Bedienungsanleitung Lopi Yankee Bay Pellet Insert

40 Seiten 2.1 mb
Download

Zur Seite of 40

Summary
  • Lopi Yankee Bay Pellet Insert - page 1

    • Masonry Fireplace • Factory Built (Metal) Fireplace • Mobile Home Approved Tested and Listed by Omni-Test Laboratories, Inc. Beaverton, Oregon Report # 028–S–51-2 ASTME-1509 1995, ULCC 1482 Yankee Bay Pellet Insert - - Please read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow t ...

  • Lopi Yankee Bay Pellet Insert - page 2

    2 Introduction Travis Industries 4 0 5 0 5 0 9 1 00-01145 Introduction We welcome you as a new owner of a Yankee Bay pellet heater. In purchasing a Yankee Bay you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics. The Yankee Bay is one of the finest ...

  • Lopi Yankee Bay Pellet Insert - page 3

    Table of Contents 3 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Introduction Introduction ......................................................2 Important Information .........................................2 Safety Precautions Safety Precautions ............................................4 Specifications Heating Specifications .................. ...

  • Lopi Yankee Bay Pellet Insert - page 4

    4 Safety Precautions Travis Industries 4 0 5 0 5 0 9 1 00-01145 • Do not operate the heater if you smell smoke coming from the heater. Turn the P OWER switch to "OFF", monitor your heater, and call your dealer. Ok • Contact your local building officials to obtain a permit and information on any installation restrictions or inspection ...

  • Lopi Yankee Bay Pellet Insert - page 5

    Safety Precautions 5 Travis Industries 4 0 5 0 5 0 9 1 00-01145 • The heater will not operate during a power outage. If a power outage does occur, check the heater for smoke spillage and open a window if any smoke spills into the room. • This heater must be connected to a standard 115 V., 60 Hz grounded electrical outlet. Do not use an adapter ...

  • Lopi Yankee Bay Pellet Insert - page 6

    6 Specifications Travis Industries 4 0 5 0 5 0 9 1 00-01145 Heating Specifications: Approximate Maximum Heating Capacity (in square feet)* ........................................ 800 to 2,250 Burn Rate (Pounds per Hour)** ............................................................................ 1.7 to 5.5 Maximum Burn Time on Low Burn** ....... ...

  • Lopi Yankee Bay Pellet Insert - page 7

    Installation 7 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Before You Begin READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE THIS HEATER. FAILURE TO FOLLOW THE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. Check with local building officials for any permits required for installation of this pellet heater and notify your ...

  • Lopi Yankee Bay Pellet Insert - page 8

    8 Installation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Hopper Extension Set-up This pellet heater has a variable-height hopper. This allows the hopper to be lowered for smaller fireplaces. Follow the instructions below to set the correct hopper extension position. • Determine the correct hopper extension position following the directions below ...

  • Lopi Yankee Bay Pellet Insert - page 9

    Installation 9 Travis Industries 4 0 5 0 5 0 9 1 00-01145 • Remove the correct knock-outs in the hopper walls following the directions below. Use a center-punch (or other suitable tool) to remove the appropriate knock- outs in the hopper walls (punch the holes out from the inside). Make sure to support the hopper walls while removing the knock-ou ...

  • Lopi Yankee Bay Pellet Insert - page 10

    10 Installation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Clearances • Insert must be placed so that no combustibles are within, or can swing within (e.g. drapes, doors), 36" of the front of the heater. • Insert must be placed a minimum 8-3/4" from a side wall (or combustible protruding more than 3/4"). Mantel Requirements • T ...

  • Lopi Yankee Bay Pellet Insert - page 11

    Installation 11 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Venting the Pellet Stove • PELLET VENT MUST MAINTAIN A MINIMUM 3" CLEARANCE TO ANY COMBUSTIBLE (INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER). • DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY OTHER APPLIANCE OR STOVE. • DO NOT INSTALL A FLUE DAMPER IN THE E ...

