Bedienungsanleitung Gossen Digiflash

20 Seiten Betrifft nicht
Download

Zur Seite of 20

Summary
  • Gossen Digiflash - page 1

    Digif lash Exposure meter f or flash and ambi ent li ght 15136 1/05.03 Operating Instruct ions ...

  • Gossen Digiflash - page 2

    2 GOSSEN Foto- und Lichtmeßte chnik Display Setting window Exp. ti mes Shutter speed scale Diffuser Aperture/ f-stops sca le Function button Eyelet for carrying strap Measuring key Battery compart ment Socke t for tripod Camera mounting clip (acc esso ry) ...

  • Gossen Digiflash - page 3

    GOSSEN Foto- und Licht me ß technik 3 Contents 1 The fun ctioni ng of th e Digifl ash . 4 1.1 Preparation and self-test ................ 4 1.2 Incident light and reflect ed light ...... 5 1.3 Duration of read-out in display ....... 5 2 Functio ns of t he Digifl ash ......... .. 6 2.1 Setting the film speed .... ................. 6 2.2 Exposure mea ...

  • Gossen Digiflash - page 4

    GOSSEN Foto- und Licht me ß technik 4 1 The functio ning of the Digi flash 1.1 Preparation and self-test Battery The Digiflash is powered by a 3 V Lithium battery, type CR 2032. When the battery is running low, BA T appears in the display. – The battery should be replaced as soon as possible. Wh en BA T is shown alone in the display, the batt er ...

  • Gossen Digiflash - page 5

    GOSSEN Foto- und Licht m e ß technik 5 be shown as set by t he factory. St andard setti ngs ISO 100/21 ° COR 0 ambient EV 8 t 1/125 flash EV 12 1.2 Incident light and reflected light Incident light metho d For the incident mode, the diffusor is to be shifted to the left and p laced in front of the measuring aperture. Taking measurements using the ...

  • Gossen Digiflash - page 6

    GOSSEN Foto- und Licht m e ß technik 6 2 Functions of the Digiflash Press the funct ion button for se lecting the individual functions of the Digiflash . Each tim e the button is pushed, the next function will be activated. The display panel will show t he functions in the following sequence: • Ambient light • Flash light • Tim er • Watc h ...

  • Gossen Digiflash - page 7

    GOSSEN Foto- und Licht m e ß technik 7 – Confirm the spe ed you selec ted by pushing the Function but ton until the OK-signal sounds and the D igiflash re- turns to the function "Exposure ambient light". The film speed is shown in the up- per right corner of the display. If the film speed is changed, t he measure- ment read-out stored ...

  • Gossen Digiflash - page 8

    GOSSEN Foto- und Licht m e ß technik 8 – Transfer that EV value from the display to the setting window in the calculator rin gs and place it precisely under the red indi- cat or l ine . – All the suitable com binations of aperture (f-stops) - t (shutter speeds) can now be seen at the up per part of the circ ular scales (see previous example) . ...

  • Gossen Digiflash - page 9

    GOSSEN Foto- und Licht m e ß technik 9 – Trigger the flash. – Transfer the value measured from the display to the window in the printed sca- les above and set it precisely under the red indicator line. – Read the f/stop in the upper part of the scale opposite the sync speed you had preselected (for 1/90 read between 1/60 and 1/125). 2.3.3 Fi ...

  • Gossen Digiflash - page 10

    GOSSEN Foto- und Licht m e ß technik 10 2.4 T a king a measuremen t out side the measu ring range The Digiflash will not produce any useable readings outside its measuring range: in the display Eu (too dark) or E n (too bright) will appear . 2.5 Contrast m easurements – Use t he Function button to select the function "Exposure ambient light ...

  • Gossen Digiflash - page 11

    GOSSEN Foto- und Licht m e ß technik 11 2.6 Setting correction va lues In order to deliberately change the exposure of your photos, y ou may adjust the factory calibration. – Remove the battery from the Digiflash and press one of the buttons ( battery memory will be deactivated). Put the bat- tery back in the compartment. The meter will then mak ...

