Deutsch dropdown-ico

Bedienungsanleitung Cub Cadet LT1050

36 Seiten 4.64 mb
Download

Zur Seite of 36

Summary
  • Cub Cadet LT1050 - page 1

    FORM NO . 769-01514B.fm (12/13/2004 ) IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y PRINTED IN U .S.A. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-co vered land unless the engine’s exhaust system is equipped with a spark ...

  • Cub Cadet LT1050 - page 2

    2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Ma nual is an important part of your new lawn tractor. It will help you assemble, pr epare and maintain the unit fo r best performance. Plea se read and understand wh at it says. Before you start as sembling your new equipment , plea se locate the model plate on th e equipment and copy the ...

  • Cub Cadet LT1050 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out import ant safety instructions wh ich, if not followed, could endan ger the personal safe ty and/or propert y of yourself and o thers. Read and follo w all instructions in this manua l before attemptin g to operate this machine . Failure to comply with these instruction ...

  • Cub Cadet LT1050 - page 4

    4 23. Muf fler and engine become hot and can cause a burn. Do not touch. 24. Check overhead cle arances carefully before driving under low hang ing tree branches, wire s, door openings etc ., where the oper ator may be struck or pulled from the unit, which could re sult in serious injury. 25. Disenga ge all attachment clutches, depress t he brake p ...

  • Cub Cadet LT1050 - page 5

    5 e. Use extreme car e when approaching blind corners, doorways, sh rubs, trees or other objects that may block your vision of a child who may run into th e machine. f. To avoid back-over ac cidents, always disengage the cutting blad e(s) before shifting i nto reverse. The “Reverse Caution Mode” should not be used when children or others are ar ...

  • Cub Cadet LT1050 - page 6

    6 8. Never tamper with the safety interlock syst em or other safety devices. Check the ir proper operation regu larly. 9. After striking a foreign ob ject, stop the engine, disconnect the spark plug wire(s) and ground against the engine. Thoroug hly inspect the machine for any damage. Repair the damage bef ore starting an d operating. 10. Never att ...

  • Cub Cadet LT1050 - page 7

    7 SECTION 2: SLOPE GAUGE 3IGHTANDHOLDTHISLEVELWITHAVERTICALTREE ORACORNEROFABUILDING ORAFENCEPOST &OLDALONGDOTTEDLINEREPRESENTSASLOPE  ...

  • Cub Cadet LT1050 - page 8

    8 SECTION 3: TRACTOR SET-UP Gas and Oil Fill-up The gasoline tank is located un der the fender and has a capacity of three gallons. Unt hread the fuel cap by turning it counterclockwise . Use only clean, fresh (under 30 days old), unleaded gasoline. Fill tank to no more than four inches below the top of the filler neck to allow space for fuel expan ...

  • Cub Cadet LT1050 - page 9

    9 SECTION 4: KNOW YOUR LAWN TRACTOR Figure 1 NOTE: Any reference in this manual to t he RIGHT or LEFT si de of the tra ctor is observed from operat or’s position. A Systems Indicator M onitor/Hour Meter H PTO (Blade Enga ge) Knob B Throttle Control Lever I Brake Pedal C Choke Contro l J Drive Pedal D Parking Brake Le ver K Cruise Control Lever E ...

  • Cub Cadet LT1050 - page 10

    10 Thro tt l e C on t rol Le ver The throttle co ntrol lever is located on the left side of the tractor’s dash panel. This lever controls the spee d of the engine. When set in a given positio n, the throttle will maintain a uniform engine speed. IMPORT ANT: When operating th e tractor with the cu tting deck engaged, be certain that the throttle l ...

  • Cub Cadet LT1050 - page 11

    11 Hour Meter Located in the ce nter of the tracto r’s console, the ho ur meter operat es whenever the ignition key is rota ted out of the STOP position and recor ds the actual hours of tractor op eration. See Figu re 3. Figure 3 System Indicator Lights Your tractor is equipped with four indicator lights in the center of its dash panel. If the Br ...

  • Cub Cadet LT1050 - page 12

    12 SECTION 5: OPERATING YOUR LAWN TRACTOR Safety Interlock Switches This tractor is equipped with a safet y interlock system for the pr otection of the ope rator. If the interlock system should ever malfunction, do not operate the tractor . Contact you r Cub Cadet dealer. • The safety interlock syste m prevents the engine from cranking or starti ...

  • Cub Cadet LT1050 - page 13

    13 Setting the Gauge Wheels Select the height posit ion of the cutting deck by placing the deck lift lever in any of the six d ifferent cutting height notches on the ri ght fender. Adjust the deck wheels so th at they are between ¼-inch and ½-inch above the gr ound as follows. WARNING: Keep hands and feet away from the dischar ge opening of the c ...

  • Cub Cadet LT1050 - page 14

    14 Engaging the Pa rking Brake To engage the parking brake: • Fully depress the b rake pedal and hold it there while gently p ushing the parking br ake lever downward. • Hold the parking brake lever down while removing your foot from the brake pedal. • Once engaged, t he parking brake lever and the brake pedal will lock in the “down” posi ...

