-
Airlink SkyIPCam310 - page 1
SkyIPCam310 Power Over Ethernet Network Camera Model # AICP310 User’s Manual Ver 1A ...
-
Airlink SkyIPCam310 - page 2
1 Table of Contents ABOUT THIS GUIDE ............................................................................................................... ....2 1. INTRODUCTION......................................................................................................................3 1.1 F EATURES AND B ENEFITS ................................ ...
-
Airlink SkyIPCam310 - page 3
2 0 About This Guide This manual provides instructions and illustra tions on how to use your SkyIPCam310 PoE Network Camera, includes: z Chapter 1, Introduction , provides the general information on the camera. z Chapter 2, Installation , describes the hardware and software installation procedure for the SkyIPCam310. z Chapter 3, Security , explain ...
-
Airlink SkyIPCam310 - page 4
3 1 1. Introduction Thank you for purchasing the SkyIPCam310 PoE Ne twork Camera, a camera device that can be connected directly to an Ethernet or Fast Ethernet network. Compared to the conventional PC Camera, the SkyIPCam310 features a built-in CPU and web-based solutions that can provide a cost-effective solution to transmit real-time high-qualit ...
-
Airlink SkyIPCam310 - page 5
4 needs. When the external device is connected, you could configure the settings an d control the device from the RS485 window of Web Configuration Utility. Remote Utility The powerful IPView Pro application assigns the administra tor with a pre-defined user ID and password, allowing the administrator to modify the camera setting s from the remote ...
-
Airlink SkyIPCam310 - page 6
5 1.3 System Requirement s Networking 10Base-T Ethernet or 100Base-TX Fast Ethernet. Accessing the Camera For Web Browser Users Operating System: Microsoft® Windows® 98SE/ME/2000/XP/Vista CPU: Intel Celeron 1.1GHz or above (Intel Pentium 4 is preferred) Memory Size: 128MB or above Resolution: 800x600 or above Microsoft® I ...
-
Airlink SkyIPCam310 - page 7
6 3. Internal MIC The built-in omni-directional microphone allows the camera to receive sound and voice. Rear Panel 1. Network Cable Connector The SkyIPCam310’s rear panel features an RJ -45 connector for connections to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should b e Category 5 twisted-pair cable). The port support ...
-
Airlink SkyIPCam310 - page 8
7 Top/Bottom Panel Top Panel Bottom Panel Screw Hole Located on the top/bottom panel of the camera , the screw hole is used to connect the camera stand onto the camera by attaching the screw head on the camera stand into the screw hole of the camera. Screw Hole Screw Hole ...
-
Airlink SkyIPCam310 - page 9
8 2 2. Hardware Installation 2.1 Att aching the Camera to the St and The SkyIPCam310 comes with a camera stand (optional), which is equipped with a swivel ball screw head that can be attached to the camera's bottom screw hole. Attach the camera stand to the camera and station it for your application. There are three holes located in the base o ...
-
Airlink SkyIPCam310 - page 10
9 2.4 Setting up the Camera Installing the Setup Wizard Step 1 Insert the provided CD and wait for the autorun screen to appear. Step 2 Click on Install Setup Wizard . Note: If the autorun screen does n o t appear autom atically, go to Start , Run , type D:WizardSetup.ex e (where D is t he letter of your CD drive) and click OK . Step 3 Click Nex ...
-
Airlink SkyIPCam310 - page 11
10 Step 4 Click Yes to accept the Licen se Agreement. Step 5 Click Nex t to accept the default Destination Folder. Step 6 Click Finish to complete the installation. ...
-
Airlink SkyIPCam310 - page 12
11 Using the Setup Wizard Step 1 Go to Start > (All) Programs > AirLink101 IP Camera Se tup Wi zard > AirLink101 IP Camera Setup Wizard . Step 2 Select the IP Camera you want to c onfigure from the list and click on the Wizard button. ...
