Bedienungsanleitung Sharp TL-M5200

41 Seiten 1.05 mb
Download

Zur Seite of 41

Summary
  • Sharp TL-M5200 - page 1

    MODEL TL-M5200 TL-M4600 LCD MONIT OR RS-232C Specifications and Commands .......... 2 Setting up the Monitor Network En vir onment .... 10 1. Connecting the Monitor to a Computer ............ 1 1 2. Setting an IP Address for the Computer .......... 12 3. Setting up a Network Connection for the Monitor .... 14 Controlling the Monitor via LAN ....... ...

  • Sharp TL-M5200 - page 2

    -2 Computer contr ol A computer can be used to control the monitor by connecting an RS-232C serial control cable (cross type, commerciall y available) to the monitor . (See page 20 of the monitor’ s operation manual f or connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: C ...

  • Sharp TL-M5200 - page 3

    -3 Commands Example: When turning on the monitor , make the follo wing setting. → ← PO W R _ 1 __ OK Monitor Computer Normal(Computer) Full Dot By Dot(Computer) / Normal(Video) S.Stretch(Video) Cinema16:9(Video) Cinema14:9(Video) Zoom14:9(Video) CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN Power Monitor Condi ...

  • Sharp TL-M5200 - page 4

    -4 RS-232C Specifications and Commands Normal (Computer) Full Dot By Dot(Computer) / Normal(Video) S.Stretch(Video) Cinema16:9(Video) Cinema14:9(Video) Zoom14:9(Video) Normal(Computer) Full Dot By Dot(Computer) / Normal(Video) S.Stretch(Video) Cinema16:9(Video) Cinema14:9(Video) Zoom14:9(Video) Normal(Computer) Full Dot By Dot(Computer) / Normal(Vi ...

  • Sharp TL-M5200 - page 5

    -5 RS-232C Specifications and Commands Standard Presentation Movie Game sRGB Off On On(Display) -16 – +16 0 – +40 -30 – +30 -30 – +30 -30 – +30 -10 – +10 -30 – +30 -30 – +30 -30 – +30 -2 – +2 Off Level 1 Level 2 Off On Off On Off On Auto RGB Component Standard Presentation Movie Game sRGB Off On On(Display) -16 – +16 0 – +40 ...

  • Sharp TL-M5200 - page 6

    -6 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN HDMI INPUT S-VIDEO INPUT AV Mode OPC Backlight Contrast Bright Color Tint Sharpness Red Green Blue Color Temp DNR Film Mode Black Monochrome Adjustment Reset Signal Type Dynamic Range Color Space AV Mode OPC Backlight Contrast Bri ...

  • Sharp TL-M5200 - page 7

    -7 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN VIDEO INPUT Position Fine Sync RGB Frequency Check HDMI Setup Audio Audio Out Standby Mode Auto Restart Power Management No Operation Off Ecology Closed Caption AV Mode OPC Backlight Contrast Bright Color Tint Sharpness Red Green ...

  • Sharp TL-M5200 - page 8

    -8 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN Video System Background Selection LED Power On Delay Picture Flip Keylock Set Inputs Input Label Language Master& Slave P&P (Split-screen) AUTO PAL SECAM NTSC4.43 NTSC3.58 PAL_60 Blue None Off On Delay Time 0 – 100 Sec. ...

  • Sharp TL-M5200 - page 9

    -9 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN P&P Main Select ALL Reset Sleep Timer Multi Screen *3 Left *2 Right *2 Sleep Timer Status Screen Position H-Bezel V-Bezel H-Position V-Position ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ER ...

  • Sharp TL-M5200 - page 10

    -10 Pag e 1 1 1. Connecting the monitor to a computer Setting up the Monitor Network Environment This section describes the basic procedure for using the monitor via the network. If the network is alread y constructed, the monitor’ s network settings may need to be c hang ed. Please con- sult your network administrator for assistance with these s ...

  • Sharp TL-M5200 - page 11

    -11 Setting up the Monitor Network Environment 1. Connecting the Moni- tor to a Computer Establishing a one-to-one connection from the monitor to a computer . Using a LAN cable (Cat- egory 5, cross-over type) you can configure the monitor via the computer . 1 Disconnect the computer’ s LAN cable fr om the existing netw ork. 2 Connect a LAN cable ...

