-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 1
Part No. 240612 CATALOG NO. 6000.52-Z Effective: 11-01-01 Replaces: 08-01-01 ® INST ALLA TION AND OPERA TING INSTRUCTIONS Models P-R185A to P-R405A C-R185A to P-R405A Low NOx P-R185AL to P-R405AL C-R185AL to C-R405AL RP2100 SWIMMING POOL and SP A HEA TER This manual should be maintained in legible condition and kept adjacent to the heater or kept ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 2
TO WHOM IT MAY CONCERN: The new Raypak series RP2100 pool heaters have been designed to eliminate the need for conventional heat sinks (high temperature piping). The initial connection to the heater is made with a 2" PVC union adapter to which PVC may then be connected with appropriate cement. This newly authorized piping arrangement is descri ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 3
CONTENTS 3 4 PART ONE OWNER'S OPERATING INSTRUCTIONS 4 SECTION 1 START-UP PROCEDURES 4 Before Start-Up 5 Lighting Instructions & Shut-Off Procedure (Manually Lighted Pilot MV) 6 Operating Instruction & Shut-Off Procedures (Automatically Lighted Pilot IID) 7 After Start-Up 7 SECTION 2 CAUTION 7 SECTION 3 MAINTENANCE & CARE PROCEDURE ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 4
P ART ONE - OWNER'S OPERA TING INSTRUCTIONS FOR YOUR SAFETY - READ BEFORE OPERATING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. SECTION 1 / START-UP PROCEDURES Your Raypak Pool/Spa heater has been designed for years of safe and reliable pool ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 5
4. Push the gas control knob slightly and turn clockwise to "Off". Do not force. 5. Replace heater door panel. 1. Set the thermostat to the lowest setting. 2. Turn On/Off switch to the "Off" position. 3. Remove heater door panel. TO TURN OFF GAS TO APPLIANCE A. This appliance has a pilot that must be lighted by hand. When lighti ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 6
A. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. B. BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS: *Do not try to light a ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 7
AFTER START-UP Feel the inlet and outlet pipes. Outlet pipe should be only slightly warmer than the inlet. It should not be hot. WARNING: Should overheating occur or the gas supply fail to shut off, turn off the manual gas control to the appliance. VISUAL INSPECTION With the heater on, remove the door and make a visual check of the pilot and burner ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 8
4. Make visual check of the burner and pilot flame. Flame pattern on the main burner and pilot is indi- cated in the previous illustration. Yellow flame means restriction of the air openings. Lifting or blowing flame indicates high gas pressure. Low flame means low gas pressure. Should this occur, shut the heater off and contact your gas supplier o ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 9
WINTERIZING THE POOL & SPA HEATER When heaters installed outdoors in freezing climate areas are to be shut down for the winter, observe the following step-by-step procedure: 1. Turn off gas valve, manual gas valve, and electrical supply to the heater. 2. Open drain plug located on the inlet/outlet header, (under water pipes). Remove the heat ex ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 10
12" Minimu m 12" M inimum 4" Minimum HEA TER Sheet Metal 24 Gauge SECTION 3 / INSTALLATION INSTRUCTIONS 10 IMPORTANT NOTICE These instructions are intended for the use of quali- fied personnel only, specifically trained and experienced in the installation of this type of heating equipment and related system components. Installation a ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 11
Heaters must not be installed under an overhang of less than three (3) feet from the top of the heater. Three (3) sides must be open in the area under the overhang. Roof water drainage must be diverted away from the heaters installed under overhangs with the use of gutters. For U.S. installations ,the point from where the flue products exit the hea ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 12
INDOOR HEATER The design is also certified for indoor installation when equipped with the approved draft hood. For Canada , indoor installation is restricted to an enclosure that is not occupied and does not directly communicate with occupied area. Refer to the latest edition of CAN/CGA-B149.1 and B149.2 for specific requirements. Locate heater as ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 13
13 SPECIFICATIONS AND DIMENSIONS *Electrical Connection On Left Side is 19-1/8". a. All Air From Inside The Building: Each opening shall have a minimum net free square inches as noted: Model Square Inches Model Square Inches 185 1 8 1 335 333 265 2 6 4 405 399 b. All Air From Outdoors: When air is supplied directly from outside of building, ea ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 14
