Bedienungsanleitung Heatcraft Refrigeration Products none

20 Seiten 0.66 mb
Download

Zur Seite of 20

Summary
  • Heatcraft Refrigeration Products none - page 1

    T able of C onten ts Air-C ooled C ondensers Installation and Opera tion Guide I n s p e c t i o n .............................................. 2 System W arranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 I n s t a l l a t i o n ............................................. 2 U n i t L o c a t i o n ....... ...

  • Heatcraft Refrigeration Products none - page 2

    2 © 2008, Heatcraft Refrigeration Products LL C Inspection Responsibility should be assigned to a dependable individual at the job site to rec eive material. Each shipment should be car efully checked against the bill of lading. The shipping receipt should not be signed until all items listed on the bill of lading ha ve been accounted f or . Check ...

  • Heatcraft Refrigeration Products none - page 3

    3 Drawing 1. Rigging Instructions ...

  • Heatcraft Refrigeration Products none - page 4

    4 Space and Location Requir ements The most important consideration which must be taken into account when deciding upon the loca tion of air-cooled equipment is the provision f or a supply of ambient air to the condenser , and removal of heated air fr om the condenser area. Where this essential r equirement is not adhered to , it will result in hig ...

  • Heatcraft Refrigeration Products none - page 5

    5 T ypical Arrangements Figur e 1 illustrates a typical piping arrangement inv olving a remote condenser locat ed at a higher elevation, as commonly encountered when the condenser is on a r oof and the compressor and receiver ar e on grade level or in a basement equipment room. In this case, the design of the discharge line is very critical. If pro ...

  • Heatcraft Refrigeration Products none - page 6

    6 Electric al Wiring The electrical installation should be in accordance with National Electrical Code, local codes and regulations . Proper o vercurrent protection should be provided f or the fan motors. All standard motors hav e internal inherent ov erload protectors. Theref ore, contactors can be used instead of starters requiring thermal protec ...

  • Heatcraft Refrigeration Products none - page 7

    7 Diagram 1. T ypical Condenser Wiring Diagram with F an C ycle Contr ols ...

  • Heatcraft Refrigeration Products none - page 8

    8 Start-Up Check for proper fan r otation. Air is drawn through the c oil on all units. Be sure the fans turn freely . Rotation of the motors and blades should be in a “CW ” direction looking at the unit from the blade side. On three phase units , it may be necessary to reverse two of the three po wer leads to the unit. NO TE: The manifold asse ...

  • Heatcraft Refrigeration Products none - page 9

    9 F an C ycling Head Pr essure C ontrols Condenser fans are cycled to maintain adequat e head pressure. Ambient and pressure fan cycling ar e available as optional equipment. Ambient fan cycling cycles fans in response to the ambient air temperature . This control is ideal for multi-circuited condensers or for systems oper ating in mild ambient con ...

  • Heatcraft Refrigeration Products none - page 10

    10 T able 3. Minimum Ambient for F an Cy cling Number of F ans Single Double Design T .D.* Row Row 30 25 20 15 10 2 4 35 45 55 60 70 3 6 15 30 40 55 65 4 8 0 15 30 45 60 5 10 0 10 20 35 55 6 / 7 12 / 14 0 0 10 30 50 * Based on maintaining 90°F minimum condensing tempera ture. T able 4. Mechanical F an C ycling Thermostat Settings Number of Fans Si ...

  • Heatcraft Refrigeration Products none - page 11

    11 T able 5. Elec tronic F an C ycling Thermostat Settings * Number of F ans A350 S350 T emperature Stage Modules Single Double Design Set Oset Settings Row Rows T .D . Point 2 3 4 5 30 60 25 65 2 4 20 70 15 75 10 80 30 60 20 25 65 10 3 6 20 70 10 15 75 10 10 80 15 30 60 10 30 25 65 10 25 4 8 20 70 5 20 15 75 5 15 10 80 5 10 30 60 5 15 30 25 65 ...

  • Heatcraft Refrigeration Products none - page 12

    12 T able 7. Refrigerant Char ge for F an Cy cling plus Flooded Condenser (lbs. R-22) Model* Summer Charge 25° TD 20° TD 15° TD 10° TD 40°F 20°F 0°F -20°F 40°F 20°F 0°F -20°F 40°F 20°F 0°F -20°F 40°F 20°F 0°F -20°F 1 8 7 8 9 9 8 9 10 10 9 10 11 11 13 12 12 12 2 10 9 12 13 14 11 13 14 15 13 14 15 16 17 18 17 18 3 10 1 6 8 10 4 8 ...

  • Heatcraft Refrigeration Products none - page 13

    13 T able 9. Flooded Charge T emperature Dier ence F ac tor Ambient, °F Design T .D. 30 25 20 15 10 +60 – 0.38 1.0 1.74 2.46 +40 0.59 0.80 1.0 1.19 1.40 +20 0.76 0.88 1.0 1.13 1.25 0 0.84 0.91 1.0 1.07 1.16 -20 0.88 0.93 1.0 1.05 1.13 T able 10. Model Cross Reference Model Reference *NH *NL *NX *NQ *NE 1 *NH-S01-A007 *NL -S01-A007 *NX-S01-A00 ...

