Bedienungsanleitung Black Box IC107A-R3

20 Seiten 0.18 mb
Download

Zur Seite of 20

Summary
  • Black Box IC107A-R3 - page 1

    CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500 ) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail: info@blackbox.com DECEMBER ...

  • Black Box IC107A-R3 - page 2

    1 FCC/IC RFI ST A TEMENTS, DECLARA TION OF CONFORMITY FEDERAL COMMUNICA TIONS COMMISSION AND INDUSTR Y CANADA RADIO-FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interf ...

  • Black Box IC107A-R3 - page 3

    2 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY ST A TEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia fu ...

  • Black Box IC107A-R3 - page 4

    3 NOM ST A TEMENT , TRADEMARKS 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptá ...

  • Black Box IC107A-R3 - page 5

    4 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) Contents Chapter Page 1. Specifications ............................................................................................. 5 2. Introduction ............................................................................................... 7 3. Configuration ................................. ...

  • Black Box IC107A-R3 - page 6

    5 CHAPTER 1: Specifications 1. Specifications Compliance: CE; FCC Part 15 Subpart B Class A, IC Class/classe A Interfaces: EIA/TIA RS-232, DTE or DCE (user-selectable); EIA/TIA RS-422/485 Protocol: Asynchronous Data Rate: Transparent to data rates up to 64 kbps Data Format: Transparent to data format Flow Control: Transparent to software flow contr ...

  • Black Box IC107A-R3 - page 7

    6 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) Temperature Tolerance: Operating: 32 to 122˚F (0 to 50˚C) Storage: –4 to +158˚F (–20 to +70˚C) Humidity Tolerance: Up to 95% noncondensing MTBF: 200,000 hours Power: IC107A-R3 and IC107AE-R3: From utility-power (mains) outlet, through external power supply with detachable region-specific inp ...

  • Black Box IC107A-R3 - page 8

    7 CHAPTER 2: Introduction 2. Introduction The RS-232 ↔ RS-422/485 Converter (Data Only) allows your RS-232 and RS-422/485 equipment to communicate with each other. It operates in full-duplex mode over 4-wire lines. A four-wire terminal block on the RS-422/485 port makes installation easy. And this interface converter is flexible: it can work in e ...

  • Black Box IC107A-R3 - page 9

    8 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) 3. Configuration Here’s how to configure the RS-232 ↔ RS-422/485 Converter (Data Only) for your application (refer to Figure 3-1 on the next page for the location of components on the circuit board): CAUTION! The Converter’s circuit board can be damaged by static electricity, so take every rea ...

  • Black Box IC107A-R3 - page 10

    9 CHAPTER 3: Configuration 5. Normally, the Converter’s frame ground is isolated from its RS-232 signal ground. But if you want to connect frame ground to signal ground, you’ll need to solder a 100-ohm, 500-mW resistor to the terminals of location W7. (You could also use a wire jumper, but you’d need to make sure that any ground-loop currents ...

  • Black Box IC107A-R3 - page 11

    10 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) 4. Installation To install your RS-232 ↔ RS-422/485 Converter (Data Only) system, take these steps, making sure that the Converter and your devices are powered OFF: 1. Run an RS-232 cable from your RS-232 device to the Converter’s DB25 female RS-232 port. 2. Run a 4-wire cable from your RS-422 ...

  • Black Box IC107A-R3 - page 12

    11 CHAPTER 5: Operation 5. Operation 5.1 RS-232 Circuitry The RS-232 side of the RS-232 ↔ RS-422/485 Converter (Data Only) is composed of the RS-232 drivers and receivers, the delay circuitry, and other circuitry necessary to operate the RS-232 control lines. Data traveling from the RS-232 interface to the RS-422/485 interface: When the RS-232 po ...

  • Black Box IC107A-R3 - page 13

    12 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) Figure 5-1. Block diagram of Converter functions in DCE mode. Figure 5-2. Block diagram of Converter functions in DTE mode. RS-232 side RS-232 side RS-422/485 side RS-422/485 side ...

  • Black Box IC107A-R3 - page 14

    13 CHAPTER 5: Operation 5.2 RS-422/485 Circuitry The RS-422/485 side of the Converter is made up of the driver, receiver, and line- termination networks. As described in Chapter 3 , you can use switch S2 to either connect the receiver’s termination network to the line (terminate the RS-422/485 port) or leave it unconnected (unterminated). Having ...

  • Black Box IC107A-R3 - page 15

    14 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) 6. T roubleshooting 6.1 Calling Black Box If you determine that your RS-232 ↔ RS-422/485 Converter (Data Only) is malfunctioning, do not attempt to alter or repair the unit . It has no user-serviceable components. Contact Black Box Technical Support at 724-746-5500. Before you do, make a record o ...

  • Black Box IC107A-R3 - page 16

    15 APPENDIX: Pinouts Appendix: Pinouts T able A-1. Pinning of the RS-232 connector (DB25 female). Pin Number and Signal Function Pin1 — Frame Ground Connects the Converter’s frame ground to the frame ground of the RS-232 device. Pin 2 — TD When the Converter is set to DCE, data is received on Pin 2 and the TX LED lights up when Pin 2 is a “ ...

  • Black Box IC107A-R3 - page 17

    16 RS-232 ↔ RS-422/485 CONVER TER (DA T A ONL Y) T able A-2. Pinning of the RS-422/485 connector (4-position ter minal block). Pin/Signal Function TXA and TXB Data received by the Converter from the RS-232 port is transmitted out of the unit over twisted-pair wires using these two outputs. The “TX” LED indicates the state of these two leads. ...

  • Black Box IC107A-R3 - page 18

    NOTES ...

  • Black Box IC107A-R3 - page 19

    NOTES ...

  • Black Box IC107A-R3 - page 20

    1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746 © Copyright 2001. Black Box Corporation. All rights reserved. ...

Produzent Black Box Kategorie Cable Box

Dokumente, die wir vom Produzenten des Geräts Black Box IC107A-R3 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Black Box
- Bedienungsanleitungen IC107A-R3
- Produktkarten Black Box
- Informationsbroschüren
- oder Energieetiketten Black Box IC107A-R3
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Black Box IC107A-R3.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Black Box IC107A-R3, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Black Box IC107A-R3. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Black Box IC107A-R3 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Black Box IC107A-R3, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Black Box IC107A-R3 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Black Box IC107A-R3 verständlich ist.

Eine gänzliche Bedienungsanleitung von Black Box sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Black Box IC107A-R3 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Black Box IC107A-R3 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Black Box IC107A-R3, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Black Box IC107A-R3 - die uns die ersten Schritte während der Nutzung von Black Box IC107A-R3 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Black Box IC107A-R3 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Black Box IC107A-R3 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Black Box IC107A-R3?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Black Box IC107A-R3 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Black Box IC107A-R3 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)