  • Sharp TL-M5200 - page 12

    -12 1 2 1 XXXXXXXXX 1 2 Setting up the Monitor Network Environment 2. Setting an IP Address for the Computer The following describes how to make settings in Windo ws Vista ® . 1 Log on the network using the administrator’ s account for the computer . 2 Click “s tart”, and click “Control Panel”. 3 Click “View netw ork status and tasks? ...

  • Sharp TL-M5200 - page 13

    -13 Setting up the Monitor Network Environment 1 2 5 Click “Internet Protocol V ersion 4 (TCP/IPv4)”, and click the “Properties” button. 6 Confirm or change an IP address f or the setup computer . 1 Confirm and note the current IP ad- dress, Subnet mask and Default gatewa y . Make sure to note the current IP ad- dress, Subnet mask and Defau ...

  • Sharp TL-M5200 - page 14

    -14 Setting up the Monitor Network Environment 3. Setting up a Network Connection for the Monitor Settings for suc h items as the monitor’ s IP ad- dress and subnet mask are compatible with the existing network. Set each item on the monitor as follows. (See page 38 of the monitor’ s operation manual for setting.) DHCP Client : OFF IP Address : ...

  • Sharp TL-M5200 - page 15

    -15 4 The TCP/IP setting screen ap- pears, ready for network settings f or the monitor . Note • Confirm the existing network’ s segment (IP address group) to avoid setting an IP ad- dress that duplicates the IP addresses of other network equipment or computers. If “192.168.150.2” is not used in the network having an IP address of “192.168 ...

  • Sharp TL-M5200 - page 16

    -16 Controlling the Monitor via LAN Controlling the Monitor Using Internet Explorer (Version 5.0 o r later) Complete connections to external equipment before starting the operation. (See pages 16- 20 of the monitor’ s operation manual.) Complete the A C cord connection. (See pag e 21 of the monitor’ s operation manual.) 1 Start Internet Explore ...

  • Sharp TL-M5200 - page 17

    -17 Confirming the Monitor Status (Status) On this screen, you can confirm the monitor status. Y ou can confirm the follo wing items : • • • • • MA C Address • • • • • Power • • • • • Condition • • • • • Input • • • • • Signal Info • • • • • S erial Number Note • If you clic k the “Ref ...

  • Sharp TL-M5200 - page 18

    -18 Controlling the Monitor via LAN Setting and Adjusting the Monitor (Settings & Adjustments ) Example: “Picture” screen display for COMPUTER On these screens, you can make monitor set- tings or adjust ments. Y ou can set or adjust the following items : Note • If you click the “Refresh” button before the screen is displa yed complete ...

  • Sharp TL-M5200 - page 19

    -19 Controlling the Monitor via LAN Making General Settings for the Network (Network - General) On this screen, you can make general settings relating to the network. After clic king the “Apply” button, the set val- ues appear . Confirm that the v alues are set properl y , and then c lick the “Confirm” but- ton. Note • After setting items ...

  • Sharp TL-M5200 - page 20

    -20 Controlling the Monitor via LAN Set ting Error Items and Destination Addresses to which E - m ail is to be Sent when an Error Occurs (Mail – Recipient Settings) On this screen, you can input e-mail destina- tions to which err or notification (error items) e-mails are sent. Note • E-mail Address can be up to 64 characters. • Y ou can input ...

  • Sharp TL-M5200 - page 21

    -21 Setting up the Monitor Using RS-232C or T elnet When Connecting Using RS-232C 1 Launch general purpose terminal emulator . 2 Input settings for the RS-232C port of the terminal em ulator as follows. Baud Rate : 9600 bps* Data Length : 8 bit Parity Bit : None Stop Bit : 1 bit Flow Control : None * This is the f actor y default setting. If the va ...

  • Sharp TL-M5200 - page 22

    -22 When Connecting Using Telnet 1 Click “Star t” from the Windows ® desk- top and select “Run”. 2 Enter “telnet 192.168.150.2” in the text box that opens up. (If the IP address of the monitor i s 192.168.150.2.) 3 Click the “OK” button. 4 “User Name:” is displayed. Input the user name and press the “Enter” key . • If a u ...

