-
DigiPower ePowerSwitch - page 1
eP o w erSwitch (iSWIT CH) User ’ s Manual 20020925 Rev4 ...
-
DigiPower ePowerSwitch - page 2
2 T able of Contents W a r n i n g s 3 Quick Install Procedure 4 Introduction 7 Remote Power Manager (iSwitch) Features 7 iSwitch Package 7 Setup Procedure 8 1. Setup via the USB Port 8 2. Setup via the Serial Port 18 3. Setup via the Ethernet Por t 25 T elnet Configuration 26 Web-Based Configuration 31 Firmware Upgrade Procedures 39 T elephone Acc ...
-
DigiPower ePowerSwitch - page 3
3 NOTICE: This equipment has been tested and found to comply with the limits for a “Class B digital device, pursuant to Par t 15 of the FCC rules. These limits are designe d to provide reas onable protec tion agains t harmful inter ference when the equipmen t is operated in a co mmercial environ ment. This equipment gen erates, uses and c an radi ...
-
DigiPower ePowerSwitch - page 4
4 Quick Install Procedure This section will guide you through the quick installati on of the iSwitch. 1. Install m ounting bracket s: pa ge 4. 2. Install all input and outp ut conn ection s: p a ges 5 an d 6. 3. Progra m you IP address: page 9. For USB setu p: a) Insert Driver Setup Diskette in floppy drive. b) Run Setup.exe from flop py drive. c) ...
-
DigiPower ePowerSwitch - page 5
5 iSwitch-Front Panel Setup via USB Port Setup via RS232 Port Setup via Ethernet Port Receptacle Control S tatus LED (Green) Receptacle S tatus LED (Red) Active Module LED (Y ellow) Moment ary sw itch fo r Recept acle Master Power Switch iLink Port is for Daisy Chai ni ng External Modem is required for Page r Function Ring On/Reset Port – Connect ...
-
DigiPower ePowerSwitch - page 6
6 Receptacle S t atus LED (Red) : When the LED is illuminated the recept acle is on and prov iding AC Power . When the L ED is off the receptacle is not pr oviding AC Power . Receptacle Control Status LED (Green): When the control LED is illuminated, the momentary switch is disabled an d the output rec eptacle is programmed for remote control. When ...
-
DigiPower ePowerSwitch - page 7
7 Introduction The Remote Pow er Manager (iSw itch) is a networ k-mana geable, intelligent power co ntrol unit designed to provide control of pow er for up to eight electrical de vices. NOTE: If the iSwitch is turned off by the mas t er power switch, you have to wait approx imately thirty seconds before restarting the iSwi tch to allow the iSwitch ...
-
DigiPower ePowerSwitch - page 8
8 Setup Procedure This section describ es the setup pro cedures of the iS wit ch when you connect it to the network. NOTE: The minimum requirement to ope rate the iSw itc h is to set the IP address. There are four different ways to setup the iSwitch. 1. Setup the IP Addr ess via the USB port (s oftware included). R equires Window s 98 or higher . 2 ...
-
DigiPower ePowerSwitch - page 9
9 8.The Hardware wizard will guide you through installing the USB Driver . Click Next. 9. Hardware wizard will search for the best USB Driver . Click Next. 10. Check, S p ecify a location. Click Browse. ...
-
DigiPower ePowerSwitch - page 10
10 1 1. Open the app ropriate 3½ ″ Floppy Drive. Open th e USB folder . Open the Driver folder . Click OK . 12. Windows will search for the new USB Driver . Click Next. 13. Windows h as found the U SB Driver for the U SB device. Click Nex t. ...
-
DigiPower ePowerSwitch - page 11
11 14. Windows h as found the b es t Driver for this USB device. Click Nex t. 15. Windows is co pying the US B Driver files to your “C:” drive. Click Nex t 16.Windows is finished installing the USB Driver . Click Finish. T o your “C:” drive. Click Next ...
-
DigiPower ePowerSwitch - page 12
12 17. On the Deskt op, right click “My Compu ter”. Open Prop erties. 18. Open the De vice Manager . W ait for approximatel y 30 seconds f or the “Huma n Interface Device” t o appear . Open the Human Interface Device. Click on “Usb- interface power device”. Click OK. 19. Open Windows Explo rer . Open the appropriate 3½ ″ Floppy Drive ...
-
DigiPower ePowerSwitch - page 13
13 21. This is the Power Device Configuration T ool sc reen. On the T oo lbar open Configuratio n. Then open System. 22. This is the System Par ameter Configuration screen fill in all the information: th e IP Address, the Subne t Mask, the Default Rout e (Gateway) and the DNS Server . Use the T ab key to move from one field to the next field. Then ...