  • Lopi Yankee Bay Pellet Insert - page 12

    12 Installation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Mobile Home Requirements • Outside air is required (used for combustion) - see the directions below. WARNING: D O NOT INSTALL IN SLEEPING ROOM. CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED. Outside Air (used for combustion) ? ...

  • Lopi Yankee Bay Pellet Insert - page 13

    Installation 13 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Baffle Installation Install the baffles included with the insert (see page 27 for details). Restrictor Adjustment The exhaust restrictor “ fine tunes ” your appliance, ensuring it pulls the correct amount of air through the firebox. Altitude, vent configuration, and other factors make r ...

  • Lopi Yankee Bay Pellet Insert - page 14

    14 Installation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Surround Panel & Circuit Board Installation NOTE : Attach the vent prior to installing the surround panels (& circuit board). a Remove the circuit board from the rear hopper support. Disconnect the wiring harness from the circuit board (see step “ d ” below for a detailed view). ...

  • Lopi Yankee Bay Pellet Insert - page 15

    Installation 15 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Installation into a Masonry Fireplace “ L ” Vent Flex Section Outside air may be drawn from the ash cleanout. “ L ” Vent Storm Collar Vertical Cap Cover Plate (non-combustible) Silicone Seal the cover plate with silicone. HINT: Paint the interior of the fireplace with latex paint to ...

  • Lopi Yankee Bay Pellet Insert - page 16

    16 Installation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Installation into a Factory Built (Metal) Fireplace “L” Vent Flex Section HINT: Paint the interior of the fireplace with latex paint to prevent fireplace odors from entering the home. “L” Vent Storm Collar Vertical Cap Cover Plate (non-combustible) Silicone Seal the cover plate with ...

  • Lopi Yankee Bay Pellet Insert - page 17

    Operation 17 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Safety Notice • Read this entire manual (especially the "Safety Precautions" on pages 4 and 5) before using this heater. Failure to follow the instructions may result in property damage, bodily injury, or even death. • Do not unplug the heater to turn it off. This heater relies u ...

  • Lopi Yankee Bay Pellet Insert - page 18

    18 Operation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Loading Pellets Lift the hopper lid to its vertical position. Pour pellets into the hopper until full. NOTE: The hopper holds approximately 48 to 88 pounds of pellets (depending upon hopper set-up). The front edge of the hopper lid becomes very hot, do not touch the area below the handle. Make ...

  • Lopi Yankee Bay Pellet Insert - page 19

    Operation 19 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Manual Mode Manual mode requires the user to turn the heater on and off manually. To Start Press the "Manual Start" button. That's it. The stove automatically goes to a medium burn rate and high fan while the igniter starts the fire burning within 10 minutes. During this period ...

  • Lopi Yankee Bay Pellet Insert - page 20

    20 Operation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Auto Mode Auto mode allows you to use a thermostat to control room temperature. The stove automatically turns on when the temperature drops below the thermostat setting. Once the stove reaches operating temperature, the stove then runs at the heat output setting selected. To Adjust Room Temper ...

  • Lopi Yankee Bay Pellet Insert - page 21

    Operation 21 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Restrictor Adjustment The exhaust restrictor “ fine tunes ” your appliance, adjusting the amount of air flowing to the flame. NOTE : the optimal restrictor position will vary over time as soot builds up inside the exhaust system. Not Enough Air: If clinkers develop or the flame appears laz ...

  • Lopi Yankee Bay Pellet Insert - page 22

    22 Operation Travis Industries 4 0 5 0 5 0 9 1 00-01145 Start-Up Sequence This stove utilizes a start-up sequence whenever the mode switch is changed or the heater is started when cold. This is to ensure proper operation through all possible settings and operational states (hot or cold, pellets burning or not burning, etc.). This sequence over-ride ...

  • Lopi Yankee Bay Pellet Insert - page 23

    Maintenance 23 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Daily Maintenance (whenever using the heater) Inspect the Burn When burning on high, the flames should be bright orange with embers jumping from the firepot. NOTE : the optimal restrictor position will vary over time as soot builds up inside the exhaust system. See "Restrictor Adjustmen ...

