Bedienungsanleitung Perle Systems C-100-XXXXX

19 Seiten 0.11 mb
Download

Zur Seite of 19

Summary
  • Perle Systems C-100-XXXXX - page 1

    P/N 5500306-15 Perle Fast Ethernet Media Con verter Modul e Installation Guide C-100-XX XXX Unm anaged Module CM-100-XX XXX Managed Mo dule ...

  • Perle Systems C-100-XXXXX - page 2

    Fast Ethernet Media Converter – Installation Guide 2 Over vie w This docum ent contains instructions n ecessar y for the ins tallation and operation of the Perle Fast Ethernet Media Convert er Module(s) (C-100 and CM-10 0) that are us ed in conju nction with a P erle MCR Ch assis. The C-100 are unmanage d m edia converter m odules, and t he CM-10 ...

  • Perle Systems C-100-XXXXX - page 3

    Fast Ethernet Media Converter – Installation Guide 3 Installatio n The m odule comes equi pped with a ba nk of DIP switches an d jumpers for setting conf iguration. The default DI P switch sett ings (al l switches in the UP posit ion) and jum per settings will work f or most installatio ns.. The f ollowing steps are used to co nfigure the Perle F ...

  • Perle Systems C-100-XXXXX - page 4

    Fast Ethernet Media Converter – Installation Guide 4 Auto-Config Jumper (CM-100 only ) The Auto-Co nfig jum per (J6) is located j ust belo w the Auto-MDIX jumper ( see above). Ref er to the diagram below f or labelling. This jum per only applies to CM-100 m odules. Strapping p ins 1 and 2 of the jum per will set the m odule in SW mode and str app ...

  • Perle Systems C-100-XXXXX - page 5

    Fast Ethernet Media Converter – Installation Guide 5 DIP Switches DIP Switch Settings Auto Negoti ation (Sw itch 1) Switc h Position Mode Up (defau lt) Auto Down Off Auto : In this mode of operation the Me dia Conv erter Module will negotiate Ethernet param eters on th e copper conn ection. T his will ensure the m ost optim al connection param et ...

  • Perle Systems C-100-XXXXX - page 6

    Fast Ethernet Media Converter – Installation Guide 6 Link M ode (Switch 2) Switch Position Mode Up (defau lt) Link Pass- Through Mode Down Standard Mo de Link Pass-T hrough: In this mode, the link state on one connec tion is directly reflecte d throug h the Media Co nverter Mo dule to the ot her connection. If link is lost on one of the connectio ...

  • Perle Systems C-100-XXXXX - page 7

    Fast Ethernet Media Converter – Installation Guide 7 If the Media C onverter has been set to Link Pas s-Thr ough mode, the effec t will be the sam e as FEF, since the link loss on the fiber r eceiver will bring do wn the copp er link, which will in turn c ause the tra nsm it fiber link to be brought d own. Note: If it is required to either gen er ...

  • Perle Systems C-100-XXXXX - page 8

    Fast Ethernet Media Converter – Installation Guide 8 Unused (Sw itch 4) Pause (Sw itch 5) Switch Position Mode Up (defau lt) Enabled Down Disabled Enabled: W hen Auto Neg otiation has been set to Auto (SW 1), the Media Con verter Modul e will use this s etting for its Ethernet param eter negotiation o n the copper connection. Disable: The Media C ...

  • Perle Systems C-100-XXXXX - page 9

    Fast Ethernet Media Converter – Installation Guide 9 Installing or Replacing Media Converter Modules Caution: O bserve electro static dis charge precau tions w hen installing the Media Con verter Module(s) into t he Chassis. Failure to obs erve this caution co uld result in d amage to the Module(s ) and/or chassis. The Perle Me dia Conv erter Mod ...

  • Perle Systems C-100-XXXXX - page 10

    Fast Ethernet Media Converter – Installation Guide 10 7. Rem ove the dust cap f rom the fiber c onnector and connec t the fiber and c opper cabl es. Removing Media Convert Modules 1. Loosen the c aptive reta iner screw on th e front of the Media Converter M odule and ge ntly pull the m odule ou t. 2. If not insert ing a replacem ent Media Co nver ...

  • Perle Systems C-100-XXXXX - page 11

    Fast Ethernet Media Converter – Installation Guide 11 Installing the Simplex Fiber Cable • Locate a 1 00Base-X compliant sim plex (1 stran d) fiber cable with appropr iate connector s. • Connect the fiber cab le from one Media Converter Module to another Medi a Converter/s witch/f iber device. Installing the Copper Cable • Locate 100 Base-T ...