-
DigiPower ePowerSwitch - page 14
14 23. This is the Power Device Configuration T ool screen. Af t er you have entered in all o f the pertinent information , you have to Up da te and Rest art to save all the information that was entered into the System Parameter Configuration screen. The Update and Restart icon (with the red arrow) is right be neath the “Device” drop down menu. ...
-
DigiPower ePowerSwitch - page 15
15 25. This is the Power Device Configura tion screen. Click Y es to Update the Po wer Device. 26. This is the Device Parameter Transmitting screen. The Powe r Device is being Up dated. ...
-
DigiPower ePowerSwitch - page 16
16 27. The Powe r Device h as been success fully updated. Clic k OK. 28. The Power Devic e has to be Rest ar t ed . Cli c k Y es. 29. The USB Setup Proced ure is complete . The iSwitch is fully operational. Unpl ug the USB Cab le from the ...
-
DigiPower ePowerSwitch - page 17
17 iSwitch and fr om the computer. Plug the Ethernet Cable into the iSwitch an d after about thirty seco nds the Link LED will start blinking, now you can communicate wi th the iSwitch. The Ping command is supported at this time. S tartup a Browser and type in the IP Address. The defau lt p assword is admin (lower cas e). Go to the section in the U ...
-
DigiPower ePowerSwitch - page 18
18 7. Connect using the appro priate Com port. Click OK 8. Configure the port s ettings. B its per second: “1 15200”, D ata bits: “8”, P arity: “None” , S top bits: “1”, F low control: “None”. Clic k OK 9. On the T oolbar open the File men u, and then open Prop erties. ...
-
DigiPower ePowerSwitch - page 19
19 10. Open the Settings T ab. Function, arrow and c trl keys act as: T erminal Keys, Backsp ace key sends: C rtl+H, Emulation: VT100, T eln et terminal: VT100, B ackscroll buf fer lines: 500. Click OK. 11. Plug the iSwitch’s power cord into the AC outlet and turn the iSwitch on. 12. When th e message “Pr ess ‘/’ key within 5 seconds to ent ...
-
DigiPower ePowerSwitch - page 20
20 14. Ctrl-Z moves the curs or down and C trl-W moves the cur sor up. Pick Networ k, then hit enter . 15. Enter in the IP Address , the Gateway Address, the Subnet Mas k and the DNS (a ll required) . Hit the “Escape” key to return to the main menu. ...
-
DigiPower ePowerSwitch - page 21
21 16. Arrow down to PPP Config and hit enter . Enter in the ISP dial number , the ISP account/password an d the enable/dis able dial-out in terface (no t required). H it the “Escape” key to return to the ma in menu. 17. Arrow down to Mail and h it enter . Enter in the SMTP Server (not required). The user can add or delete email addresses. Hit ...
-
DigiPower ePowerSwitch - page 22
22 18. Arrow down to T rap and hit enter . This screen allows the user to send T raps about the UPS to ten IP Address es (not require d). Also, you ma y determine the s everity levels and w hat type of access , read only or read and write, to assign to a particular IP manager . Hit the “Escape” key to return to the main menu. 19. Once you have ...
-
DigiPower ePowerSwitch - page 23
23 20. After rebooting the system, the new se ttings will be activated. Reboot (y/n )? Hit the y key then hit enter . Once the syste m has rebooted, c ursor dow n to Exit then hit enter . 21. The Serial Setup Proc edure is complete. The iSwitch is fully operational. Unplug the DB9 female-to-female Serial Cable from t he iSwitch and from the comp ut ...
-
DigiPower ePowerSwitch - page 24
24 6. This is an example. At the MS-DOS Prompt type: arp –s 192.166.7.19 52- 54-4c-19 -ad-90. Then hit enter . The first string is the IP Address ; the second strin g is the MAC Address (whic h can be found on the front of the iSwitch). 7. At the MS-DOS pr ompt type: route add 192.1 66.7.19 210.67.4.155. Then hit enter . The first string is the I ...
-
DigiPower ePowerSwitch - page 25
25 T elnet Configuration This section will guide you thro ugh finishing the configuration of the iSwitch using T elnet. NOTE: Y ou must complete the appropriate Set up Pr oced ure before procee ding with the T elnet Configuratio n. NOTE: Y ou must ha ve given the iSwitc h an IP Addr ess. NOTE: The connection by telnet client limit s only 2 users. N ...
