Bedienungsanleitung Pelco CCC5100H

16 Seiten 0.94 mb
Download

Zur Seite of 16

Summary
  • Pelco CCC5100H - page 1

    QUICK START GUIDE C2910M-B- Q S (2/06) CCC5100H Series Camera ...

  • Pelco CCC5100H - page 2

    2 C2910M-B-QS (2/06) This quick start guide describes how to install and confi gure the CCC5100H Series camera in most applications. It contains a representation of the setup menus to help you locate and change specific settings. BEFO R E Y OU BEGIN DOCUMENT A TION Refer to the enclosed CD for the following documentation: • Installation/Operati ...

  • Pelco CCC5100H - page 3

    C2910M-B-QS (2/06) 3 H AR DW AR E Refer to Figure 1 as you install the CCC5100H Series camera. Figure 1. CCC5100H Connectors VIDEO CONNECTOR SERVICE CONNECTOR SETUP BUTTONS MULTIFUNCTION (RJ45-10) CONNECTOR POWER CONNECTOR BACK FOCUS ADJUSTMENT C/CS LENS AUTO IRIS LENS CABLE AND CONNECTOR (OPTIONAL) ...

  • Pelco CCC5100H - page 4

    4 C2910M-B-QS (2/06) LENS The CCC5100H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. The camera accepts both CS- and C-mount lenses without an adapter . T o mount the lens onto the camera: 1. Use clean, compressed air to remove any dust or other foreign matter between the lens and the cam ...

  • Pelco CCC5100H - page 5

    C2910M-B-QS (2/06) 5 CONNECTIONS The CCC5100H Series camera offers standard power and coax video connectors. T o use the RJ45-10 multifunction connector that combines power, video, and control leads, refer to Multifunction Connector in the Installation/Operation manual. LOW V OLT A GE POWE R Connect 12 VDC or 24 VAC power to the two-pin power conne ...

  • Pelco CCC5100H - page 6

    6 C2910M-B-QS (2/06) SETUP MENUS Use the setup menus to customize the camera settings. Refer to the setup menus as shown on this and the opposite page: CAMERA DISPLAY CAMERA NAME CCC5100H RX ADDRESS 1 SAVE RX ADDRESS <DISPLAY PROPERTIES> <GAMMA/SATURATION> <GAIN CONTROL> <SHARPNESS> BACK EXIT LANGUAGE ENGLISH ESPA Ñ OL P OR ...

  • Pelco CCC5100H - page 7

    C2910M-B-QS (2/06) 7 WHITE BALANCE MODE ATW NORMAL <ATW NORMAL /DESAT> <MANUAL RED/BLUE> <MANUAL COLOR TEMP> BACK EXIT ATW NORMAL /DESAT LOW LIMIT HIGH LIMIT BACK EXIT |------+------| |------+------| 2k 5.5k 5.5k 11k PROFILES ACTIVE WDR SAVE AS CUSTOM1 DEFAULT WDR BACK EXIT SYSTEM INFORMATION FIRMWARE VER. 1.1.1 OSD VER. 1.12.0 RE ...

  • Pelco CCC5100H - page 8

    8 C2910M-B-QS (2/06) A CCESSING THE SETUP MENUS Use the top, center , and bottom buttons on the rear panel to access and navigate the setup menus. T able A lists the button presses for each menu action. A short press is less than one second; a long press is more than one second. Throughout the rest of this guide, “press” means a short press; ? ...

  • Pelco CCC5100H - page 9

    C2910M-B-QS (2/06) 9 C A ME RA P R OFILE Select a basic camera profile and then customize it. After you save your custom camera settings into a user-definable profile, change the default to CUSTOM1 or CUSTOM2. C A UTION: Be sure to save all camera settings into a user-definable profile so they will not be lost in case the camera loses power . ...

  • Pelco CCC5100H - page 10

    10 C2910M-B-QS (2/06) 4. Select the user-definable profile to use during power -up: a. Select DEFAUL T and press the center button. b. Press the top or bottom button to select your profi le: CUSTOM1 or CUSTOM2. c. Press the center button to set the new default profi le. The display blinks and the cursor exits to the menu. The camera sets the DE ...

  • Pelco CCC5100H - page 11

    C2910M-B-QS (2/06) 11 DC-D R IVE A UTO I R IS LENS SETUP Before using a DC-drive auto iris lens, you must adjust the DC offset setting. Use the following steps to match the camera’ s DC voltage setting to the drive circuit on the auto iris lens: 1. Remove the lens from the camera. 2. Place the front end of the camera face down on a fl at surface ...

  • Pelco CCC5100H - page 12

    12 C2910M-B-QS (2/06) 9. Hold the auto iris lens so you can watch the iris (refer to Figure 3). Then increase the DC OFFSET setting slowly until the iris closes. Figure 3. Open Iris and Closed Iris 10. As soon as the iris closes, slowly decrease the DC OFFSET value by 14, or until the iris opens again. 11. Select SA VE DC OFFSET to save the DC OFFS ...

  • Pelco CCC5100H - page 13

    C2910M-B-QS (2/06) 13 LENS FOCUS Focus the camera lens. 1. A uto iris only: Cover the auto iris lens with a suitable neutral density (ND) filter to open the iris fully . For best results, use an ND3 filter . 2. Manual iris only: Open the iris completely . 3. If necessary , enable automatic gain control (AGC) on the LENS/VIDEO SIGNAL menu. Figure ...

  • Pelco CCC5100H - page 14

    14 C2910M-B-QS (2/06) 6. Fixed focal length lens only: a. Set the lens focal length to far ( ∞ ). b. Adjust the back focus. Move the back focus locking screw on the camera up or down until the image is focused. As the focus improves, the value on the FINE FOCUS menu increases: the higher the number, the better the focus. c. Adjust the lens focus ...

  • Pelco CCC5100H - page 15

    C2910M-B-QS (2/06) 15 R evision History Manual No. Date Comments C2910M-QS 9/04 Original version. C2910M-A-QS 4/05 Updated for RGB filters, new firmware. C2910M-B-QS 2/06 Removed the high voltage and RGB models. Updated the OSD version. Changed the active profile default. Added DC-drive auto iris setup procedure. Updated model numbers. Pelco and ...

  • Pelco CCC5100H - page 16

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Produzent Pelco Kategorie Home Security System

Dokumente, die wir vom Produzenten des Geräts Pelco CCC5100H erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pelco
- Bedienungsanleitungen CCC5100H
- Produktkarten Pelco
- Informationsbroschüren
- oder Energieetiketten Pelco CCC5100H
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pelco CCC5100H.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pelco CCC5100H, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pelco CCC5100H. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pelco CCC5100H ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pelco CCC5100H, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pelco CCC5100H hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pelco CCC5100H verständlich ist.

Eine gänzliche Bedienungsanleitung von Pelco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pelco CCC5100H bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pelco CCC5100H befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pelco CCC5100H, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pelco CCC5100H - die uns die ersten Schritte während der Nutzung von Pelco CCC5100H erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pelco CCC5100H hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pelco CCC5100H im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pelco CCC5100H?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco CCC5100H nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco CCC5100H hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)