  • Cub Cadet LT1050 - page 15

    15 • Depress the br ake pedal to disengage the cruise control and stop the tractor. • Lightly depress th e drive pedal. To change the directi on of travel to reverse when operating with cruise control, depress the brake pedal to disengag e the cruise control an d bring the tractor to a complete stop. Then slo wly depress the rear portion of the ...

  • Cub Cadet LT1050 - page 16

    16 • For best result s it is recommended that the first two laps be cut with the discharge thrown towar ds the center. A fter the firs t two laps, reverse the directio n to throw th e discharge to the ou tside for the balance of cuttin g. This will give a bett er appearance to the lawn. • Do not cut the grass t oo short. Short grass invites wee ...

  • Cub Cadet LT1050 - page 17

    17 SECTION 6: MAKING ADJUSTMENTS WARNING: Ne v er attempt to make an y adjustments while the engine is running, e xcept where specified in th e operator’ s manual . Leveling the Deck NOTE: Check the tractor’ s tire pressure before performing any de ck leveling adjustments. Refer to Tires on page 25 for informati on regarding tire pressure. Fron ...

  • Cub Cadet LT1050 - page 18

    18 P arking Brake Adjustment WARNING: Never attempt to a djust the brakes while the engin e is running. Always disengage PTO, stop eng ine and remove ke y to prevent uninten ded starting. If the tractor does not co me to a complete stop when the brake peda l is completely depres sed, or if the tractor’s rear wheels can roll with the pa rking brak ...

  • Cub Cadet LT1050 - page 19

    19 SECTION 7: MAINTAINING YOUR LAWN TRACTOR NOTE: Re fer to Maintenance Chart on page 30 for a reference of recommend ed maintenance intervals. WARNING: Before performing any maintenance or rep airs, disengage PTO, set parking brake, st op engine and remove key to prevent unint ended starti ng. Engine Maintenance, repa ir, or replacement of the emi ...

  • Cub Cadet LT1050 - page 20

    20 • Remove the oil fill cap/dipsti ck from the oil fill tube and SLOWLY pour oil into the oil fill tube. Do NOT pour more t han 6 oz. o f oil at a tim e without fir st stopping and re-checkin g the oil level. • Fill the crankcase until the oil level reaches the full ( F ) mark on the dipstick. Refer to Figure 14. Refer to the viscosity oil cha ...

  • Cub Cadet LT1050 - page 21

    21 Re-filling the Crankcase with Oil IMPORT ANT: On models LT10 42 & LT 1045, the en gine (with oil filter) ha s a capacity of 1.5 liters (50. 75 oz.). On models LT1046 & LT 1050, the engine (with oil filter) has a capacity of 2.0 liters (67.60 oz.) Do NOT over fill. Always check the level on the dipstick as instructed on page 19 before add ...

  • Cub Cadet LT1050 - page 22

    22 Spark Plug(s) Every 200 hours of operation, remo ve the spark plug(s), check condit ion, and reset the gap or replace with a new plug(s) as necessary. • Lift the tr actor’s hood an d locate the spar k plug wire on the fro nt, right area of the engine . • Carefully pull the spark plug wire boot o ff of the spark plug. • Before rem oving t ...

  • Cub Cadet LT1050 - page 23

    23 7. Move the tractor’s PTO (Blade Engage) into the ON position. 8. Remain in the operator’s position with the cutting deck engaged for a minimum o f two minutes, allowing the underside of the cutting deck to thoroughly rinse. 9. Move the tractor’s PTO (Blade Enga ge) into the OFF position. 10. Turn the ignition key to the STOP position to t ...

  • Cub Cadet LT1050 - page 24

    24 • Make sure the fuel tank is filled with clean, fresh gasoline. • Make sure the fuel tank cap vent is not blocked and that it is operating prop erly. • If the fuel tank is equippe d with a shut-off valv e, make sure it is open. • Make sure that the in-lin e fuel filter is clean and unobstructed. Replace the filter if necessary. • Make ...

  • Cub Cadet LT1050 - page 25

    25 SECTION 8: SERVICE Tire s WARNING: Never exceed the maxim um inflation pressure sh own on the sidewall of the tire. The recommende d operating tire pressur e is approximately 1 0 psi for the rear tires a nd 14 psi for the front tires. Refer to th e tire sidewa ll for exact t ire manufa cturer’s recommended or maximum psi. Do no t overinflate. ...

  • Cub Cadet LT1050 - page 26

    26 Battery The battery is sealed and is maintenance-free. Acid levels cannot be checked and f luid can not be added. • Always keep the battery ca bles and terminals clean and free o f corrosive build-up. • After cleaning the bat tery and terminals, apply a light coat of petroleum jelly or grease to both terminals • Always keep the rubber boot ...