  • Perle Systems C-100-XXXXX - page 12

    Fast Ethernet Media Converter – Installation Guide 12 Operation Status LED The Perle F ast Ethernet M edia Conv erter m odules have three single color s tatus LEDs located on th e face plate of the m odule. PWR - Pow er/Test • On : Power is on, m odule operating norm ally. • Blinking slo wly : the m odule is in loop back m ode. • Blinking q ...

  • Perle Systems C-100-XXXXX - page 13

    Fast Ethernet Media Converter – Installation Guide 13 Other Features Auto-M DIX: Auto-MDIX ( autom atic medium -dependant inter face) detects the signalling on the 100B ASE-T interface to deter mine the t ype of cable connect ed (straight- through or c rossover) a nd automatical ly configures t he conn ection. Error Recov ery: In certain conf igu ...

  • Perle Systems C-100-XXXXX - page 14

    Fast Ethernet Media Converter – Installation Guide 14 Troubleshooting General • Ensure the m odule is corr ectly seated to the bac kplane in the MCR Chass is. The PW R LED should be on solid. • Ensure both devices on either end of the fiber are compatible. If using a sim plex fiber c onnection, e nsure that you have bot h an Upstrea m (U) and ...

  • Perle Systems C-100-XXXXX - page 15

    Fast Ethernet Media Converter – Installation Guide 15 Method 2: The f iber connection ca n also be verified b y configuring the rem ote Media Converter for loopback mode. T he LKF LEDs o n both Media C onverters should be lit. Data sho uld pass through the local con verter, over the fiber conn ection to th e rem ote Media Con verter. At the re m ...

  • Perle Systems C-100-XXXXX - page 16

    Fast Ethernet Media Converter – Installation Guide 16 Technical Specifications Power Inpu t/Consump tion 12V DC / 2.0 W Operating T emperatur e: 0 ° C to 50 ° C (32 ° F to 122 ° F) Storage Tem perature : - 25 ° C to 70 ° C (-13 ° F to 158° F) Operating Hu midity : 5% to 90% (non-condensing) Storage Hum idity : 5% to 95% (non-condensing) O ...

  • Perle Systems C-100-XXXXX - page 17

    Fast Ethernet Media Converter – Installation Guide 17 C-100-S2SC120 CM-100-S2SC120 SM T X: 1550 RX: 1550 Min: 0 Max: 5 Min: -35 Max: -3 35 C-100-S2ST120 CM-100-S2ST120 SM TX: 1550 RX: 1550 Min: 0 Max: 5 Min: -35 Max: 0 35 C-100-S2LC120 CM-100-S2LC120 S M T X: 1550 RX: 1550 Min: 0 Max: 5 Min: -35 Max: -3 35 C-100-S1SC20U CM-100-S1SC20U SM TX: 1310 ...

  • Perle Systems C-100-XXXXX - page 18

    Fast Ethernet Media Converter – Installation Guide 18 Compliance Information FCC This product has been found to comply with the li mits for a Class A digital devi ce, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against har mful interference when the equip ment is operated in a commercial enviro ...

  • Perle Systems C-100-XXXXX - page 19

    Fast Ethernet Media Converter – Installation Guide 19 Warranty / Reg istration Perle’s stan dard Lifetim e Warrant y provides cus tomers with return to f actory repairs f or Perle pro ducts that f ail under the conditions of the warrant y coverage. Det ails can b e found at : http://www.pe rle.com/support_services/warrant y .shtml Contacting Te ...

Produzent Perle Systems Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Perle Systems C-100-XXXXX erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Perle Systems
- Bedienungsanleitungen C-100-XXXXX
- Produktkarten Perle Systems
- Informationsbroschüren
- oder Energieetiketten Perle Systems C-100-XXXXX
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Perle Systems C-100-XXXXX.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Perle Systems C-100-XXXXX, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Perle Systems C-100-XXXXX. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Perle Systems C-100-XXXXX ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Perle Systems C-100-XXXXX, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Perle Systems C-100-XXXXX hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Perle Systems C-100-XXXXX verständlich ist.

Eine gänzliche Bedienungsanleitung von Perle Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Perle Systems C-100-XXXXX bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Perle Systems C-100-XXXXX befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Perle Systems C-100-XXXXX, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Perle Systems C-100-XXXXX - die uns die ersten Schritte während der Nutzung von Perle Systems C-100-XXXXX erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Perle Systems C-100-XXXXX hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Perle Systems C-100-XXXXX im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Perle Systems C-100-XXXXX?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Perle Systems C-100-XXXXX nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Perle Systems C-100-XXXXX hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)