Deutsch dropdown-ico

Bedienungsanleitung CDA SK650

32 Seiten Betrifft nicht
Download

Zur Seite of 32

Summary
  • CDA SK650 - page 1

    Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu sk650 Single Pyrolytic Oven Manual for Installation, Use and Maintenance ...

  • CDA SK650 - page 2

    2 Important This appliance must only be used for the purpose for which it is intended, i.e. domestic cooking, defrosting and reheating foods. Any other use could be dangerous and may lead to premature failure of the appliance. The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this produ ...

  • CDA SK650 - page 3

    3 CE Declarations of Conformity: This oven has been designed, constructed and marketed in compliance with safety requirements of EEC Directive 2006/95/EEC (L ow voltage) and requirements of EMC Directive 2004/108/EEC. This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical s ...

  • CDA SK650 - page 4

    4 Important • Do not dismantle any parts withou disconnecting the oven from the mains power supply . • Do not use the appliance if any part is broken (for example a glass). Disconnect it from the mains and call CD A Customer Care. • Before using the oven, it is recommended to run it empty at the maximum temperature for an hour to remove any s ...

  • CDA SK650 - page 5

    5 • In order to avoid damage to the oven enamel coat, do not cover the oven base with any item (e.g. aluminum foil, pans and the likes). • Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass. • Abrasive detergents and steam clea ...

  • CDA SK650 - page 6

    6 • Do not place hot enamel parts in water . Leave them to cool first. • Do not allow vinegar , coee, milk, saltwater , lemon or tomato juice to remain in contact with enamel parts. • The oven can require increased ventilation on pyrolytic programmes. This can be achieved either from an open window or the use of a fan. Fig. 1 below shows ...

  • CDA SK650 - page 7

    7 Fig. 2 Fitting Out Y our Appliance Oven rack positions The oven racks can be positioned in any one of four pairs of guides at diering levels. At each level is a pair of supports formed in the side walls of the oven cavity . • Always be sure to position the oven racks before turning on the oven. • Make sure that the racks are level once the ...

  • CDA SK650 - page 8

    8 The Control P anel Fig. 3 Fig. 4 T emperature control Digital Display Function control Door lock LED Time LED Heating LED Timer indicator T emperature LED Auto timing indicator Auto cooking indicator Digital Display in Detail ...

  • CDA SK650 - page 9

    9 Fig. 5 Function Control Knob in Detail Defrost Conventional oven Fan with lower heat Light Fan oven Fanned half grill O Conventional Eco oven Half grill Full grill Pyrolytic clean ...

  • CDA SK650 - page 10

    10 Before First Use When the oven is connected to the electrical supply the latch mechanism runs an automatic self-test by locking then unlocking the oven door . This operation takes about half a minute. The “Door lock LED” flashes while this test is performed, then turns o when the test is completed. The same process is repeated after ever ...

  • CDA SK650 - page 11

    11 Before using the oven for the first time we recommend that you clean it with soapy water , rinse carefully and then heat on the fan oven setting at maximum temperature for 30 minutes. A slightly unpleasant smell may be produced, caused by grease remaining on the oven elements from the production process. General Settings & Use Note: The “ ...

  • CDA SK650 - page 12

    12 T o turn the oven o T urn the “Function control” knob to the “O ” position, the oven gives three short beeps and the word ”O ” appears briefly on the display . The functions available on the “Function control” knob are: Oven light The oven light may be turned on by turning the “Function control” knob to the “Oven ...

  • CDA SK650 - page 13

    13 Conventional Eco oven T urn the “Function control” knob to the “Conventional Eco oven” position. In this setting, the oven cooling fan only comes on when the oven is hot, saving some electricity . The cooking temperature defaults to 190°C and can be set between 50-250°C in 5˚C increments by turning the “T emperature control” knob. ...

  • CDA SK650 - page 14

    14 Fanned half grill T urn the “Function control” knob to the “Fanned half grill” position. The fanned half grill programme uses the grill element for grilling and the fan to help circulate heat around the food. The cooking temperature defaults to 230°C and can be set between 50-250°C in 5˚C increments by turning the “T emperature cont ...

  • CDA SK650 - page 15

    15 Full Grill T urn the “Function control” knob to the “Full grill” position. The full grill programme uses the centre and outer grill elements to provide top heat for grilling or browning foods. The rack should be placed in as high a position as possible to bring the food close to the elements. The food needs to be turned over during cooki ...

  • CDA SK650 - page 16

    16 Please note: Before any pyrolytic programme, remove all shelves, trays and other accessories from the oven and clean up any major spills to avoid the risk of fire or ex cessive smoke. Do not hang towels or cloths on the oven handle during pyrolysis. T urn the “Function control” knob to the “Pyrolytic clean” position. The programme immed ...

  • CDA SK650 - page 17

    17 • It is now set at the revised time. When the pyrolytic clean finishes the display shows “ P --- ” and the “ Auto timing indicator” flashes. • The display is cleared when the “Function control” knob is turned to the o position. • The door remains locked until the inside of the oven drops below the safety threshold. When th ...