  • Cub Cadet LT1050 - page 27

    27 Hydrostatic T ransmission Keep the area around the transmission cooling fan free of grass and debris at all ti mes. The hydrostatic transmission is sealed at the factory and is maintenance fr ee. The fluid level ca nnot be checked and on most models , cannot be changed. If your tr actor is equipped wi t h a transmission drain plug (see Figure 23 ...

  • Cub Cadet LT1050 - page 28

    28 46-inch Decks • Insert a 3/8”-drive r atchet wren ch (set to loosen ) into the squa re hole found in the idler bracke t on the left side of the deck’s sur face. See Figure 25. Figure 2 5 • Grasp the ratche t’s handle and pivot it toward the tractor’s right side to relieve tension on the belt. • With belt tension relieved, car efull ...

  • Cub Cadet LT1050 - page 29

    29 L T1042 L T1050 L T1045 & L T1046 ...

  • Cub Cadet LT1050 - page 30

    30 SECTION 9: OFF-SEASON STORAGE Clean and lubricate the tr actor as instructed in Section 7: MAINTAINING YOUR LAWN TRACTOR on page 19 of this manual before sto ring for an extended period . Engine If the engine will be out of service for tw o months or more, use the followin g storage procedure: • Clean the exterior surfac es of the engine. • ...

  • Cub Cadet LT1050 - page 31

    31 SECTION 11: TROUBLESHOOTING T r ouble Poss ible Cause(s) Corrective Actio n Engine fails to start PT O/Blade Engage knob engaged . P arking brake not engaged. Spark pl ug wire(s) disconnected. Throttle control le v er not in correct star ting position. Chok e not activ ated Fuel tank empty , or stale fuel. Bloc ked fuel line. F aulty spark pl ug ...

  • Cub Cadet LT1050 - page 32

    32 SECTION 12: ATTACHMENTS & ACCESSORIES The following attach ments and accessories are compatib le for Series 1000 Lawn Tractors . See your Cub Cadet dealer or the retailer from which yo u purchased your trac tor for informat ion regarding price and availability. NOTE: Cub Cadet Series 1000 lawn tractors are NOT designed f or use with any type ...

  • Cub Cadet LT1050 - page 33

    33 SECTION 13: SPECIFICATIONS L T1042 L T1045 L T1046 L T1050 Capaciti es Fuel Tank 13.2 liters (3.5 gallons) 13.2 liters (3.5 gallons) 13.2 liters (3.5 gallons) 13.2 liters (3.5 gallons) Engine Crankcase (w/ filter) 1.5 liters (50.75 oz.) 1.5 liters (50.75 oz.) 2.0 liters (67.6 oz.) 2.0 liters (67.6 oz.) Transmission 2.25 liters (76 oz.) 2. 25 lit ...

  • Cub Cadet LT1050 - page 34

    K OHLER CO . FEDERAL AND CALI FORNIA EMISSION CONTROL SYSTEMS LIMITED W ARRANTY UTILITY AND LA WN AND GARDEN ENGINES The U.S. Environmental Protection Agency (EP A) , the California Air Resources Board (CARB), and K ohler Co. are pleased to explain the Federal and California Emission Control Systems Warr anty on your small off-road equipment engine ...

  • Cub Cadet LT1050 - page 35

    CUB CADET LLC MANUFACTURER’S ONE YE AR LIMITED WARRANTY (COMMERCIAL USE) The limited warranty set f or th below is given b y CUB CADET LLC (“CUB CADET”) with respect to new merchandise pur- chased and used in the United Sta tes, its possessions and territor ies. CUB CADET warrants this product against def ects in mate- rial an d workmanship f ...

  • Cub Cadet LT1050 - page 36

    36 CUB CADET LLC MANUFACTURER’S LIMITED WARRANTY (RESIDENTIAL USE) The limited warranty set f or th below is given b y CUB CADET LLC (“CUB CADET”) with respect to new merchandise pur- chased and used in the United States, its possessions an d territor ies. CUB CADET warrants this product against def ects in material and workmanship f or a per ...

Produzent Cub Cadet Kategorie Lawn Mower

Dokumente, die wir vom Produzenten des Geräts Cub Cadet LT1050 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cub Cadet
- Bedienungsanleitungen LT1050
- Produktkarten Cub Cadet
- Informationsbroschüren
- oder Energieetiketten Cub Cadet LT1050
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cub Cadet LT1050.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cub Cadet LT1050, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cub Cadet LT1050. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cub Cadet LT1050 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cub Cadet LT1050, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cub Cadet LT1050 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cub Cadet LT1050 verständlich ist.

Eine gänzliche Bedienungsanleitung von Cub Cadet sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cub Cadet LT1050 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cub Cadet LT1050 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cub Cadet LT1050, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cub Cadet LT1050 - die uns die ersten Schritte während der Nutzung von Cub Cadet LT1050 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cub Cadet LT1050 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cub Cadet LT1050 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cub Cadet LT1050?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cub Cadet LT1050 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cub Cadet LT1050 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)