  • Lopi Yankee Bay Pellet Insert - page 24

    24 Maintenance Travis Industries 4 0 5 0 5 0 9 1 00-01145 Daily Maintenance (whenever using the heater) - Continued Check Firepot for Clinkers If the flames seem to be coming only from the sides, or are orange/black, turn the heater off and check for clinkers. The most likely causes are: • Restrictor needs adjustment (see “ Restrictor Adjustmen ...

  • Lopi Yankee Bay Pellet Insert - page 25

    Maintenance 25 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Bi-Weekly Maintenance (or every 10 bags of pellets) Clean the Heat Exchange Tubes With the door closed, insert the included tool into the hole on the heat exchanger cleaning rod. Move the heat exchange cleaner up and down several times. Keep the door closed so the flyash does not enter the r ...

  • Lopi Yankee Bay Pellet Insert - page 26

    26 Maintenance Travis Industries 4 0 5 0 5 0 9 1 00-01145 Bi-Weekly Maintenance (or every 10 bags of pellets) - Continued Opening The Door Swing open this panel to access the door latch (use the tool if necessary). Phillips Screwdriver With the pawl free of the bracket, the door may be swung open. When securing the door, make sure the pawl fits ove ...

  • Lopi Yankee Bay Pellet Insert - page 27

    Maintenance 27 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Bi-Weekly Maintenance (or every 10 bags of pellets) - Continued Check Baffles, Ashbox, Ashpan, Dispose Ash If Necessary Removing the Ashpan The ashpan slides out from under the firebox. NOTE : When replacing the ash pan make sure it is pushed all the way in. Ashpan WARNING: The front of the ...

  • Lopi Yankee Bay Pellet Insert - page 28

    28 Maintenance Travis Industries 4 0 5 0 5 0 9 1 00-01145 Bi-Weekly Maintenance (or every 10 bags of pellets) - Continued Sweep Ash Into Ashpan HINT: The more often you clean out the flyash, the more efficient your heater will burn. NOTE: Remove the ashbox prior to conducting the service below. Swing the side ash trap door up. Lift it up and away f ...

  • Lopi Yankee Bay Pellet Insert - page 29

    Maintenance 29 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Yearly Maintenance (or every two tons) WARNING: Disconnect the power cord prior to conducting service. The following section details extensive maintenance procedures. We strongly suggest these items be carried out by a trained service technician, possibly by a service agreement set up with y ...

  • Lopi Yankee Bay Pellet Insert - page 30

    30 Maintenance Travis Industries 4 0 5 0 5 0 9 1 00-01145 Yearly Maintenance (or every two tons) - Continued Clean the Exhaust Blower (make sure the heater is cool and unplugged) a Remove the surround panels and access the left side of the heater. Remove the shroud covering the blower motor. Remove the six screws holding the exhaust blower motor in ...

  • Lopi Yankee Bay Pellet Insert - page 31

    Maintenance 31 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Yearly Maintenance (or every two tons) - Continued Door Seal ! Air leaks into the firebox will decrease the stove's performance greatly, leading to excessive sooting, inefficient burning, and perhaps a malfunction. • The door gasket must contact the entire perimeter of the door and cr ...

  • Lopi Yankee Bay Pellet Insert - page 32

    32 Maintenance Travis Industries 4 0 5 0 5 0 9 1 00-01145 Adjusting the Door Hinge and Latch • The door hinge and door latches may be adjusted to pull the door closer to the body. The illustration below details how to adjust these components. NOTE: Make sure to read the section "Door Alignment" on the previous page before adjusting the ...

  • Lopi Yankee Bay Pellet Insert - page 33

    Maintenance 33 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Check for Air Leaks Around the Door, Glass, and Ashpan ! Air leaks into the firebox will decrease the stove's performance greatly, leading to excessive sooting, inefficient burning, and perhaps a malfunction. • Inspect the door gasket to make sure it is fully attached. Use stove gaske ...