-
DigiPower ePowerSwitch - page 26
26 4. Pick Ne twork, the n hit enter . 5. Pick IP , then h it enter . Input your IP Addre ss, Gateway Address, Subnet Ma sk and the DN S (all required) . Then hit the left arrow key to exit to the main menu. ...
-
DigiPower ePowerSwitch - page 27
27 6. Arrow dow n to PPP Config and hit enter . Enter in the ISP dial number , the ISP account/passwor d and the enable/d isable dial-ou t interface (not require d). Hit the left arrow key to retu rn to the main menu. 7. Arrow d own to Mail and hit enter. Enter in the SMTP Server (not required ). The user can add or delete email addresse s. Hit the ...
-
DigiPower ePowerSwitch - page 28
28 read and write, to assign to a particular IP manager . Hit the left arrow key to return to the main menu. 9. Once you have finished with the entire configuration, arr ow down to Save_R estart and hit enter . Make sure you want to overwr ite the old settings (y/n)? Hit the y key , then hit en ter . ...
-
DigiPower ePowerSwitch - page 29
29 10. After rebooting the system, the new settings will be activated. Reboot (y /n)? Hit the y key then hit enter . 1 1. The iSwitch has rebooted to activate the new settin gs. Clic k OK. Arrow down to exit then hit enter . 12. At the MS-DOS Prompt type exit, the n hit enter . 13. The T elnet Configura tion is complete. The iSwitch is fully operat ...
-
DigiPower ePowerSwitch - page 30
30 W eb-Based Configuration This section will guid e you through the Web-Based-C onfiguration and the Web Pages of the Remote Power Manager (iSw itch). NOTE: Y ou must complete the appropriate Setu p Procedures before proc eeding with the Web-Based- Configuration. The Ethernet c able is conne cted to the iSwitc h and the iSwitch is on. 1. S t artup ...
-
DigiPower ePowerSwitch - page 31
31 4. This is the scre en where yo u can set the Network parameters. Af ter you have finished filling in all of the information, click Save. BOOT MODE: iSwitch support DHCP , BOOTP and FIXED IP ...
-
DigiPower ePowerSwitch - page 32
32 5. The PPP connection is useful if it is not possible to mak e a direct network connection to the iSwitch. An exter nal modem is needed to connect to the front serial port of the iSwitch. The iSwitch support two w ays using modem to co nnect direct ly . ISP After dialing in t he remote user must hang up after the third ring. Based on the infor m ...
-
DigiPower ePowerSwitch - page 33
33 6. This is the screen where you set the Date and T ime. After you have finished filling in the information, click Save. 7. This is the screen wher e you can change th e Adm inistrator ’s Name and Password . After you have finished filling in the information, click S ave. NOTE: The Supervisor ’s name and passwor d can be from 1 to 19 digits. ...
-
DigiPower ePowerSwitch - page 34
34 8. This is the screen wher e the administrator can enable the application p rogram inter face to certa in users. Afte r you have finished filling in the information, click Save. (Optional) 9. This is the screen wher e the administrator can give certain rights to certain users . After you have finished filling in the information, click Save. 10. ...
-
DigiPower ePowerSwitch - page 35
35 1 1. After filling in all of the information be sure to Save and Restart before exiting the program. iSw itch 12. This screen allows the user to see the status of the iSwitch. The user can control each receptacle individu ally or all of them at the same time. The iSwitch has to be setup in the remote mode to control the receptacles via the Inter ...
-
DigiPower ePowerSwitch - page 36
36 13. a. ID Address Configurat ion and Identification: Since 16 iSWITCHs can be daisy chained togethe r to share one CIC , each unit can be individually named. b. Name: The name of each outlet c an be labeled to wh atever yo u like it to be called (i.e. server1, DSL modem or webser ver1). c. Pow er Resume Delay: The power resu me delay is convenie ...
-
DigiPower ePowerSwitch - page 37
37 14.This screen allows the User to schedule daily/wee kly shutdowns and r estarts of individu a l rece pt acles (b e sure to check the appropriat e box). The safe s hutdown is de dicated to Microsoft Windows NT (4.0, 2000, works tation and server ). Click on the correspond ing outlet to enable the safe shutdown feature. The safe shutdown feature ...
-
DigiPower ePowerSwitch - page 38
38 a. Pager Input the code defined by user himself to Alarm-Add and Alarm-Remove. b. Broadcast It must run an applicatio n in the client to receive this broadcast messa ge. c. Logging Enable the event lo gging function. ...
-
DigiPower ePowerSwitch - page 39
39 d. T rap Set the SNMP trap. e. Mail Send the event to the user pre-set email account . ...