  • Gossen Digiflash - page 12

    GOSSEN Foto- und Licht m e ß technik 12 2.7 Fu nct ion TI MER A timer f unction is prov ided in the Digiflash , useful for long exposure or other timings ranging from one second to thirty minutes. – Use the function but ton to select the function TIMER and hold it down until the OK-signal sounds. The display shows the last value used. The read-o ...

  • Gossen Digiflash - page 13

    GOSSEN Foto- und Licht m e ß technik 13 – To pause the count-down, push the measuring key; pressing it again will restart the count-down. The timer will work in t he background so that you can use other measurements. 2.8 W atch/Alarm clock W A TCH – Setting the ti me – Use the function button to s elect the function WATCH and hold the k ey d ...

  • Gossen Digiflash - page 14

    GOSSEN Foto- und Licht m e ß technik 14 – Use the key M to set the hours an d confirm with the funct ion button. The read-out "minutes" in the display will flash. – Use the key M for setting the minut es. To confirm settings hold down the function button until the OK-signal is heard. ALARM CLOCK – Use funct ion button to enter the ...

  • Gossen Digiflash - page 15

    GOSSEN Foto- und Licht m e ß technik 15 2.9 Measuring temperatures – Use the function but ton to select the function TEMPE RATURE and hold t he button pressed down until the OK-signal sounds. To c hange between ° C or ° F read-outs, press and hold the funct ion button until the display changes. The Digiflash will indicate t he actual ambi- ent ...

  • Gossen Digiflash - page 16

    16 GOSSEN Foto- und Lichtm e ß technik 3 Service and rep airs In the event that your Digiflash is not work- ing to your complete satisfaction, please send it to: GOSSEN Fot o- und Lichtme ß technik GmbH Thomas-Mann-Str. 16-20 D - 90471 N ü rnberg or to the G OSSEN agenc y in your count ry. ...

  • Gossen Digiflash - page 17

    GOSSEN Foto- und Licht m e ß technik 17 4 T echnical dat a Exposure meter Measuring modes Ambient li ght Flash light (non c ord) Incident light method Reflected light method Contrast measurem . Light sensor sbc photo diode Meas. range ambient light (when ISO 100/21 ° ) EV 0 to 18 Shutter speeds 1/2000 s to 4 min Apertur es f/1 to f/3 2 Meas. rang ...

  • Gossen Digiflash - page 18

    18 GOSSEN Foto- und Lichtm e ß technik Display Digital read-out of measuring values and analogue scales Duration of read-out The DF will always display the last function used Batt ery 1 x 3 V Li thium battery CR 2032 Operating temp. – 10 ° C ... 6 0 ° C Dimensions 75 x 50 x 23 mm Weight 40 g incl. battery Accessories incl. Battery, car rying c ...

  • Gossen Digiflash - page 19

    GOSSEN Foto- und Licht m e ß technik 19 ...

  • Gossen Digiflash - page 20

    Printed in German y • Subject to ch ange without notice GOSSEN F oto- und Lichtme ß te chnik GmbH Thomas- Mann-Str . 16- 20 D-90 471 N ü rnberg Phone: +49 911 / 8602-181 Fax: +4 9 91 1 / 860 2-142 http://w ww .gossen-ph oto.de ...

Produzent Gossen Kategorie Light Meter

Dokumente, die wir vom Produzenten des Geräts Gossen Digiflash erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Gossen
- Bedienungsanleitungen Digiflash
- Produktkarten Gossen
- Informationsbroschüren
- oder Energieetiketten Gossen Digiflash
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Gossen Digiflash.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Gossen Digiflash, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Gossen Digiflash. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Gossen Digiflash ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Gossen Digiflash, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Gossen Digiflash hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Gossen Digiflash verständlich ist.

Eine gänzliche Bedienungsanleitung von Gossen sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Gossen Digiflash bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Gossen Digiflash befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Gossen Digiflash, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Gossen Digiflash - die uns die ersten Schritte während der Nutzung von Gossen Digiflash erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Gossen Digiflash hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Gossen Digiflash im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Gossen Digiflash?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Gossen Digiflash nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Gossen Digiflash hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)