  • Sharp TL-M5200 - page 23

    -23 SETUP MENU (Main Menu) [1] IP Address IP address settings. (P age 26 ) [2] Subnet Mask Subnet mask settings. (P age 26 ) [3] Default Gateway Def ault gatewa y settings. (Page 26 ) [4] User Name (Factory default setting : Not Re- quired) Setting of user name f or secur ity protection. (Page 26 ) [5] P ass wor d (Factory default setting : Not Req ...

  • Sharp TL-M5200 - page 24

    -24 View Setting Detail List ([V]View All Setting) 1 1 1 1 1 Enter “v” and press the “Enter” key . Display all setting values(*). Enter number or symbol of item to be selected on the SETUP MENU . When setting, input the details to be set. Setting is carried out one item at a time, and saved at the end. ▼ SETUP MENU ----------------------- ...

  • Sharp TL-M5200 - page 25

    -25 Save Settings and Quit ([S]Save & Quit) Save set values and quit menu. 1 1 1 1 1 Enter “s” and press the “Enter” key . 2 2 2 2 2 Enter “y” and press the “Enter” key . ▼ SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gate way [4]User Name [5]Pas ...

  • Sharp TL-M5200 - page 26

    -26 IP Address Setting ([1]IP Address) Setting of IP address. 1 1 1 1 1 Enter “1” and press the “Enter” key . 2 2 2 2 2 Enter numerical value to be set and press the “Enter” key . Display IP address after change (*). Subnet Mask Setting ([2]Subnet Mask) Setting subnet mask. 1 1 1 1 1 Enter “2” and press the “Enter” key . 2 2 2 2 ...

  • Sharp TL-M5200 - page 27

    -27 Password Setting ([5]Password) Carrying out security protection using password. 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter passw ord and press the “Enter” key . Displa y set password (*). Note • Password can be up to 8 characters. • Y ou can input the characters below : a-z, A-Z, 0-9, -, _ • In the de f au ...

  • Sharp TL-M5200 - page 28

    -28 Disconnecting All Connec- tions ([D]Disconnect All) It is possible to disconnect all the TCP/IP connec- tions currently recognized b y the monitor . Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection. 1 1 1 1 1 Enter “d” and press the ? ...

  • Sharp TL-M5200 - page 29

    -29 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the monitor and a computer etc. is working normally . 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter IP address of device to be tested and press the “Enter” key . Display entered IP address (*1). ...

  • Sharp TL-M5200 - page 30

    -30 Setting of Search Port (ADVANCED[0]Search Port) Sets the port number used when searching for the monitor from the network. 1 1 1 1 1 Enter “0” and press the “Enter” key . 2 2 2 2 2 Enter numerical v alue and press the “Enter” key . Display set numerical value (*). Note • Set according to need. N o r mally , use with the f ac- tory ...

  • Sharp TL-M5200 - page 31

    -31 Multi Screen Projection Info • Bef ore setting up the multi screen projection, install Internet Explorer (version 5.0 or later). • Image quality may deteriorate when picture signals are input through multiple monitors with an RGB cable in connection. The monitor comes with the Multi-Screen function. Y ou can display one lar ge image using u ...

  • Sharp TL-M5200 - page 32

    -32 Multi Screen Projection Setting up the Multi Screen Projection Input Signal Following is an e xample of how to use 4 monitors. Video equipment Monitor 1 Computer RGB cable MONIT OR OUT terminal MONIT OR OUT terminal COMPUTER IN 1 terminal Monitor 2 RGB cable MONIT OR OUT terminal RGB cable RGB cable Monitor 3 Monitor 4 Composite video cable Dis ...

  • Sharp TL-M5200 - page 33

    -33 Multi Screen Projection 1 Access one of the four monitors via Internet Explorer . (See “Controlling the Moniotor Using Internet Explorer (V ersion 5.0 or later)” (page 16 ) f or the details.) 2 Click “Multi Screen” on the menu. • “Multi Screen” display will appear . 3 Select “2 X 2” on “Status”. 4 Click the assigning butto ...