  • Lopi Yankee Bay Pellet Insert - page 34

    34 Normal Operating Sounds Travis Industries 4 0 5 0 5 0 9 1 00-01145 Auger Motor When feeding pellets, you may hear the intermittent buzz of this motor running. Convection Fan The modern high efficiency fan may produce a low hum, particularly on "HIGH". This sound will change as the FAN dial is turned. Heat Exchanger Tubes You may hear t ...

  • Lopi Yankee Bay Pellet Insert - page 35

    Safety Label 35 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Minimum Clearance to Combustible Materials (Measured from insert top) Adjacent Sidewall A 8.75 in Mantel B 11.5 in T op Facing C 6.25 in Side Facing D 7 in W ARNING - DO NOT REMOVE OR COVER THIS LABEL Listed Pelletized Solid Fuel Burning Appliance For use in masonry or factory built (ZC) fi ...

  • Lopi Yankee Bay Pellet Insert - page 36

    36 Limited 7 Year Warranty Travis Industries 4 0 5 0 5 0 9 1 00-01145 To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275. TRAVIS INDUSTRIES, INC. warrants this gas a ...

  • Lopi Yankee Bay Pellet Insert - page 37

    Optional Equipment 37 Travis Industries 4 0 5 0 5 0 9 1 00-01145 Thermostat (Part # 99300650) ! Do not connect 120 VAC to the thermostat circuit of this heater (do not use a household thermostat used for a wall-board or other electical heater). 1 Attach the thermostat wire to the circuit board (see the illustration to the right). Route the wire thr ...

  • Lopi Yankee Bay Pellet Insert - page 38

    38 Optional Equipment Travis Industries 4 0 5 0 5 0 9 1 00-01145 Remote Thermostat (Part # 99300653) • Follow the instructions included with the remote thermostat for installation and operation. Optional Log (Part # 98900126) ! Make sure the heater has fully cooled before installation. 1 Open the door (see the instructions included with the owner ...

  • Lopi Yankee Bay Pellet Insert - page 39

    Optional Equipment 39 Travis Industries 4 0 5 0 5 0 9 1 00-01145 ZC Kit (99200149) The optional zc kit allows this insert to be directly into the framing of a house or mobile home. See the kit for installation details. Floor Protection Wall Thimble (note 3” clearance between vent and combustibles) 12” Minimum Enclosure Height (measure from top ...

  • Lopi Yankee Bay Pellet Insert - page 40

    40 Index Travis Industries 4 0 5 0 5 0 9 1 00-01145 Adjusting the Fan Speed ......................................2 1 Air Leaks ..........................................................3 1 Ashpan (Opening and Disposing Ashes) .................2 7 AUGER ON Light ................................................2 1 Auto Mode ......................... ...

Produzent Lopi Kategorie Indoor Fireplace

Dokumente, die wir vom Produzenten des Geräts Lopi Yankee Bay Pellet Insert erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Lopi
- Bedienungsanleitungen Yankee Bay Pellet Insert
- Produktkarten Lopi
- Informationsbroschüren
- oder Energieetiketten Lopi Yankee Bay Pellet Insert
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Lopi Yankee Bay Pellet Insert.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Lopi Yankee Bay Pellet Insert, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Lopi Yankee Bay Pellet Insert. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Lopi Yankee Bay Pellet Insert ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Lopi Yankee Bay Pellet Insert, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Lopi Yankee Bay Pellet Insert hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Lopi Yankee Bay Pellet Insert verständlich ist.

Eine gänzliche Bedienungsanleitung von Lopi sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Lopi Yankee Bay Pellet Insert bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Lopi Yankee Bay Pellet Insert befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Lopi Yankee Bay Pellet Insert, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Lopi Yankee Bay Pellet Insert - die uns die ersten Schritte während der Nutzung von Lopi Yankee Bay Pellet Insert erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Lopi Yankee Bay Pellet Insert hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Lopi Yankee Bay Pellet Insert im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Lopi Yankee Bay Pellet Insert?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Lopi Yankee Bay Pellet Insert nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Lopi Yankee Bay Pellet Insert hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)