VENT PIPING WARNING: Indoor boilers require a drafthood that must be connected to a vent pipe and properly vented to the outside. Failure to follow this procedure can cause fire or fatal carbon monoxide poisoning. Vent piping the same size as the draft hood outlet is recommended, however, when the total vent height is at least ten (10) feet (draft ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 15
Fig. # 8149 NOTE: Do not use teflon tape on gas line pipe thread. A flexible sealant is recommended. A minimum of 7" W.C. and a maximum of 14" W.C. upstream pressure under load, and no load conditions must be provided for natural gas or a minimum of 12" W.C. and a maximum of 14" for propane gas. GAS PRESSURE REGULATOR The gas pr ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 16
Heater must be located so that any water leaks will not damage the structure of adjacent area. PVC pipe may be glued directly into header unions. FLOW RATES MODEL PIPE SIZE MIN.GPM *MAX.GPM 18 5 1-1/4"-1-1/2" - 2 20 125 26 5 1-1/4"-1-1/2" - 2 25 125 33 5 1-1/4"-1-1/2" - 2 35 125 40 5 1-1/4"-1-1/2" - 2 40 125 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 17
17 PRESSURE RELIEF VALVE INSTALLATION To conform to local building codes, it may be necessary to install a pressure relief valve. A 3/4" pressure relief valve having a capacity equal to BTU/HR output of the model to be installed is recommended for this appliance. The maximum acceptable pressure re- lief valve setting is 125 psi. A 3/4" NP ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 18
RP2100+ Heat Exchanger Reversal Procedure (Capron Resin Header Models) 1. Remove right and left side access panels ( Figure 1). 2. Disconnect wires at high limit, AGS (automatic gas shutoff), and pressure switch on the inlet/outlet header ( Figure 2). 3. Electronic Ignition Heaters: Remove the thermostat temperature sensor by loosening the compress ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 19
Fig. #4 Fig. #5 Fig. #3 JACO FITTING BULB & CLIP RE-INSTALLED IN/OUT HEADER ON OPPOSITE SIDE. 19 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 20
ELECTRICAL WIRING NOTE : If it is necessary to replace any of the original wiring, it must be replaced with 105° C wire or its equivalent, and /or 150° C wire or its equivalent as originally built. MILLIVOLT SYSTEM The Millivolt System residential heater is equipped with a self-generating electrical system in which the electric current is provide ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 21
21 WIRING DIAGRAM KEY PINK CONNECTOR BLUE CONNECTOR Fig. # RP8096 *If required by Local Code, install at this location. Fig. #2353 For 120 V input power to the unit, connect the black wire to the “L1” or hot leg of the power supply . Connect the white wire to the “L2” or neutral leg of the power supply . Att ach the wire nut to the red wire ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 22
WIRING DIAGRAM - IID UNITS (atmospheric) 22 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 23
WIRING DIAGRAM - IID UNITS (Low NOx) 23 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 24
Control Panel Mounting Screws (4) Fig. #RP 8267 CONTROLS/ADJUSTMENTS/REPLACEMENTS Temperature Adjust Buttons Mode Button LCD Display Fig. #2000 MILLIVOLT CONTROLS The pool or spa water temperature is controlled by the pool heater thermostat on the upper front panel of the heater. The control center contains an On/Off switch and one or two thermosta ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 25
To adjust the desired pool or spa temperature setting, make sure the control is in the appropriate mode (POOL or SPA) and push the UP or DOWN buttons to get the desired set point temperature. If there is a safety fault, a fault code will be displayed along with a service indication. If the PRS fault code is displayed, it indicates that there is ins ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 26
RP2100 REMOTE CONTROL INSTALLATION CAUTION: Before installing remote controls to the RP2100 Digital Heater, read the following: The Raypak RP 2100 Digital Heater is remote ready in most cases. The digital liquid crystal (LCD) display shows the actual pool temperature, operating status, and service codes (See examples below). The touch pad on the co ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 27
PRESSURE SWITCH The pressure switch, or heater actuator, insures that the heater operates only when the filter pump is in operation. It is located on the inlet/outlet header. It is factory set at 1.75 PSI for deck level installations. When the heater is located below the level of the spa or pool, it may be necessary to reset the pressure switch to ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 28