  • CDA SK650 - page 18

    18 Timer and Minute Minder Timer functions are selected by pressing the “T emperature control” knob. This switches the digital display between them:- Clock function: The display shows the current time. Minute minder function: The display shows a countdown time until the oven beeps. Duration function: The display alternates between the word “d ...

  • CDA SK650 - page 19

    19 showing the current time. The “ Auto timing indicator” and the “ Auto cooking indicator” illuminate. • The timer is now set. • At the end of the set time, the oven switches o and the beeper sounds. • The beeper can be silenced by briefly turning the “T emperature control” knob clockwise or anticlockwise, then letting it ret ...

  • CDA SK650 - page 20

    20 • The beeper can be silenced by briefly turning the “T emperature control” knob clockwise or anticlockwise, then letting it return to its rest position. Programming delayed cooking This is achieved by programming an end time (when you want the food ready) and also programming a cooking time (as the recipe). Minute minder The minute minder ...

  • CDA SK650 - page 21

    21 Care and Maintenance IMPORT ANT : Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. Y ou should always allow the oven to cool fully after use before undertaking any cleaning or maintenance. Changing the oven lamp • R emove all shelves and the grill pan from the oven. • R emove the glass cov ...

  • CDA SK650 - page 22

    22 Oven Door R emoval For Cleaning T o remove the oven door (Fig. 7) 1 Open the door completely . 2 Lift the hinge bracket (1). 3 Hold the door firmly on both sides using both hands and close it as far as the stops. 4 Pull the door out, holding it firmly because it is heavy . 5 Place the door in a safe and convenient location. T o re-install the ...

  • CDA SK650 - page 23

    23 Door Glass R emoval and R eplacement Note: Suitable protective gloves should be worn for this process. • R emove the door , as above and lie it, face down, on a firm surface, protected with a soft cloth. • Press the buttons on the two side covers at the same time to release and remove the upper strip (Fig.9). Lay it safely aside . • Slide ...

  • CDA SK650 - page 24

    24 Cleaning Y ou should only use non-abrasive cleaners. Any abrasive cleaners (including Cif ) will scratch the surface and could erase the control panel markings. Y ou should not use cleaning products with a chlorine or acidic base. Any spillages should be cleaned o immediately , especially any alkaline or acidic substances (lemon juice, vinega ...

  • CDA SK650 - page 25

    25 intense heat will burn o any splashes. The interior ceiling may need regular cleaning, which should be done with warm water , detergent and a sponge. If the grill is not used regularly , it should be run for 10 minutes every month to burn o any splashes, in order to reduce the risk of fire. PLEASE NO TE: Steam cleaners must not be used to ...

  • CDA SK650 - page 26

    26 • Switch o (or disconnect) the power supply to the appliance. • Contact CD A Customer Care. Installation The appliance can be installed under a worktop or in a wall unit (open at the rear) with the appropriate dimensions for recessed installation. Do not use your appliance immediately after moving it from a cold location, as condensation ...

  • CDA SK650 - page 27

    27 Fig. 12 Fault Code Fault description E1 T emperature sensor faulty E2 T emperature sensor short circuit E4 T emperature sensor circuit failure E8 Latch time ex cessive E64 Mode selector disconnected O THERS The sum of a combination of the above codes ...

  • CDA SK650 - page 28

    28 Mains Electricity Connection W arning! This appliance must be earthed W e recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E. T . and local regulations. This appliance is intended to be connected to fix ed wiring and is not suitable for connection to a 13A ...

  • CDA SK650 - page 29

    29 This appliance is supplied with a 3 core mains cable; the wires are in accordance with the following code: Green and Y ellow = Earth Blue = Neutral Brown = Live Please note: • The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or better rating (i.e. 3x1.5mm 2 , HO5V2V2-F). • The ra ...

  • CDA SK650 - page 30

    30 NO TES: ...

  • CDA SK650 - page 31

    31 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Value Units Model  Identification sk650 Mass  of  the  appliance M 40.5 kg Number  of  cavities 1 Heat  source  per  cavity  (electricity ...

  • CDA SK650 - page 32

    Please contact our Customer Care Department for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu © CDA 2014 ...

Produzent CDA Kategorie Oven

Dokumente, die wir vom Produzenten des Geräts CDA SK650 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen CDA
- Bedienungsanleitungen SK650
- Produktkarten CDA
- Informationsbroschüren
- oder Energieetiketten CDA SK650
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung CDA SK650.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen CDA SK650, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen CDA SK650. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts CDA SK650 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts CDA SK650, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von CDA SK650 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von CDA SK650 verständlich ist.

Eine gänzliche Bedienungsanleitung von CDA sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von CDA SK650 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von CDA SK650 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich CDA SK650, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts CDA SK650 - die uns die ersten Schritte während der Nutzung von CDA SK650 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit CDA SK650 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von CDA SK650 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich CDA SK650?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit CDA SK650 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit CDA SK650 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)