-
Airlink SkyIPCam310 - page 13
12 Step 3 If the Camera’s default IP address i s on a different subnet, the following message will appear. Click Yes to continue. If you do not receive this messa ge, skip to Step 6 . Step 4 Enter admin for both the Admin ID and Password and cli ck OK . ...
-
Airlink SkyIPCam310 - page 14
13 Step 5 The Wizard will automatically generate an IP addres s for the camera, if this addre ss is not in use by any other device in your local network, click OK . Otherwise, enter an available IP addre ss (ex. 192.168.x.240) and click OK . Step 6 Enter admin for both the Admin ID and Password field and click Next . Optionally, you can change the ...
-
Airlink SkyIPCam310 - page 15
14 Step 8 Verify that all the fiel ds are correct and click Restart to save the settings and reboot the camera. Viewing Images Step 1 At the Setup Wizard, select the desired camera from the li st and click on the Web Config button. ...
-
Airlink SkyIPCam310 - page 16
15 Step 2 Enter the username and passwo rd for the net work camera. The default username and password are both “ a dmin” . Step 3 The web based viewing page will appea r. You c an view live video by selecting eith er the Activ eX Mode (Internet Explorer only) or the Java Mode (Internet Explorer and Netscape). ...
-
Airlink SkyIPCam310 - page 17
16 Step 4 If you select ActiveX Mode, you may be prompt to install the ActiveX Control. Click on the yellow bar to on the top of the screen and click on Install Activ e X Control . Step 5 Click on Install . ...
-
Airlink SkyIPCam310 - page 18
17 Step 6 You can focus the camera by turning the came ra’s lens cloc kwise or coun ter-clockwise . Note: ActiveX and/or Java Applet must be installe d and enabled on your Web Browse r (Internet Explorer or Netscape) before you can view the live videos. For mo re information please refer to the User’s Manual in the provided CD. Step 7 If you ne ...
-
Airlink SkyIPCam310 - page 19
18 and "Admin Password" when you are the first time to use the SkyIPCam310. Once the ID and Password are defined, only the administrator has the access to management the SkyIPCam310. This procedure should be done as soon as possible since the se curity features with the SkyIPCam310 will not be enabled until the "Admin ID" and &q ...
-
Airlink SkyIPCam310 - page 20
19 SOHO Internet Camera SOHO Wireless Internet Camera Home Applications Diagram SOHO SOHO Applications Diagram ...
-
Airlink SkyIPCam310 - page 21
20 8 5. Using the Camera You can access and manage the SkyIPCam310 through: 1) a web browser, and 2) the enclosed software IPView Pro. This chapter describes the Web Configuration Utility, and provides the instructions on using the camera with a web browser. 5.1 Web Configuration Utility The SkyIPCam310 must be configured through its built-in Web-b ...
-
Airlink SkyIPCam310 - page 22
21 Click System Administration to prompt a login dialog window, and type the default username/ password ( admin / admin ) in the corresponding boxes. Then, click OK to enter the Configuration Utility. 5.2 System Administration The Configuration Utility contains eleven options in the top menu bar, including: System , Date/Time , Video/Audio , Networ ...
-
Airlink SkyIPCam310 - page 23
22 Date & Time - Server’s Time: Display the current date/time settings of the camera. - TimeZone: Select the time zone for the region from the pull-down menu. (Please refer to the Appendix for the time zone selection table.) - Synchronized with Time Server: Select th is option and the time will be based on GMT setting. When selecting the opti ...
-
Airlink SkyIPCam310 - page 24
23 Environment Select Outdoor or Indoor according to the installation lo cation of the camera. Light Frequency Select 60HZ or 50HZ . Video Resolution Select the desired video resolution from three formats: 160x120 , 320x240 , and 640x480 . The higher setting can obtain better quality; however, it will use more resource within your network. Compress ...
-
Airlink SkyIPCam310 - page 25
24 - Brightness: Adjust the brightness level ranging from -64 to +64. - Saturation: Adjust the colors level ranging from -64 to +64. - Contrast: Adjust the contrast level ranging from -64 to +64. - Sharpness: Adjust the sharpness level ranging from -6 to +6. Network The Network window contains commands that allow you to set up networking configurat ...
