-
Advantek Networks ANS-24RV - page 1
24 Port Fast Ethernet Switch with VLAN and Trunking User Manual Model # ANS-24RV ...
-
Advantek Networks ANS-24RV - page 2
2 FCC Warning This equipment has been tested and found to comply with the limits for a Class A dig ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radi ...
-
Advantek Networks ANS-24RV - page 3
3 Contents 1 Introduction ....................................................................................................... 5 1.1 General Description .................................................................................... ..5 1.2 Product Features..................................................................................... ...
-
Advantek Networks ANS-24RV - page 4
4 2.8.2 Cla ss of Service Configuration ........................................................... 21 2.9 MAC Ad dress .............................................................................................. 22 2.9.1 MAC Address Configuration ............................................................... 22 2.10 Configuration .............. ...
-
Advantek Networks ANS-24RV - page 5
5 1 . I n t r o d u c t i o n 1.1 General Description The device is a powerful, h igh-performance Fast Ethernet swit ch, with all 24 ports capable of 10 or 100Mbps auto-n egotiation operation (Nway) which means the switch co uld automatically negotiate with the connected partn ers on the net work speed and duplex mo de. It is ideal for micro-segmen ...
-
Advantek Networks ANS-24RV - page 6
6 -- Eight Screws *If any of the items is damaged or missing, please contact your retai ler immediately. 1.4 Front panel LED indicators After installing the switch, you can check its st atus from the LED indicators on the front panel shown be low. LED Color Status Indication POWER (PWR) GREEN ON The switch is power on OFF The switch is power off LI ...
-
Advantek Networks ANS-24RV - page 7
7 cable. When using the uplink po rt, you can extend the distance to 100m for linking anothe r switch or hub. 1.9 To prolong the operational life of your units *Never stac k units more than eight hig h if freestanding *Do not place object s on top of any unit or stack *Do not obstruct any vents at the sides of the case ...
-
Advantek Networks ANS-24RV - page 8
8 2. Installing the Fast Ethernet Switch 2.1 Configure system network The switching hub offers a Web ba sed management software to manag e and monitor the switching hub. Before ru nning the management so ftware, you have to configure your system network setup. For Windows 98/98SE and ME, click “ Start Æ Settings Æ Control Panel ”, double clic ...
-
Advantek Networks ANS-24RV - page 9
9 Step 3: Select “ Use the following IP address ”, and enter “ IP address ”, “ Subnet mask ”, and “ Default gate way ” fields, and then click “ OK ”. 2.2 Login the Web Step 1: Enter IP address Æ http://192.168.2.1 in the web browser URL field. Step 2: When Login window pops out, enter “ Username ” & “ Pass w ord ”. ...
-
Advantek Networks ANS-24RV - page 10
10 2.3 The SmartSwitch Home overview The window below shows the Home p age of SmartSwitch: Administrator Æ 1 ) Authentication Configuration 2) System IP configuration ...
-
Advantek Networks ANS-24RV - page 11
11 3) System status 4) Load Default Setting 5) Firmware update Port Management Æ 1) Port Configurati on 2) Port Mirroring 3) Bandwidth Control 4) Broadcast Storm Control VLAN Setting Æ 1) Group VLAN Setting 2) Multi to 1 Setting Trunk Setting Æ Trunk Configuration QoS Setting Æ 1) Priority Mode 2) Class of Service Configuration MAC Address Æ M ...
-
Advantek Networks ANS-24RV - page 12
12 2.4.2 System IP Configuration In this page, you can set and update the IP Address, Subnet Mask, and Gateway setting. After filling up the dat a t hat you want to change, click “ Up date ” to process the dat a changed immediately . 2.4.3 System Status Click on “ System S tatus ” to present the current system statu s on this screen. It wil ...
-
Advantek Networks ANS-24RV - page 13
13 2.4.4 Load Default Setting This option help s you to reset the devic e back to the default setting from the factory . Be aware that the entire configurati on will be reset, the IP address of the device will be set to default setting 192.168.2.1. Just simply click “ Load ” to reset the default setting. After the reset process is completed, yo ...
-
Advantek Networks ANS-24RV - page 14
14 2.4.5 Firmware update Before updating the firmware, you sho uld check whether your mana gement station provides TFTP server and DHCP server . If these 2 services exit on your manag ement station, yo u should disabl e both services by executin g the following procedures: (1) Click “ Control Panel ” Æ “ Sy stem Management T ool ” Æ “ S ...
-
Advantek Networks ANS-24RV - page 15
15 This program can be downloaded from t he web site. http://tf tpd32.jounin.net/ .Y ou don’t need to install this program. T o run TFTPD32 just launch the execut able file tftpd32.exe. Th e configuration procedur e for DHCP/BootP server is illust rated as the following figures. Ste p 1: Click the “ Settings ” item and set base Directory . St ...