BURNER DRAWER REMOVAL 1. Shut off main electrical power switch to heater. 2. Shut off gas upstream of heater. 3. Remove front door. 4. Disconnect gas line from gas valve. 5. Remove (2) screws that mount burner tray to unit, and (2) screws that secure gas valve to jacket. 6. Disconnect wires that terminate at gas valve. 7. Slide out burner tray. 8. ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 29
TUBE CLEANING PROCEDURE Establish a regular inspection schedule, frequency depending on local water condition and severity of service. Do not let the tubes clog up solidly. Clean out deposits over 1/16" in thickness. The heater may be cleaned from the return header side, without breaking pipe connections. It is prefer- able, however, to remove ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 30
The Raypak Low Nox Pool Heaters are certified and tested under the ANSI Z21.56.CSA 4.7 Standards for gas fired pool heaters. The heater should be installed to meet all local codes, the latest editions of the National Fuel Gas Code Z223.1 and the National Electrical Code, ANSI/NFPA 70. OPERATION On call for heat, the ignition system, consisting of a ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 31
31 BURNER DRA WER REMOV AL 1. Shut off main electrical power switch to heater . 2. Shut off gas up stream of heater . 3. Remove front door . 4. Disconnect gas line from gas valve. 5. Remove (2) screws that mount burner tray to the base of the unit, and (2) screws that secure gas valve to jacket. 6. Disconnect wires that terminate at gas valve. 7. U ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 32
MECHANICAL (FOR QUALIFIED SERVICE PERSONNEL ONLY) IMPORTANT NOTICE These instructions are primarily intended for the use of qualified personnel specifically trained and experienced in the installation of this type of heating equipment and related system components. Installation and service personnel may be required by some states to be licensed. Pe ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 33
If pilot burner remains lit. Jump across pressure switch terminals If main burner does not fire, remove jumper Check for adequate water flow from filter Replace pressure switch Jump across thermostat If main burner fires, remove jumper If main burner does NOT fire... Jump across each high limit and remove jumper Replace thermostat Replace high limi ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 34
WARNING HIGH VOLTAGE For qualified Technicians ONLY NOTE: Some heaters may be equipped with an ignition module that shuts off pilot gas if pilot fails to light. To reset, interrupt power to heater. Intermittent Pilot System TROUBLESHOOTING HONEYWELL S8600 NOTE:Before troubleshooting, familiarize yourself with the startup and checkout procedure. Che ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 35
35 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 36
SECTION 6/REPLACEMENT PARTS LIST NOTE: To supply the correct part it is important that you state the model number, serial number and type of gas when applicable. Any part returned for replacement under standard company warranties must be properly tagged with RAYPAK return parts tag, completely filled in with the heater serial number, model number, ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 37
37 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 38
38 Fig. #8124 Honeywell MV Fig. #8107 Fig. #9369 13-P 5-P 16-P 15-P 1-P 9-P 3-P Low NOx BURNER TRAY PILOT ASSEMBLIES 14-P 16-P 3-P 7-P 16-P 3-P 17-P Honeywell IID Atmospheric units for units produced prior to 06/01/2000 Honeywell IID Low NOx and Atmospheric units for units produced after to 06/01/2000 Use KIT Number 008155F for Low NOx units Use KI ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 39
39 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 40
40 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 41
41 ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 42
LIMITED WARRANTY RAYPAK RESIDENTIAL SWIMMING POOL AND SPA HEATERS GAS MODELS 185, 265, 335 & 405 MILLIVOLT 185, 265, 335 & 405 ELECTRONIC GENERAL Raypak, Inc. warrants that the cabinet, burner tray (minus controls) and refractory will be free from defects in materials and workmanship under normal use and service for a period of FIVE YEARS F ...
-
Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A - page 43
Raypak, Inc. , 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 FAX (800) 872-9725 Raypak Canada LTD , 2805 Slough Street, Mississauga, Ontario, Canada L4T 1G2 (905) 677-7999 FAX (905) 677-8036 Raypak Australia Pty. Ltd , 7 Geddes St., Mulgrave, Victoria, Australia 3170 (6139) 560 4944 FAX (6139) 560 4974 Litho in U.S.A. www .rayp ak.com ...
Haben Sie eine Frage bezüglich Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Aqua Products RP2100, P-R185A, P-R405A, C-R185A, P-R405A hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.