GAS T ANK 13.1. A wire retainer holds the gas tank. The t ank can easily be replaced by pus hing the wire out of the lower support pla te at the bend on the side of the tank. See Figure 30. NOTE: The ga s line clamp is accessible below the mounting br acket. Figure 30 Press DOWN here Gas Line Clamp ...

Produzent MTD Kategorie Snow Blower

Dokumente, die wir vom Produzenten des Geräts MTD 31AS2B5 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen MTD
- Bedienungsanleitungen 31AS2B5
- Produktkarten MTD
- Informationsbroschüren
- oder Energieetiketten MTD 31AS2B5
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung MTD 31AS2B5.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen MTD 31AS2B5, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen MTD 31AS2B5. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts MTD 31AS2B5 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts MTD 31AS2B5, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von MTD 31AS2B5 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von MTD 31AS2B5 verständlich ist.

Eine gänzliche Bedienungsanleitung von MTD sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von MTD 31AS2B5 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von MTD 31AS2B5 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich MTD 31AS2B5, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts MTD 31AS2B5 - die uns die ersten Schritte während der Nutzung von MTD 31AS2B5 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit MTD 31AS2B5 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von MTD 31AS2B5 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich MTD 31AS2B5?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit MTD 31AS2B5 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit MTD 31AS2B5 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)