-
Advantek Networks ANS-24RV - page 16
16 (5) Press the “ Up date ” button which is shown on the W eb page. After you press the “ up date ” button, the TFTP procedure st arts and the program shows the throughput of the dat a transfer as s hown below . If no throughput can be seen on this program, there may be something wrong with your settings. Please go ba ck to check your sett ...
-
Advantek Networks ANS-24RV - page 17
17 2.5.2 Port Mirroring Port Mirroring is a method of monitoring network traffic that fo rward s a copy of each incoming and/or outgoing p acket from one port of a network switch to another port where the packet can be studi ed. It enables the manager to keep Close track of switch perfo rmance and alter it if necessary . 2.5.3 Bandwidth Control Lim ...
-
Advantek Networks ANS-24RV - page 18
18 TX (T ransmit) Rate : to duplicate the rate of data transmit from the sou rce port and forward to the sniffer port. RX (Receive) Rate: to duplicate the rat e of data that send to the source and forward to the sniffer po rt 2.5.4 Broadcast Storm Control Y ou can enable Broadcast S torm Control to configure the advanced switch function. The value ...
-
Advantek Networks ANS-24RV - page 19
19 2.6 VLAN Setting 2.6.1 Group VLAN Setting This page allows use r to define Virtual LAN (V LAN) membership by group of device’ s ports. Any individual port can be a member of a VLAN group. A VLAN group is basically a broadcast domain, but any port is not limited to belong to only one VLAN group. The forwarding rule is that p ackets from the sou ...
-
Advantek Networks ANS-24RV - page 20
20 2.7 Trunk Setting 2.7.1 Trunk Configuration Port trunk setting. The trunk hash algorithm can select “ Port ID ”, “ Source address ”, “ Destination address ” or “ SD &DA ” ...
-
Advantek Networks ANS-24RV - page 21
21 2.8 QoS Setting In some port s that need to have a high priority to manage the dat a transfer , QoS should be changed. Set the port’ s QoS to high to determine the port will alway s transfer their data first. 2.8.1 Priority Mode Before users do the priority se tting, you have to check the “ Enable High Priority ” box at Class of Service pa ...
-
Advantek Networks ANS-24RV - page 22
22 Default: All ports in T OS priority recognition disabled. VLAN tagging base (T CI) priority recognition: Maki ng a check mark in front of port ID indicates this port is T CI priority enabled. Default: All ports in TCI pri ority recognition disabled. 2.9 MAC Address 2.9.1 MAC Address Configuration This page all ows user define which MAC address c ...
-
Advantek Networks ANS-24RV - page 23
23 2.10 Configuration 2.10.1 Configuration Backup/Re covery This function allows you to backup or re covery the latest switch settings. Just simply enter your password and cli ck “ Up date ” button. ...
-
Advantek Networks ANS-24RV - page 24
24 3. Console User Interface 3.1 Connecting to the Switch Console Port User can configure the switch syste m vi a terminal emulation program through RS-232 port with baud rate 19200-8-n-1. The RS-232 con ne ctor is on the back panel of the switching hub; make sure you connect the other end of se rial port to COM1 of PC. Note: When you use Hype rT e ...
-
Advantek Networks ANS-24RV - page 25
25 S tep 2: The Connection windows will appea r . Enter terminal “ Name ”, select correct icon, and then click “ Ok ” button. S tep 3: Select “ COM1 ” in the “ Connect using ” field and then click “ OK ”. ...
-
Advantek Networks ANS-24RV - page 26
26 S tep 4: Select “ 19200 ” in Bits per second field and cli ck “ Apply ” & “ OK ” buttons to s ave the settings. S tep 5: Reset or pull out the switch power . And then the HyperT erminal screen will appear . W ait for a while for system checking and then press “ s ” to enter the console. Note: If you press other key , you won? ...
-
Advantek Networks ANS-24RV - page 27
27 3.3 Configure Switching Hub via COM1 Port 3.3.1 Switch Main Menu After you enter the Modular Con sole, the Switch Main Menu will appear . 3.3.2 Load Default Setting This page allows user to restore default port settings. ...
-
Advantek Networks ANS-24RV - page 28
28 In the 1 st option to 3 rd option ( 1. Restore switch default setting / 2. Restore IP default Setting / 3. Restore Login defa ult Setting ), just simply press number to restore the default settings. P r e s s ” 4 ’ to enter Modify IP setting screen: ...
Haben Sie eine Frage bezüglich Advantek Networks ANS-24RV?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Advantek Networks ANS-24RV nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Advantek Networks ANS-24RV hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.