  • Heatcraft Refrigeration Products none - page 14

    14 F an RPM Motor HP F an Motor Part No . F an Blade Part No . F an Guard Part No . 1140 (H Models) 1.5 25316401 22900401 23105701 1140 ( Var . Speed) 0.75 25317101 2292625 23105701 830 (L Models) 1.5 25316601 22929501 23105701 830 (X Models) 1 25316301 22929501 23105701 540 (Q Models) 0.5 25316201 22929301 23105701 1030 (E Models, 230V ) 2.2 kW 25 ...

  • Heatcraft Refrigeration Products none - page 15

    15 E Series Motors with Integra ted V ariable Speed E Series units use an EC motor/fan blade combination to pro vide variable speed condenser control . All components requir ed to run the motor at variable speeds ar e built into the motor . Speed Adjustment Char acteristics The EC motor varies it’ s speed linearly based on a 0-10V input signal. A ...

  • Heatcraft Refrigeration Products none - page 16

    16 Head Pressur e Setpoint The head pressur e setpoint potentiometer is adjustable from 90-250 psig . A typical setpoints are from 170-200 psig. Note: Very low setpoints may cause the fan motors t o run full speed continually if the condenser is not pr operly sized. The fans will turn o if the system pr essure falls below the desired setpoint. M ...

  • Heatcraft Refrigeration Products none - page 17

    17 Master/Slav e Conguration The EC motor contr ol signals are wir ed in a Master/ Slave c onguration. This conguration allows f or the maximum sound and energy reduction as well as the most stable head pressure c ontrol. The contr ol signal is delivered t o the master motor (located at the header end of the unit). The master motor relay s ...

  • Heatcraft Refrigeration Products none - page 18

    18 TYPICAL 1X4 EC MOT OR WIRING WITH 0-10V DC CONTROL SIGNAL RS B RS A 12 11 4-20mA 0-10V GND RS A RS B PWM 0-10V PWM +20V +10V OUT GND NC COM NO L2 L3 L1 PE KL3 10 9 7 8 6 5 3 4 2 1 1 3 2 KL2 2 3 1 KL1 PE BLK RED RS B RS A 12 11 4-20mA 0-10V GND RS A RS B PWM 0-10V PWM +20V +10V OUT GND NC COM NO L2 L3 L1 PE KL3 10 9 7 8 6 5 3 4 2 1 1 3 2 KL2 2 3 ...

  • Heatcraft Refrigeration Products none - page 19

    19 NOTE: 1. UNIT MUST BE GROUNDED. 2. TO BE FIELD FUSED, REFER TO UNIT DA T APLATE FOR VOL TA GE. 3. ALL MOTORS ARE INHERENTL Y PROTECTED. 4. USE 60°C WIRE. 5. REFER TO LABEL ADJACENT FUSE HOLDER FOR REPLACEMENT . USE COPPER CONDUCT ORS ONL Y FIELD WIRING F ACTORY WIRING C F AN CONT ACTOR M F AN MOTOR F FUSES R RELA Y FCC F AN CYCLE CONTROL (MA Y ...

  • Heatcraft Refrigeration Products none - page 20

    20 Installation Check List Since product improv ement is a continuing eort, we reserve the right to make changes in specications without notice. C L I M A T E C O N T R O L Commercial Refrigeration Parts The name behind the brands you trust. ™ H-IM-90-0808 C ondenser Start Up Date Model # Serial # Electric al V oltage Amperage Installer: Na ...

Produzent Heatcraft Refrigeration Products Kategorie Humidifier

Dokumente, die wir vom Produzenten des Geräts Heatcraft Refrigeration Products none erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Heatcraft Refrigeration Products
- Bedienungsanleitungen none
- Produktkarten Heatcraft Refrigeration Products
- Informationsbroschüren
- oder Energieetiketten Heatcraft Refrigeration Products none
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Heatcraft Refrigeration Products none.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Heatcraft Refrigeration Products none, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Heatcraft Refrigeration Products none. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Heatcraft Refrigeration Products none ansehen.

Die komplette Bedienungsanleitung des Geräts Heatcraft Refrigeration Products none, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Heatcraft Refrigeration Products none hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Heatcraft Refrigeration Products none verständlich ist.

Eine gänzliche Bedienungsanleitung von Heatcraft Refrigeration Products sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Heatcraft Refrigeration Products none bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Heatcraft Refrigeration Products none befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Heatcraft Refrigeration Products none, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Heatcraft Refrigeration Products none - die uns die ersten Schritte während der Nutzung von Heatcraft Refrigeration Products none erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Heatcraft Refrigeration Products none hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Heatcraft Refrigeration Products none im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Heatcraft Refrigeration Products none?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Heatcraft Refrigeration Products none nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Heatcraft Refrigeration Products none hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)