-
Airlink SkyIPCam310 - page 26
25 IP Assignment - Use Static IP Address: You can select this option and enter the IP address directly. The default settings are: • IP Address – 192.168.1.240 • Subnet Mask – 255.255.255.0 • Default Gateway – 192.168.1.1 - Obtain IP address automatically via DHCP: If your netwo rk uses the DHCP server, select this option. According to t ...
-
Airlink SkyIPCam310 - page 27
26 Administrator This field is used for entering the administrator password to access the settings. Enter the password in the Admin Password box, and then enter the same one again in the Confirm Password box to confirm the password. The default setting for Admin is blank space (Nu ll String). For security purpose, you are strongly recommended to se ...
-
Airlink SkyIPCam310 - page 28
27 Trigger The Trigger window contains the control settings for external device through the I/O port, and the settings required for e-mail. Enable Trigger Email - SMTP Server Address: To use the e-mail alert function, you must enter the mail server address in the field. - Sender e-mail Address: Enter the e-mail Address of sender. - Receiver e-mail ...
-
Airlink SkyIPCam310 - page 29
28 Access Control Click the Access Control button to bring up a dialog window that contains list of users, allowing the administrator to assign legal users who are permitted to control the trigger output. Upload To upload the image to FTP server, you need to configure the related settings in the Upload window. FTP Server This field contains the fol ...
-
Airlink SkyIPCam310 - page 30
29 - Directory Path: Enter an existing folder name in this field, and the images will be uploaded to the given folder. Operation To enable the FTP upload function, check the Enable upload video to FTP server option, and then configure the following settings according to your necessary. - Always: Allows you to upload the video to FTP server continuo ...
-
Airlink SkyIPCam310 - page 31
30 Check the Enable item to enable the function of your camera, and configure the related settings in the following fields. NOTE: When RS485 function is enabl ed, the system will provide the additional control buttons on the View Image screen (ActiveX mode and Java mode). See the illustra tions on page 44and 47. Port setting Select the proper proto ...
-
Airlink SkyIPCam310 - page 32
31 Information The Information window provides general information of the camera, including the Model name, Firmware Version, Mac Address, and IP Address. Model The camera’s model name will be display here. Firmware Version The field displays the firmware version of the camera. MAC Address This field displays the MAC Address of the camera. IP Add ...
-
Airlink SkyIPCam310 - page 33
32 Reboot Do you really want to reboot this device? Click YES from this option, and you can restart the camera just like turning the device off and on and saved settings are retained. Factory Reset Do you really want to factory reset this device? Click YES from this option, and you can resume all factory default settings for the camera. NOTE: You h ...
-
Airlink SkyIPCam310 - page 34
33 Camera Name/Location: The Camera name and location will be displayed when the Camera Name/Location fields are entered in the Web Configuration Utility. Video/Audio: You can enable/disable the video and audio function by clicking the desired selection . Trigger Out: you can turn on/off the output device manually by clicking the OFF button. Browse ...
-
Airlink SkyIPCam310 - page 35
34 When you select Popular protocol command setting in RS485 configuration window (see page37), you can use the Preset Position pull-down menu to select one position, then click Go To to move the camera’s lens to your desired position. If you select Custom protocol setting in RS485 configuration window (see page37), you can use the Custom Command ...
-
Airlink SkyIPCam310 - page 36
35 The function of these control buttons are the same as they are in ActiveX mode screen (see page 44). ...
-
Airlink SkyIPCam310 - page 37
36 9 6. IPView Pro This chapter describes IPView Pro, which is a powerful software application design ed with a user-friendly interface for ease of control and navigation requirements. 6.1 Inst allation Step 1 Insert the CD-ROM into the CD-ROM drive to initiate the auto-run program. The menu screen will appear as below: Step 2 Click the IPView Pro ...
-
Airlink SkyIPCam310 - page 38
37 Step 3 Read and accept the License Agreement; then, click Yes . Step 4 Choose the destination location. If no sp ecific requirement, leave the default setting and click Next . Step 5 The InstallShield Wizard starts to install the software, and the progress bar in dicates the installation is proceeding. ...
