Bedienungsanleitung Macsense Connectivity Digital Wattmeter DWM-4

12 Seiten 0.99 mb
Download

Zur Seite of 12

Summary
  • Macsense Connectivity Digital Wattmeter DWM-4 - page 1

    - 1 - Welcome : Thank you for your purchase of the DWM-4 Digital Wattmeter. The DWM-4 represents an advancement in technology that has never before been available in RF power measurement. With the integration of a microprocessor to existing RF sensor technology, the DWM-4 offers the flexibility of digital processing while keeping the interface to t ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 2

    - 2 - in the assembly instructions to assist the builder. These can be used for parts identification and PC board placement. Assembly: You will first install (locate, place, and solder in place) the parts on the DWM-4 Main PC board. Use the silk screen layout in the back of this manual to assist in locating where parts are to be installed. ___ Inst ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 3

    - 3 - ___ Install the socket for U1. Note the orientation of the socket. The flattened corner goes in the upper left, toward the 14-pin DIP socket for U3. Do not install U1 (the 68HC11) until later. ___ Install the 8 MHz crystal. ___ Install the electrolytic capacitor, C2, 10uf radial. Note the polarity. ___ Install the 1/8" stereo jacks, J1-5 ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 4

    - 4 - ___ Install the LCD Module in the chassis. Use the 4 black flat head screws, the two #4 nylon washers and four nuts. Use the washers on the Status/SWR side of the chassis. Do not over tighten the mounting screws. ___ Install the SPST toggle switch (SW1) in the chassis in the Power On position. Remove the nut and one washer from the switch. Pl ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 5

    - 5 - You are now ready to mount the DWM PC board in the chassis. ___ Install the DWM-4 PC board in the chassis using four screws, nylon spacers, washers and nuts. Do not drill out the holes in the PC board ___ Install U1 (the 68HC11) by carefully pressing it into place in its socket. Note that U1 has a flattened corner that should match the socket ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 6

    - 6 - ___ Install the .01uf monolithic capacitors, C1 and C2. ___ Install 1/8" ste reo jack. ___ Unwrap the enclosure. Install the SO-239 connectors. Put one #4 screw in hole and place two nuts on the screw. Repeat with the other three screws. Do not tighten them at this time. ___ Place the PC board onto the SO-239s. Align the 1/8” jack with ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 7

    - 7 - HF/QRP Remote Sensor Assembly Instructions ___ Wind T1 with 10 turns using the red and gr een #28 gauge wire. T1 is the small, black toroid just under one half inch in diameter. See picture below and wind this in bifiliar fashion by using two lengths of wire and winding them at the same time. It doesn’t matter if you twist them or wind them ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 8

    - 8 - ___ Install C4, 3.5-13 pf trimmer capacitor. Note that C4 has two pins that are common (connected). They should line up with the two holes in the PC board that are connected together with a trace on the bottom. ___ Install T1. It lies flat against the PC board and the #18 wire will pass through the center (you will install this later). Hold t ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 9

    - 9 - Installation: The DWM-4 operates from an 11 to 15 volt DC power source. The current requirement is about 75 mA. Be sure to use a power supply or power adapter that meets these requirements. The coaxial DC jack on the back of the display unit will accept a plug with an OD of 5.5 mm and ID of 2.5 mm. You can use any 50 ohm cable to connect the ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 10

    - 10 - menu offers information about each of the four sensor inputs. Some items are common across different menus. There are two basic wattmeter modes: setup and operate. During setup, you can select bargraph or numeric display, peak or average display, set SWR alarms, and select which sensor type is connected to each input along with a power range ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 11

    - 11 - At a minimum, a 100 W HF radio and good 50ohm dummy load can be used to calibrate the HF sensor and display unit. Even if you know how much power your radio emits, consider using an additional wattmeter of known accuracy to assist you during the calibration process. Start by setting R1 through R8 to their center positions. Connect the HF sen ...

  • Macsense Connectivity Digital Wattmeter DWM-4 - page 12

    - 12 - was installed correctly. Make sure U3 is installed correctly. Check D1 for polarity. Check the SIP resistor (RP1) for proper orientation. No Display: Make sure the 14-pin ribbon cable is installed and oriented properly. Be sure the nylon washers are in place on the two nuts closest to the outside. Turn R25 (LCD Contrast) fully counter- clock ...

Produzent Macsense Connectivity Kategorie Stereo System

Dokumente, die wir vom Produzenten des Geräts Macsense Connectivity Digital Wattmeter DWM-4 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Macsense Connectivity
- Bedienungsanleitungen Digital Wattmeter DWM-4
- Produktkarten Macsense Connectivity
- Informationsbroschüren
- oder Energieetiketten Macsense Connectivity Digital Wattmeter DWM-4
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Macsense Connectivity Digital Wattmeter DWM-4.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Macsense Connectivity Digital Wattmeter DWM-4, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Macsense Connectivity Digital Wattmeter DWM-4. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Macsense Connectivity Digital Wattmeter DWM-4 ansehen.

Die komplette Bedienungsanleitung des Geräts Macsense Connectivity Digital Wattmeter DWM-4, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Macsense Connectivity Digital Wattmeter DWM-4 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Macsense Connectivity Digital Wattmeter DWM-4 verständlich ist.

Eine gänzliche Bedienungsanleitung von Macsense Connectivity sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Macsense Connectivity Digital Wattmeter DWM-4 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Macsense Connectivity Digital Wattmeter DWM-4 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Macsense Connectivity Digital Wattmeter DWM-4, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Macsense Connectivity Digital Wattmeter DWM-4 - die uns die ersten Schritte während der Nutzung von Macsense Connectivity Digital Wattmeter DWM-4 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Macsense Connectivity Digital Wattmeter DWM-4 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Macsense Connectivity Digital Wattmeter DWM-4 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Macsense Connectivity Digital Wattmeter DWM-4?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Macsense Connectivity Digital Wattmeter DWM-4 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Macsense Connectivity Digital Wattmeter DWM-4 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)