-
DigiPower ePowerSwitch - page 40
40 16. T h is screen allows t he user to check th e iSwitch event log. The Web-Based Configu ration is comple te. The iSwitch is fully oper ational. Firmware Upgr ade Procedures Firmware Upgrade via TFTP With a Web browser , click on “Software upgrade” , input TFTP server ’s IP address and go. Make sure that the firmware file (For example: up ...
-
DigiPower ePowerSwitch - page 41
41 3. Once the messag e “Ch eck u- dram” appea rs hit the “c” key . Then at the cursor type “u p a ll” then hit enter . Once the User hits enter , you h ave approximately thirty s econds to complete the next four step s. 4. Go to the tool bar and select T ransfer . Open S end File. ...
-
DigiPower ePowerSwitch - page 42
42 5.Select “X modem” under Protocol. 6. Click Bro wse. Look in the location where the Firmware upgra de software is located. Select the File n ame: “test.bin” and c lick open. ...
-
DigiPower ePowerSwitch - page 43
43 7. Click S end. 8. The Firmware upgrade will take approximately eight minutes to comple te. ...
-
DigiPower ePowerSwitch - page 44
44 9. The Firmware upgrade is complete. NOTE: The user has to reconfigure all of th e settings after the Firmware u pgrade is complete, becaus e all of the user ’s settings will default to the original default s ettings. ...
-
DigiPower ePowerSwitch - page 45
45 T elephone Access Interface 1. Dial up the iSwitch. 2. After three rings the iSwitch will re spond by sending out thre e short beeps to the caller . Then the iSwitch waits for the user to ente r the passwo rd. 3. The user ente rs an acce ss p assword (def au lt p assword is 12345 67 89 # ). 4. The iSwitch will send out three short beeps to confi ...
-
DigiPower ePowerSwitch - page 46
46 Daisy Chaining The Remote Pow er Manager (iSw itch) can be Da isy Chained up to a maximum of sixteen units. Each iSwitch in the Daisy Chain must have its own unique identific ation number . The default ID# is “0 “. The first iSwitch must have the Internet Power Ma nagement Car d install and must be configur ed before you ca n begin Daisy Cha ...
-
DigiPower ePowerSwitch - page 47
47 16. Plug the third iSwitch's power cord into utility power . 17. Turn the master power switch on. 18. Configure the third iSwitch's ID numbe r (each iSwitc h must have it's own u nique ID#, the defa ult ID# is "0"). 19. If there are only three RPMs required fo r this applicat ion, then this completes th e Daisy Chaining ...
-
DigiPower ePowerSwitch - page 48
48 T roubleshooting Problem: The TES (T erminal Emula tion Software) does not d isplay anything. Solution: Make sure the TES’s communication parameters are corr ec t. They sho uld be 1 15200-baud rate, no parity , 8-data bits, and 1 stop bit. The cable is a DB9 Fe male-to-Female serial cable. Problem: The NMS c annot ping the Remote Po wer Mana g ...
-
DigiPower ePowerSwitch - page 49
49 Appendix This section discusses : Communities, Ga teways, IP Addres ses, and Sub ne t masking. Communities A commu nity is a string of printable ASCII characte rs that ide ntifies a user group w ith the same acces s privilege s. For example, a comm on community name is “public.” For security pu rposes, the SNMP agent validates r equests befo ...
-
DigiPower ePowerSwitch - page 50
50 Subnetting and Subnet Masks Subnetting divides a network addr ess into su b-netwo rk address es to accommo date more tha n one physical network on a logi ca l network. For example: A Class B company has 100 LANs (Loc al Area Networks) with 100 to 200 node s on each LAN. T o classify th e nodes by its LANs on one main network , this company segme ...
-
DigiPower ePowerSwitch - page 51
51 Glossary The Glossary section define s the terms used in the Comput er Interface C ard (CIC) -MP enviro nment. Agent Imp lemented SNMP applicatio ns in netw ork eleme nts (hosts). Agents perform the network man agement’s functions as requested by the n etwork adminis trator from an NMS. Dry Closure Input Non-powered cont act type input s—swi ...
-
DigiPower ePowerSwitch - page 52
52 TES T erminal Emulation Software— Commun ications prog ram to transform a pe rsonal computer into a terminal for the purpose of da ta commu nications. TFTP Serv er T rivial File T ransfer Protocol Se rver— A host to provide services according to TFTP; a TCP/IP standard protocol for f ile transfer with minimal cap ability and overhead depe nd ...
Haben Sie eine Frage bezüglich DigiPower ePowerSwitch?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit DigiPower ePowerSwitch nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit DigiPower ePowerSwitch hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.