-
Airlink SkyIPCam310 - page 39
38 Step 6 Click Finish to complete the installation. ...
-
Airlink SkyIPCam310 - page 40
39 6.2 Getting S t arted This section describes the User Interface of IPView Pro, with detailed procedures fo r using the application. To launch IPView Pro, click Start > Programs > IPView Pro > IPView Pro . The main screen will appear as below: NOTE: IPView Pro requires the system’s resolution setting up to 1024x768. Ple ase configure t ...
-
Airlink SkyIPCam310 - page 41
40 5 Rotate image angle Click to rotate the image shown in the View Windo w. 6 Snapshot Click to capture a still imag e from the View Window. 7 Audio ON/OFF Click to turn on/off the camera’s audio. 8 Zoom Mode Click to zoom in/out the image in the View Window. Select the view mode from these buttons. Show one camera in View Window. Show four c am ...
-
Airlink SkyIPCam310 - page 42
41 6.3 Using IPV iew Pro Adding a Camera To add a camera: 1. Click the System Configuration button to enter the System Configuration. If you are not sure of the camera’s IP address, you can click Search to search the available camera(s) within the network. 2. Select the camera you want by highlighting it, and then click Add Camera . The camera fo ...
-
Airlink SkyIPCam310 - page 43
42 3. Click Save , and then click the System Configuration button to return to View Window. The selected camera’s video will be displayed now. You can click Save as to sav e the selected cameras into the desired path and the selected cameras can be reloaded by load button. Alternately, you can add a camera by entering the its IP address directly: ...
-
Airlink SkyIPCam310 - page 44
43 Viewing a Camera From the View Modes of the panel, you can select one-camera mo de or other modes to display your video. IPView Pro allo ws a maximum of 16 camera s for v i ewing. For example, if you use only one camera, select one-ca mera mode ( ), and the View Window will display the v iew as figure 1 . If there are four cameras, select four-c ...
-
Airlink SkyIPCam310 - page 45
44 Playing Recorded Video The recorded video clips are saved in your computer, and can be played using Windows Media Player. To start playback, simply click the Play button on the panel, and the following dialo g screen will appear, allowing you to select the file to playback. Select the recorded file in the computer, and then click OK . 6.4 Config ...
-
Airlink SkyIPCam310 - page 46
45 Camera Configuration In this field, you can add/delete the camera (as described in the previous section). Also, you can configure the following settings: Web Configuration In the left column, selecting the Web Configuration item will launch the Web Configuration Utility in View Window. You can configure these settings according to the descriptio ...
-
Airlink SkyIPCam310 - page 47
46 - Detect Region: • Full picture – When you select this option, the camera will monitor the whole area. • Custom region – Click Add Region , and then use mo use to draw an area in the view screen; when some motion detected within the area, the camera starts recording automatically. You c an set multiple areas in the view screen. Click Del ...
-
Airlink SkyIPCam310 - page 48
47 - Invoke Alarm: Select this option to enable alarm when some motion detected by the system. - Send e-mail: When this option is checked, click the Mailing Configuration in the left column to enter the required information (see the following section). - Play music: You can use the music file to alert the event. Click Browse music file to select th ...
-
Airlink SkyIPCam310 - page 49
48 - Factory Reset: Restore the factory default settings of the camera. Do you really want to factory reset this device? Click Yes in the pop-up dialog box to confirm. - Update Firmware: When new firmware is available, y ou can upgrade it using this option. Click Browse to find the firmware file, and then click Update . Mailing Configuration When M ...
-
Airlink SkyIPCam310 - page 50
49 Recording Configuration In this field, you can configure the storage settings. - Log Storage: • Reserved HDD Space For MS-Windows OS – You can reserve 500 MB to 10000 MB hard disk space for the program. • Each Recording File Size – If the recorded video files reach the file size limit, video images will be recorded into another file auto ...