  • Sharp TL-M5200 - page 34

    -34 Multi Screen Projection Notes on the Wide Multi Screen Projection Selecting “2 X 1”, “3 X 1”or “4 X 1” on “Status” (see page 33 ) allows you to create the wide m ulti screen. To create the wide multi screen with three monitor s lining up in single file from left to right (as shown abo ve), select “3 X 1” on “Status”, sel ...

  • Sharp TL-M5200 - page 35

    -35 Multi Screen Projection LAN terminal LAN cable (str aight-through type) Hub LAN terminal LAN terminal LAN terminal Computer LAN cable Setting up the Multi Screen Projection Controlling When y ou want to control the monitors collectively f or the multi screen pr ojection, connect LAN cab les to the LAN terminals and set both “TCP/IP” and “ ...

  • Sharp TL-M5200 - page 36

    -36 Multi Screen Projection Monitor 1 : Master Monitor 3 : Slave Monitor 2 : Slave Monitor 4 : Slave Computer LAN cable Hub LAN terminal LAN terminal LAN terminal LAN terminal LAN cable (straight-through type) 1 Change the TCP/IP settings for the computer as shown belo w . (See “Setting an IP Address for the Computer” on page 12 f or the detail ...

  • Sharp TL-M5200 - page 37

    -37 Multi Screen Projection 4 T urn on all of the monitors. 5 Access the monitor 1 from the com- puter via Internet Explorer . (See “Controlling the Monitor Using Internet Explorer (V ersion 5.0 or later)” on page 16 fo r the details.) 6 Click “Master & Slave” on the menu. 7 Select “Master” on “ Master & Slave Setting”. • ...

  • Sharp TL-M5200 - page 38

    -38 Multi Screen Projection Master Set Inputs ON ON OFF OFF OFF ON ON OFF OFF OFF OFF ON COMPUTER 1 COMPUTER 2 DV I HDMI VIDEO S-VIDEO Slave Set Inputs COMPUTER 1 COMPUTER 2 DV I HDMI VIDEO S-VIDEO Monitor 1 Monitor 2-4 13 Repeat the same procedure fr om the step 10 to 12 for the monitor 3 and 4. 14 Select inputs as specified in the table on the ri ...

  • Sharp TL-M5200 - page 39

    -39 Comm unication cannot be established with the monitor When connecting the monitor using serial-connection Check that the RS-232C terminal of the monitor and a computer or the commercially available controller are connected correctly . Check that the RS-232C cab le is a cross-over cab le. Check that the RS-232C port setting for the monitor ...

  • Sharp TL-M5200 - page 40

    -40 Tr oubleshooting Ta ke the follo wing steps for chec king the network settings for the computer . 1. Open a command prompt. • In the case of Windows ® 2000: click “start” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order . • In the case of Windows ® XP , Windows Vista ® : clic k “star t” ➔ “All Prog ...

  • Sharp TL-M5200 - page 41

    -41 Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also , check if an IP address is set. 1. Open a command prompt. • In the case of Windows ® 2000: click “start” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order . • In the case of Windows ® XP , Windows Vista ® : clic k ...

Produzent Sharp Kategorie Flat Panel Television

Dokumente, die wir vom Produzenten des Geräts Sharp TL-M5200 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Sharp
- Bedienungsanleitungen TL-M5200
- Produktkarten Sharp
- Informationsbroschüren
- oder Energieetiketten Sharp TL-M5200
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Sharp TL-M5200.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Sharp TL-M5200, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Sharp TL-M5200. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Sharp TL-M5200 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Sharp TL-M5200, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Sharp TL-M5200 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Sharp TL-M5200 verständlich ist.

Eine gänzliche Bedienungsanleitung von Sharp sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Sharp TL-M5200 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Sharp TL-M5200 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Sharp TL-M5200, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Sharp TL-M5200 - die uns die ersten Schritte während der Nutzung von Sharp TL-M5200 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Sharp TL-M5200 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Sharp TL-M5200 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Sharp TL-M5200?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Sharp TL-M5200 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Sharp TL-M5200 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)