-
Airlink SkyIPCam310 - page 51
50 folder; click Delete to remove a selected path setting. Please note that you are not allowed to delete a path setting if there is only one setting in t he list. - Recycle: You can check this opt ion to clear the files when the unreserved space of your hard disk is filled. The available settings are from 200 MB to 50000 MB . - Resume last time’ ...
-
Airlink SkyIPCam310 - page 52
51 - Week Mode: First, select the camera desired from the pull-down menu. Then, setup the time in the Start / Stop fields, and select the weekday from the buttons. Click Add to add the recording schedule to the list. Click Save to save the settings. Others When multiple cameras connected, this option allows the system to disp lay these views as the ...
-
Airlink SkyIPCam310 - page 53
52 Log List This filed displays the user(s) information, which include the Date, MAC address, and the brief description of events. Account This filed allows you to set the Admin ID and Admin Password . You can also check the Login password check option to secure your camera by checking the login password. ...
-
Airlink SkyIPCam310 - page 54
53 About This filed provides information of the software application. ...
-
Airlink SkyIPCam310 - page 55
54 10 7. Appendix 7.1 Frequently Asked Questions SkyIPCam310 Features Q: What is a Network Camera? A: The Network Camera (Internet Camera) is a standalone system connecting directly to an Ethernet or Fast Ethernet network. It is different from the conventional PC camera, the SkyIPCam310 is an all-in-one system with built-in CPU and web-based soluti ...
-
Airlink SkyIPCam310 - page 56
55 Therefore, it is necessary to open port 8481 of the network for remote users to access the camera. 7.2 PING Y our IP Address The PING (Packet Internet Groper) command can determine whether a specific IP address is accessible by sending a packet to the specific address and waiting f or a reply. It can also provide a very useful tool to confirm if ...
-
Airlink SkyIPCam310 - page 57
56 Q: Why does the Power LED not light up constantly? A: The power supply used might be at fault. Confirm that you are using the provided power supply DC 5V for the SkyIPCam310 and verify that the power supply is well connected. Q: Why does the Link LED not light up properly? A1: There might be a problem with the network cable. To confirm th at the ...
-
Airlink SkyIPCam310 - page 58
57 7.4 Adjust SkyIPCam310 Focus To adjust the focus of the lens, you need to turn the lens slowly in either clockwise or anti- clockwise direction until the desired image appears. DO NOT over turn the lens in either of the directions, as it will be out of focus. NOTE: You can further adjust the SkyIPCam310's image qualit y through System Admin ...
-
Airlink SkyIPCam310 - page 59
58 7.5 I/O T erminal Application Typically used in association with programming scripts for developing applications for motion detection, event triggering, alarm notification via e-mail, and a variety of external control functions. The 6-pin I/O Terminal Block is located on the rear panel an d provides the interface to: a photo-coupled switch outpu ...
-
Airlink SkyIPCam310 - page 60
59 1 2 PTZ Camera ...
-
Airlink SkyIPCam310 - page 61
60 7.6 S pecifications Video specification Resolution: 640 x 480 pixel Sensor: Color CMOS sensor Lens: f: 6.0 mm, F: 1.8 Gain control: Automatic Exposure: Automatic White Balance: Automatic Image (Video Setting) Compression: M-JPEG Image frame rate: CIF, QCIF, VGA @ 30fps Support different frame rate for different connections depending on connectio ...
-
Airlink SkyIPCam310 - page 62
61 Operating environment Operating temperature: 5 O C ~ 40 O C Storage temperature: -25 O C ~ 50 O C Humidity: 5% ~ 95%, non-condensing EMI FCC and CE ...
-
Airlink SkyIPCam310 - page 63
62 11 12 13 Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Web Site: www.airlink101.com * Actual data throughput will vary. Network conditions and environm ental factors lower actual data throughput rate. Specificati ons are subject to change without notice. All products and trademarks ar e the propert y of their respect ...
Haben Sie eine Frage bezüglich Airlink SkyIPCam310?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Airlink SkyIPCam310 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Airlink SkyIPCam310 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.